linux/drivers/parport/parport_pc.c
<<
>>
Prefs
   1/* Low-level parallel-port routines for 8255-based PC-style hardware.
   2 *
   3 * Authors: Phil Blundell <philb@gnu.org>
   4 *          Tim Waugh <tim@cyberelk.demon.co.uk>
   5 *          Jose Renau <renau@acm.org>
   6 *          David Campbell
   7 *          Andrea Arcangeli
   8 *
   9 * based on work by Grant Guenther <grant@torque.net> and Phil Blundell.
  10 *
  11 * Cleaned up include files - Russell King <linux@arm.uk.linux.org>
  12 * DMA support - Bert De Jonghe <bert@sophis.be>
  13 * Many ECP bugs fixed.  Fred Barnes & Jamie Lokier, 1999
  14 * More PCI support now conditional on CONFIG_PCI, 03/2001, Paul G.
  15 * Various hacks, Fred Barnes, 04/2001
  16 * Updated probing logic - Adam Belay <ambx1@neo.rr.com>
  17 */
  18
  19/* This driver should work with any hardware that is broadly compatible
  20 * with that in the IBM PC.  This applies to the majority of integrated
  21 * I/O chipsets that are commonly available.  The expected register
  22 * layout is:
  23 *
  24 *      base+0          data
  25 *      base+1          status
  26 *      base+2          control
  27 *
  28 * In addition, there are some optional registers:
  29 *
  30 *      base+3          EPP address
  31 *      base+4          EPP data
  32 *      base+0x400      ECP config A
  33 *      base+0x401      ECP config B
  34 *      base+0x402      ECP control
  35 *
  36 * All registers are 8 bits wide and read/write.  If your hardware differs
  37 * only in register addresses (eg because your registers are on 32-bit
  38 * word boundaries) then you can alter the constants in parport_pc.h to
  39 * accommodate this.
  40 *
  41 * Note that the ECP registers may not start at offset 0x400 for PCI cards,
  42 * but rather will start at port->base_hi.
  43 */
  44
  45#include <linux/module.h>
  46#include <linux/init.h>
  47#include <linux/sched.h>
  48#include <linux/delay.h>
  49#include <linux/errno.h>
  50#include <linux/interrupt.h>
  51#include <linux/ioport.h>
  52#include <linux/kernel.h>
  53#include <linux/slab.h>
  54#include <linux/dma-mapping.h>
  55#include <linux/pci.h>
  56#include <linux/pnp.h>
  57#include <linux/platform_device.h>
  58#include <linux/sysctl.h>
  59#include <linux/io.h>
  60#include <linux/uaccess.h>
  61
  62#include <asm/dma.h>
  63
  64#include <linux/parport.h>
  65#include <linux/parport_pc.h>
  66#include <linux/via.h>
  67#include <asm/parport.h>
  68
  69#define PARPORT_PC_MAX_PORTS PARPORT_MAX
  70
  71#ifdef CONFIG_ISA_DMA_API
  72#define HAS_DMA
  73#endif
  74
  75/* ECR modes */
  76#define ECR_SPP 00
  77#define ECR_PS2 01
  78#define ECR_PPF 02
  79#define ECR_ECP 03
  80#define ECR_EPP 04
  81#define ECR_VND 05
  82#define ECR_TST 06
  83#define ECR_CNF 07
  84#define ECR_MODE_MASK 0xe0
  85#define ECR_WRITE(p, v) frob_econtrol((p), 0xff, (v))
  86
  87#undef DEBUG
  88
  89#ifdef DEBUG
  90#define DPRINTK  printk
  91#else
  92#define DPRINTK(stuff...)
  93#endif
  94
  95
  96#define NR_SUPERIOS 3
  97static struct superio_struct {  /* For Super-IO chips autodetection */
  98        int io;
  99        int irq;
 100        int dma;
 101} superios[NR_SUPERIOS] = { {0,},};
 102
 103static int user_specified;
 104#if defined(CONFIG_PARPORT_PC_SUPERIO) || \
 105       (defined(CONFIG_PARPORT_1284) && defined(CONFIG_PARPORT_PC_FIFO))
 106static int verbose_probing;
 107#endif
 108static int pci_registered_parport;
 109static int pnp_registered_parport;
 110
 111/* frob_control, but for ECR */
 112static void frob_econtrol(struct parport *pb, unsigned char m,
 113                           unsigned char v)
 114{
 115        unsigned char ectr = 0;
 116
 117        if (m != 0xff)
 118                ectr = inb(ECONTROL(pb));
 119
 120        DPRINTK(KERN_DEBUG "frob_econtrol(%02x,%02x): %02x -> %02x\n",
 121                m, v, ectr, (ectr & ~m) ^ v);
 122
 123        outb((ectr & ~m) ^ v, ECONTROL(pb));
 124}
 125
 126static inline void frob_set_mode(struct parport *p, int mode)
 127{
 128        frob_econtrol(p, ECR_MODE_MASK, mode << 5);
 129}
 130
 131#ifdef CONFIG_PARPORT_PC_FIFO
 132/* Safely change the mode bits in the ECR
 133   Returns:
 134            0    : Success
 135           -EBUSY: Could not drain FIFO in some finite amount of time,
 136                   mode not changed!
 137 */
 138static int change_mode(struct parport *p, int m)
 139{
 140        const struct parport_pc_private *priv = p->physport->private_data;
 141        unsigned char oecr;
 142        int mode;
 143
 144        DPRINTK(KERN_INFO "parport change_mode ECP-ISA to mode 0x%02x\n", m);
 145
 146        if (!priv->ecr) {
 147                printk(KERN_DEBUG "change_mode: but there's no ECR!\n");
 148                return 0;
 149        }
 150
 151        /* Bits <7:5> contain the mode. */
 152        oecr = inb(ECONTROL(p));
 153        mode = (oecr >> 5) & 0x7;
 154        if (mode == m)
 155                return 0;
 156
 157        if (mode >= 2 && !(priv->ctr & 0x20)) {
 158                /* This mode resets the FIFO, so we may
 159                 * have to wait for it to drain first. */
 160                unsigned long expire = jiffies + p->physport->cad->timeout;
 161                int counter;
 162                switch (mode) {
 163                case ECR_PPF: /* Parallel Port FIFO mode */
 164                case ECR_ECP: /* ECP Parallel Port mode */
 165                        /* Busy wait for 200us */
 166                        for (counter = 0; counter < 40; counter++) {
 167                                if (inb(ECONTROL(p)) & 0x01)
 168                                        break;
 169                                if (signal_pending(current))
 170                                        break;
 171                                udelay(5);
 172                        }
 173
 174                        /* Poll slowly. */
 175                        while (!(inb(ECONTROL(p)) & 0x01)) {
 176                                if (time_after_eq(jiffies, expire))
 177                                        /* The FIFO is stuck. */
 178                                        return -EBUSY;
 179                                schedule_timeout_interruptible(
 180                                                        msecs_to_jiffies(10));
 181                                if (signal_pending(current))
 182                                        break;
 183                        }
 184                }
 185        }
 186
 187        if (mode >= 2 && m >= 2) {
 188                /* We have to go through mode 001 */
 189                oecr &= ~(7 << 5);
 190                oecr |= ECR_PS2 << 5;
 191                ECR_WRITE(p, oecr);
 192        }
 193
 194        /* Set the mode. */
 195        oecr &= ~(7 << 5);
 196        oecr |= m << 5;
 197        ECR_WRITE(p, oecr);
 198        return 0;
 199}
 200
 201#ifdef CONFIG_PARPORT_1284
 202/* Find FIFO lossage; FIFO is reset */
 203#if 0
 204static int get_fifo_residue(struct parport *p)
 205{
 206        int residue;
 207        int cnfga;
 208        const struct parport_pc_private *priv = p->physport->private_data;
 209
 210        /* Adjust for the contents of the FIFO. */
 211        for (residue = priv->fifo_depth; ; residue--) {
 212                if (inb(ECONTROL(p)) & 0x2)
 213                                /* Full up. */
 214                        break;
 215
 216                outb(0, FIFO(p));
 217        }
 218
 219        printk(KERN_DEBUG "%s: %d PWords were left in FIFO\n", p->name,
 220                residue);
 221
 222        /* Reset the FIFO. */
 223        frob_set_mode(p, ECR_PS2);
 224
 225        /* Now change to config mode and clean up. FIXME */
 226        frob_set_mode(p, ECR_CNF);
 227        cnfga = inb(CONFIGA(p));
 228        printk(KERN_DEBUG "%s: cnfgA contains 0x%02x\n", p->name, cnfga);
 229
 230        if (!(cnfga & (1<<2))) {
 231                printk(KERN_DEBUG "%s: Accounting for extra byte\n", p->name);
 232                residue++;
 233        }
 234
 235        /* Don't care about partial PWords until support is added for
 236         * PWord != 1 byte. */
 237
 238        /* Back to PS2 mode. */
 239        frob_set_mode(p, ECR_PS2);
 240
 241        DPRINTK(KERN_DEBUG
 242             "*** get_fifo_residue: done residue collecting (ecr = 0x%2.2x)\n",
 243                                                        inb(ECONTROL(p)));
 244        return residue;
 245}
 246#endif  /*  0 */
 247#endif /* IEEE 1284 support */
 248#endif /* FIFO support */
 249
 250/*
 251 * Clear TIMEOUT BIT in EPP MODE
 252 *
 253 * This is also used in SPP detection.
 254 */
 255static int clear_epp_timeout(struct parport *pb)
 256{
 257        unsigned char r;
 258
 259        if (!(parport_pc_read_status(pb) & 0x01))
 260                return 1;
 261
 262        /* To clear timeout some chips require double read */
 263        parport_pc_read_status(pb);
 264        r = parport_pc_read_status(pb);
 265        outb(r | 0x01, STATUS(pb)); /* Some reset by writing 1 */
 266        outb(r & 0xfe, STATUS(pb)); /* Others by writing 0 */
 267        r = parport_pc_read_status(pb);
 268
 269        return !(r & 0x01);
 270}
 271
 272/*
 273 * Access functions.
 274 *
 275 * Most of these aren't static because they may be used by the
 276 * parport_xxx_yyy macros.  extern __inline__ versions of several
 277 * of these are in parport_pc.h.
 278 */
 279
 280static void parport_pc_init_state(struct pardevice *dev,
 281                                                struct parport_state *s)
 282{
 283        s->u.pc.ctr = 0xc;
 284        if (dev->irq_func &&
 285            dev->port->irq != PARPORT_IRQ_NONE)
 286                /* Set ackIntEn */
 287                s->u.pc.ctr |= 0x10;
 288
 289        s->u.pc.ecr = 0x34; /* NetMos chip can cause problems 0x24;
 290                             * D.Gruszka VScom */
 291}
 292
 293static void parport_pc_save_state(struct parport *p, struct parport_state *s)
 294{
 295        const struct parport_pc_private *priv = p->physport->private_data;
 296        s->u.pc.ctr = priv->ctr;
 297        if (priv->ecr)
 298                s->u.pc.ecr = inb(ECONTROL(p));
 299}
 300
 301static void parport_pc_restore_state(struct parport *p,
 302                                                struct parport_state *s)
 303{
 304        struct parport_pc_private *priv = p->physport->private_data;
 305        register unsigned char c = s->u.pc.ctr & priv->ctr_writable;
 306        outb(c, CONTROL(p));
 307        priv->ctr = c;
 308        if (priv->ecr)
 309                ECR_WRITE(p, s->u.pc.ecr);
 310}
 311
 312#ifdef CONFIG_PARPORT_1284
 313static size_t parport_pc_epp_read_data(struct parport *port, void *buf,
 314                                       size_t length, int flags)
 315{
 316        size_t got = 0;
 317
 318        if (flags & PARPORT_W91284PIC) {
 319                unsigned char status;
 320                size_t left = length;
 321
 322                /* use knowledge about data lines..:
 323                 *  nFault is 0 if there is at least 1 byte in the Warp's FIFO
 324                 *  pError is 1 if there are 16 bytes in the Warp's FIFO
 325                 */
 326                status = inb(STATUS(port));
 327
 328                while (!(status & 0x08) && got < length) {
 329                        if (left >= 16 && (status & 0x20) && !(status & 0x08)) {
 330                                /* can grab 16 bytes from warp fifo */
 331                                if (!((long)buf & 0x03))
 332                                        insl(EPPDATA(port), buf, 4);
 333                                else
 334                                        insb(EPPDATA(port), buf, 16);
 335                                buf += 16;
 336                                got += 16;
 337                                left -= 16;
 338                        } else {
 339                                /* grab single byte from the warp fifo */
 340                                *((char *)buf) = inb(EPPDATA(port));
 341                                buf++;
 342                                got++;
 343                                left--;
 344                        }
 345                        status = inb(STATUS(port));
 346                        if (status & 0x01) {
 347                                /* EPP timeout should never occur... */
 348                                printk(KERN_DEBUG
 349"%s: EPP timeout occurred while talking to w91284pic (should not have done)\n", port->name);
 350                                clear_epp_timeout(port);
 351                        }
 352                }
 353                return got;
 354        }
 355        if ((flags & PARPORT_EPP_FAST) && (length > 1)) {
 356                if (!(((long)buf | length) & 0x03))
 357                        insl(EPPDATA(port), buf, (length >> 2));
 358                else
 359                        insb(EPPDATA(port), buf, length);
 360                if (inb(STATUS(port)) & 0x01) {
 361                        clear_epp_timeout(port);
 362                        return -EIO;
 363                }
 364                return length;
 365        }
 366        for (; got < length; got++) {
 367                *((char *)buf) = inb(EPPDATA(port));
 368                buf++;
 369                if (inb(STATUS(port)) & 0x01) {
 370                        /* EPP timeout */
 371                        clear_epp_timeout(port);
 372                        break;
 373                }
 374        }
 375
 376        return got;
 377}
 378
 379static size_t parport_pc_epp_write_data(struct parport *port, const void *buf,
 380                                        size_t length, int flags)
 381{
 382        size_t written = 0;
 383
 384        if ((flags & PARPORT_EPP_FAST) && (length > 1)) {
 385                if (!(((long)buf | length) & 0x03))
 386                        outsl(EPPDATA(port), buf, (length >> 2));
 387                else
 388                        outsb(EPPDATA(port), buf, length);
 389                if (inb(STATUS(port)) & 0x01) {
 390                        clear_epp_timeout(port);
 391                        return -EIO;
 392                }
 393                return length;
 394        }
 395        for (; written < length; written++) {
 396                outb(*((char *)buf), EPPDATA(port));
 397                buf++;
 398                if (inb(STATUS(port)) & 0x01) {
 399                        clear_epp_timeout(port);
 400                        break;
 401                }
 402        }
 403
 404        return written;
 405}
 406
 407static size_t parport_pc_epp_read_addr(struct parport *port, void *buf,
 408                                        size_t length, int flags)
 409{
 410        size_t got = 0;
 411
 412        if ((flags & PARPORT_EPP_FAST) && (length > 1)) {
 413                insb(EPPADDR(port), buf, length);
 414                if (inb(STATUS(port)) & 0x01) {
 415                        clear_epp_timeout(port);
 416                        return -EIO;
 417                }
 418                return length;
 419        }
 420        for (; got < length; got++) {
 421                *((char *)buf) = inb(EPPADDR(port));
 422                buf++;
 423                if (inb(STATUS(port)) & 0x01) {
 424                        clear_epp_timeout(port);
 425                        break;
 426                }
 427        }
 428
 429        return got;
 430}
 431
 432static size_t parport_pc_epp_write_addr(struct parport *port,
 433                                         const void *buf, size_t length,
 434                                         int flags)
 435{
 436        size_t written = 0;
 437
 438        if ((flags & PARPORT_EPP_FAST) && (length > 1)) {
 439                outsb(EPPADDR(port), buf, length);
 440                if (inb(STATUS(port)) & 0x01) {
 441                        clear_epp_timeout(port);
 442                        return -EIO;
 443                }
 444                return length;
 445        }
 446        for (; written < length; written++) {
 447                outb(*((char *)buf), EPPADDR(port));
 448                buf++;
 449                if (inb(STATUS(port)) & 0x01) {
 450                        clear_epp_timeout(port);
 451                        break;
 452                }
 453        }
 454
 455        return written;
 456}
 457
 458static size_t parport_pc_ecpepp_read_data(struct parport *port, void *buf,
 459                                          size_t length, int flags)
 460{
 461        size_t got;
 462
 463        frob_set_mode(port, ECR_EPP);
 464        parport_pc_data_reverse(port);
 465        parport_pc_write_control(port, 0x4);
 466        got = parport_pc_epp_read_data(port, buf, length, flags);
 467        frob_set_mode(port, ECR_PS2);
 468
 469        return got;
 470}
 471
 472static size_t parport_pc_ecpepp_write_data(struct parport *port,
 473                                           const void *buf, size_t length,
 474                                           int flags)
 475{
 476        size_t written;
 477
 478        frob_set_mode(port, ECR_EPP);
 479        parport_pc_write_control(port, 0x4);
 480        parport_pc_data_forward(port);
 481        written = parport_pc_epp_write_data(port, buf, length, flags);
 482        frob_set_mode(port, ECR_PS2);
 483
 484        return written;
 485}
 486
 487static size_t parport_pc_ecpepp_read_addr(struct parport *port, void *buf,
 488                                          size_t length, int flags)
 489{
 490        size_t got;
 491
 492        frob_set_mode(port, ECR_EPP);
 493        parport_pc_data_reverse(port);
 494        parport_pc_write_control(port, 0x4);
 495        got = parport_pc_epp_read_addr(port, buf, length, flags);
 496        frob_set_mode(port, ECR_PS2);
 497
 498        return got;
 499}
 500
 501static size_t parport_pc_ecpepp_write_addr(struct parport *port,
 502                                            const void *buf, size_t length,
 503                                            int flags)
 504{
 505        size_t written;
 506
 507        frob_set_mode(port, ECR_EPP);
 508        parport_pc_write_control(port, 0x4);
 509        parport_pc_data_forward(port);
 510        written = parport_pc_epp_write_addr(port, buf, length, flags);
 511        frob_set_mode(port, ECR_PS2);
 512
 513        return written;
 514}
 515#endif /* IEEE 1284 support */
 516
 517#ifdef CONFIG_PARPORT_PC_FIFO
 518static size_t parport_pc_fifo_write_block_pio(struct parport *port,
 519                                               const void *buf, size_t length)
 520{
 521        int ret = 0;
 522        const unsigned char *bufp = buf;
 523        size_t left = length;
 524        unsigned long expire = jiffies + port->physport->cad->timeout;
 525        const int fifo = FIFO(port);
 526        int poll_for = 8; /* 80 usecs */
 527        const struct parport_pc_private *priv = port->physport->private_data;
 528        const int fifo_depth = priv->fifo_depth;
 529
 530        port = port->physport;
 531
 532        /* We don't want to be interrupted every character. */
 533        parport_pc_disable_irq(port);
 534        /* set nErrIntrEn and serviceIntr */
 535        frob_econtrol(port, (1<<4) | (1<<2), (1<<4) | (1<<2));
 536
 537        /* Forward mode. */
 538        parport_pc_data_forward(port); /* Must be in PS2 mode */
 539
 540        while (left) {
 541                unsigned char byte;
 542                unsigned char ecrval = inb(ECONTROL(port));
 543                int i = 0;
 544
 545                if (need_resched() && time_before(jiffies, expire))
 546                        /* Can't yield the port. */
 547                        schedule();
 548
 549                /* Anyone else waiting for the port? */
 550                if (port->waithead) {
 551                        printk(KERN_DEBUG "Somebody wants the port\n");
 552                        break;
 553                }
 554
 555                if (ecrval & 0x02) {
 556                        /* FIFO is full. Wait for interrupt. */
 557
 558                        /* Clear serviceIntr */
 559                        ECR_WRITE(port, ecrval & ~(1<<2));
 560false_alarm:
 561                        ret = parport_wait_event(port, HZ);
 562                        if (ret < 0)
 563                                break;
 564                        ret = 0;
 565                        if (!time_before(jiffies, expire)) {
 566                                /* Timed out. */
 567                                printk(KERN_DEBUG "FIFO write timed out\n");
 568                                break;
 569                        }
 570                        ecrval = inb(ECONTROL(port));
 571                        if (!(ecrval & (1<<2))) {
 572                                if (need_resched() &&
 573                                    time_before(jiffies, expire))
 574                                        schedule();
 575
 576                                goto false_alarm;
 577                        }
 578
 579                        continue;
 580                }
 581
 582                /* Can't fail now. */
 583                expire = jiffies + port->cad->timeout;
 584
 585poll:
 586                if (signal_pending(current))
 587                        break;
 588
 589                if (ecrval & 0x01) {
 590                        /* FIFO is empty. Blast it full. */
 591                        const int n = left < fifo_depth ? left : fifo_depth;
 592                        outsb(fifo, bufp, n);
 593                        bufp += n;
 594                        left -= n;
 595
 596                        /* Adjust the poll time. */
 597                        if (i < (poll_for - 2))
 598                                poll_for--;
 599                        continue;
 600                } else if (i++ < poll_for) {
 601                        udelay(10);
 602                        ecrval = inb(ECONTROL(port));
 603                        goto poll;
 604                }
 605
 606                /* Half-full(call me an optimist) */
 607                byte = *bufp++;
 608                outb(byte, fifo);
 609                left--;
 610        }
 611        dump_parport_state("leave fifo_write_block_pio", port);
 612        return length - left;
 613}
 614
 615#ifdef HAS_DMA
 616static size_t parport_pc_fifo_write_block_dma(struct parport *port,
 617                                               const void *buf, size_t length)
 618{
 619        int ret = 0;
 620        unsigned long dmaflag;
 621        size_t left = length;
 622        const struct parport_pc_private *priv = port->physport->private_data;
 623        struct device *dev = port->physport->dev;
 624        dma_addr_t dma_addr, dma_handle;
 625        size_t maxlen = 0x10000; /* max 64k per DMA transfer */
 626        unsigned long start = (unsigned long) buf;
 627        unsigned long end = (unsigned long) buf + length - 1;
 628
 629        dump_parport_state("enter fifo_write_block_dma", port);
 630        if (end < MAX_DMA_ADDRESS) {
 631                /* If it would cross a 64k boundary, cap it at the end. */
 632                if ((start ^ end) & ~0xffffUL)
 633                        maxlen = 0x10000 - (start & 0xffff);
 634
 635                dma_addr = dma_handle = dma_map_single(dev, (void *)buf, length,
 636                                                       DMA_TO_DEVICE);
 637        } else {
 638                /* above 16 MB we use a bounce buffer as ISA-DMA
 639                   is not possible */
 640                maxlen   = PAGE_SIZE;          /* sizeof(priv->dma_buf) */
 641                dma_addr = priv->dma_handle;
 642                dma_handle = 0;
 643        }
 644
 645        port = port->physport;
 646
 647        /* We don't want to be interrupted every character. */
 648        parport_pc_disable_irq(port);
 649        /* set nErrIntrEn and serviceIntr */
 650        frob_econtrol(port, (1<<4) | (1<<2), (1<<4) | (1<<2));
 651
 652        /* Forward mode. */
 653        parport_pc_data_forward(port); /* Must be in PS2 mode */
 654
 655        while (left) {
 656                unsigned long expire = jiffies + port->physport->cad->timeout;
 657
 658                size_t count = left;
 659
 660                if (count > maxlen)
 661                        count = maxlen;
 662
 663                if (!dma_handle)   /* bounce buffer ! */
 664                        memcpy(priv->dma_buf, buf, count);
 665
 666                dmaflag = claim_dma_lock();
 667                disable_dma(port->dma);
 668                clear_dma_ff(port->dma);
 669                set_dma_mode(port->dma, DMA_MODE_WRITE);
 670                set_dma_addr(port->dma, dma_addr);
 671                set_dma_count(port->dma, count);
 672
 673                /* Set DMA mode */
 674                frob_econtrol(port, 1<<3, 1<<3);
 675
 676                /* Clear serviceIntr */
 677                frob_econtrol(port, 1<<2, 0);
 678
 679                enable_dma(port->dma);
 680                release_dma_lock(dmaflag);
 681
 682                /* assume DMA will be successful */
 683                left -= count;
 684                buf  += count;
 685                if (dma_handle)
 686                        dma_addr += count;
 687
 688                /* Wait for interrupt. */
 689false_alarm:
 690                ret = parport_wait_event(port, HZ);
 691                if (ret < 0)
 692                        break;
 693                ret = 0;
 694                if (!time_before(jiffies, expire)) {
 695                        /* Timed out. */
 696                        printk(KERN_DEBUG "DMA write timed out\n");
 697                        break;
 698                }
 699                /* Is serviceIntr set? */
 700                if (!(inb(ECONTROL(port)) & (1<<2))) {
 701                        cond_resched();
 702
 703                        goto false_alarm;
 704                }
 705
 706                dmaflag = claim_dma_lock();
 707                disable_dma(port->dma);
 708                clear_dma_ff(port->dma);
 709                count = get_dma_residue(port->dma);
 710                release_dma_lock(dmaflag);
 711
 712                cond_resched(); /* Can't yield the port. */
 713
 714                /* Anyone else waiting for the port? */
 715                if (port->waithead) {
 716                        printk(KERN_DEBUG "Somebody wants the port\n");
 717                        break;
 718                }
 719
 720                /* update for possible DMA residue ! */
 721                buf  -= count;
 722                left += count;
 723                if (dma_handle)
 724                        dma_addr -= count;
 725        }
 726
 727        /* Maybe got here through break, so adjust for DMA residue! */
 728        dmaflag = claim_dma_lock();
 729        disable_dma(port->dma);
 730        clear_dma_ff(port->dma);
 731        left += get_dma_residue(port->dma);
 732        release_dma_lock(dmaflag);
 733
 734        /* Turn off DMA mode */
 735        frob_econtrol(port, 1<<3, 0);
 736
 737        if (dma_handle)
 738                dma_unmap_single(dev, dma_handle, length, DMA_TO_DEVICE);
 739
 740        dump_parport_state("leave fifo_write_block_dma", port);
 741        return length - left;
 742}
 743#endif
 744
 745static inline size_t parport_pc_fifo_write_block(struct parport *port,
 746                                               const void *buf, size_t length)
 747{
 748#ifdef HAS_DMA
 749        if (port->dma != PARPORT_DMA_NONE)
 750                return parport_pc_fifo_write_block_dma(port, buf, length);
 751#endif
 752        return parport_pc_fifo_write_block_pio(port, buf, length);
 753}
 754
 755/* Parallel Port FIFO mode (ECP chipsets) */
 756static size_t parport_pc_compat_write_block_pio(struct parport *port,
 757                                                 const void *buf, size_t length,
 758                                                 int flags)
 759{
 760        size_t written;
 761        int r;
 762        unsigned long expire;
 763        const struct parport_pc_private *priv = port->physport->private_data;
 764
 765        /* Special case: a timeout of zero means we cannot call schedule().
 766         * Also if O_NONBLOCK is set then use the default implementation. */
 767        if (port->physport->cad->timeout <= PARPORT_INACTIVITY_O_NONBLOCK)
 768                return parport_ieee1284_write_compat(port, buf,
 769                                                      length, flags);
 770
 771        /* Set up parallel port FIFO mode.*/
 772        parport_pc_data_forward(port); /* Must be in PS2 mode */
 773        parport_pc_frob_control(port, PARPORT_CONTROL_STROBE, 0);
 774        r = change_mode(port, ECR_PPF); /* Parallel port FIFO */
 775        if (r)
 776                printk(KERN_DEBUG "%s: Warning change_mode ECR_PPF failed\n",
 777                                                                port->name);
 778
 779        port->physport->ieee1284.phase = IEEE1284_PH_FWD_DATA;
 780
 781        /* Write the data to the FIFO. */
 782        written = parport_pc_fifo_write_block(port, buf, length);
 783
 784        /* Finish up. */
 785        /* For some hardware we don't want to touch the mode until
 786         * the FIFO is empty, so allow 4 seconds for each position
 787         * in the fifo.
 788         */
 789        expire = jiffies + (priv->fifo_depth * HZ * 4);
 790        do {
 791                /* Wait for the FIFO to empty */
 792                r = change_mode(port, ECR_PS2);
 793                if (r != -EBUSY)
 794                        break;
 795        } while (time_before(jiffies, expire));
 796        if (r == -EBUSY) {
 797
 798                printk(KERN_DEBUG "%s: FIFO is stuck\n", port->name);
 799
 800                /* Prevent further data transfer. */
 801                frob_set_mode(port, ECR_TST);
 802
 803                /* Adjust for the contents of the FIFO. */
 804                for (written -= priv->fifo_depth; ; written++) {
 805                        if (inb(ECONTROL(port)) & 0x2) {
 806                                /* Full up. */
 807                                break;
 808                        }
 809                        outb(0, FIFO(port));
 810                }
 811
 812                /* Reset the FIFO and return to PS2 mode. */
 813                frob_set_mode(port, ECR_PS2);
 814        }
 815
 816        r = parport_wait_peripheral(port,
 817                                     PARPORT_STATUS_BUSY,
 818                                     PARPORT_STATUS_BUSY);
 819        if (r)
 820                printk(KERN_DEBUG
 821                        "%s: BUSY timeout (%d) in compat_write_block_pio\n",
 822                        port->name, r);
 823
 824        port->physport->ieee1284.phase = IEEE1284_PH_FWD_IDLE;
 825
 826        return written;
 827}
 828
 829/* ECP */
 830#ifdef CONFIG_PARPORT_1284
 831static size_t parport_pc_ecp_write_block_pio(struct parport *port,
 832                                              const void *buf, size_t length,
 833                                              int flags)
 834{
 835        size_t written;
 836        int r;
 837        unsigned long expire;
 838        const struct parport_pc_private *priv = port->physport->private_data;
 839
 840        /* Special case: a timeout of zero means we cannot call schedule().
 841         * Also if O_NONBLOCK is set then use the default implementation. */
 842        if (port->physport->cad->timeout <= PARPORT_INACTIVITY_O_NONBLOCK)
 843                return parport_ieee1284_ecp_write_data(port, buf,
 844                                                        length, flags);
 845
 846        /* Switch to forward mode if necessary. */
 847        if (port->physport->ieee1284.phase != IEEE1284_PH_FWD_IDLE) {
 848                /* Event 47: Set nInit high. */
 849                parport_frob_control(port,
 850                                      PARPORT_CONTROL_INIT
 851                                      | PARPORT_CONTROL_AUTOFD,
 852                                      PARPORT_CONTROL_INIT
 853                                      | PARPORT_CONTROL_AUTOFD);
 854
 855                /* Event 49: PError goes high. */
 856                r = parport_wait_peripheral(port,
 857                                             PARPORT_STATUS_PAPEROUT,
 858                                             PARPORT_STATUS_PAPEROUT);
 859                if (r) {
 860                        printk(KERN_DEBUG "%s: PError timeout (%d) "
 861                                "in ecp_write_block_pio\n", port->name, r);
 862                }
 863        }
 864
 865        /* Set up ECP parallel port mode.*/
 866        parport_pc_data_forward(port); /* Must be in PS2 mode */
 867        parport_pc_frob_control(port,
 868                                 PARPORT_CONTROL_STROBE |
 869                                 PARPORT_CONTROL_AUTOFD,
 870                                 0);
 871        r = change_mode(port, ECR_ECP); /* ECP FIFO */
 872        if (r)
 873                printk(KERN_DEBUG "%s: Warning change_mode ECR_ECP failed\n",
 874                                                                port->name);
 875        port->physport->ieee1284.phase = IEEE1284_PH_FWD_DATA;
 876
 877        /* Write the data to the FIFO. */
 878        written = parport_pc_fifo_write_block(port, buf, length);
 879
 880        /* Finish up. */
 881        /* For some hardware we don't want to touch the mode until
 882         * the FIFO is empty, so allow 4 seconds for each position
 883         * in the fifo.
 884         */
 885        expire = jiffies + (priv->fifo_depth * (HZ * 4));
 886        do {
 887                /* Wait for the FIFO to empty */
 888                r = change_mode(port, ECR_PS2);
 889                if (r != -EBUSY)
 890                        break;
 891        } while (time_before(jiffies, expire));
 892        if (r == -EBUSY) {
 893
 894                printk(KERN_DEBUG "%s: FIFO is stuck\n", port->name);
 895
 896                /* Prevent further data transfer. */
 897                frob_set_mode(port, ECR_TST);
 898
 899                /* Adjust for the contents of the FIFO. */
 900                for (written -= priv->fifo_depth; ; written++) {
 901                        if (inb(ECONTROL(port)) & 0x2) {
 902                                /* Full up. */
 903                                break;
 904                        }
 905                        outb(0, FIFO(port));
 906                }
 907
 908                /* Reset the FIFO and return to PS2 mode. */
 909                frob_set_mode(port, ECR_PS2);
 910
 911                /* Host transfer recovery. */
 912                parport_pc_data_reverse(port); /* Must be in PS2 mode */
 913                udelay(5);
 914                parport_frob_control(port, PARPORT_CONTROL_INIT, 0);
 915                r = parport_wait_peripheral(port, PARPORT_STATUS_PAPEROUT, 0);
 916                if (r)
 917                        printk(KERN_DEBUG "%s: PE,1 timeout (%d) "
 918                                "in ecp_write_block_pio\n", port->name, r);
 919
 920                parport_frob_control(port,
 921                                      PARPORT_CONTROL_INIT,
 922                                      PARPORT_CONTROL_INIT);
 923                r = parport_wait_peripheral(port,
 924                                             PARPORT_STATUS_PAPEROUT,
 925                                             PARPORT_STATUS_PAPEROUT);
 926                if (r)
 927                        printk(KERN_DEBUG "%s: PE,2 timeout (%d) "
 928                                "in ecp_write_block_pio\n", port->name, r);
 929        }
 930
 931        r = parport_wait_peripheral(port,
 932                                     PARPORT_STATUS_BUSY,
 933                                     PARPORT_STATUS_BUSY);
 934        if (r)
 935                printk(KERN_DEBUG
 936                        "%s: BUSY timeout (%d) in ecp_write_block_pio\n",
 937                        port->name, r);
 938
 939        port->physport->ieee1284.phase = IEEE1284_PH_FWD_IDLE;
 940
 941        return written;
 942}
 943
 944#if 0
 945static size_t parport_pc_ecp_read_block_pio(struct parport *port,
 946                                             void *buf, size_t length,
 947                                             int flags)
 948{
 949        size_t left = length;
 950        size_t fifofull;
 951        int r;
 952        const int fifo = FIFO(port);
 953        const struct parport_pc_private *priv = port->physport->private_data;
 954        const int fifo_depth = priv->fifo_depth;
 955        char *bufp = buf;
 956
 957        port = port->physport;
 958        DPRINTK(KERN_DEBUG "parport_pc: parport_pc_ecp_read_block_pio\n");
 959        dump_parport_state("enter fcn", port);
 960
 961        /* Special case: a timeout of zero means we cannot call schedule().
 962         * Also if O_NONBLOCK is set then use the default implementation. */
 963        if (port->cad->timeout <= PARPORT_INACTIVITY_O_NONBLOCK)
 964                return parport_ieee1284_ecp_read_data(port, buf,
 965                                                       length, flags);
 966
 967        if (port->ieee1284.mode == IEEE1284_MODE_ECPRLE) {
 968                /* If the peripheral is allowed to send RLE compressed
 969                 * data, it is possible for a byte to expand to 128
 970                 * bytes in the FIFO. */
 971                fifofull = 128;
 972        } else {
 973                fifofull = fifo_depth;
 974        }
 975
 976        /* If the caller wants less than a full FIFO's worth of data,
 977         * go through software emulation.  Otherwise we may have to throw
 978         * away data. */
 979        if (length < fifofull)
 980                return parport_ieee1284_ecp_read_data(port, buf,
 981                                                       length, flags);
 982
 983        if (port->ieee1284.phase != IEEE1284_PH_REV_IDLE) {
 984                /* change to reverse-idle phase (must be in forward-idle) */
 985
 986                /* Event 38: Set nAutoFd low (also make sure nStrobe is high) */
 987                parport_frob_control(port,
 988                                      PARPORT_CONTROL_AUTOFD
 989                                      | PARPORT_CONTROL_STROBE,
 990                                      PARPORT_CONTROL_AUTOFD);
 991                parport_pc_data_reverse(port); /* Must be in PS2 mode */
 992                udelay(5);
 993                /* Event 39: Set nInit low to initiate bus reversal */
 994                parport_frob_control(port,
 995                                      PARPORT_CONTROL_INIT,
 996                                      0);
 997                /* Event 40: Wait for  nAckReverse (PError) to go low */
 998                r = parport_wait_peripheral(port, PARPORT_STATUS_PAPEROUT, 0);
 999                if (r) {
1000                        printk(KERN_DEBUG "%s: PE timeout Event 40 (%d) "
1001                                "in ecp_read_block_pio\n", port->name, r);
1002                        return 0;
1003                }
1004        }
1005
1006        /* Set up ECP FIFO mode.*/
1007/*      parport_pc_frob_control(port,
1008                                 PARPORT_CONTROL_STROBE |
1009                                 PARPORT_CONTROL_AUTOFD,
1010                                 PARPORT_CONTROL_AUTOFD); */
1011        r = change_mode(port, ECR_ECP); /* ECP FIFO */
1012        if (r)
1013                printk(KERN_DEBUG "%s: Warning change_mode ECR_ECP failed\n",
1014                                                                port->name);
1015
1016        port->ieee1284.phase = IEEE1284_PH_REV_DATA;
1017
1018        /* the first byte must be collected manually */
1019        dump_parport_state("pre 43", port);
1020        /* Event 43: Wait for nAck to go low */
1021        r = parport_wait_peripheral(port, PARPORT_STATUS_ACK, 0);
1022        if (r) {
1023                /* timed out while reading -- no data */
1024                printk(KERN_DEBUG "PIO read timed out (initial byte)\n");
1025                goto out_no_data;
1026        }
1027        /* read byte */
1028        *bufp++ = inb(DATA(port));
1029        left--;
1030        dump_parport_state("43-44", port);
1031        /* Event 44: nAutoFd (HostAck) goes high to acknowledge */
1032        parport_pc_frob_control(port,
1033                                 PARPORT_CONTROL_AUTOFD,
1034                                 0);
1035        dump_parport_state("pre 45", port);
1036        /* Event 45: Wait for nAck to go high */
1037        /* r = parport_wait_peripheral(port, PARPORT_STATUS_ACK,
1038                                                PARPORT_STATUS_ACK); */
1039        dump_parport_state("post 45", port);
1040        r = 0;
1041        if (r) {
1042                /* timed out while waiting for peripheral to respond to ack */
1043                printk(KERN_DEBUG "ECP PIO read timed out (waiting for nAck)\n");
1044
1045                /* keep hold of the byte we've got already */
1046                goto out_no_data;
1047        }
1048        /* Event 46: nAutoFd (HostAck) goes low to accept more data */
1049        parport_pc_frob_control(port,
1050                                 PARPORT_CONTROL_AUTOFD,
1051                                 PARPORT_CONTROL_AUTOFD);
1052
1053
1054        dump_parport_state("rev idle", port);
1055        /* Do the transfer. */
1056        while (left > fifofull) {
1057                int ret;
1058                unsigned long expire = jiffies + port->cad->timeout;
1059                unsigned char ecrval = inb(ECONTROL(port));
1060
1061                if (need_resched() && time_before(jiffies, expire))
1062                        /* Can't yield the port. */
1063                        schedule();
1064
1065                /* At this point, the FIFO may already be full. In
1066                 * that case ECP is already holding back the
1067                 * peripheral (assuming proper design) with a delayed
1068                 * handshake.  Work fast to avoid a peripheral
1069                 * timeout.  */
1070
1071                if (ecrval & 0x01) {
1072                        /* FIFO is empty. Wait for interrupt. */
1073                        dump_parport_state("FIFO empty", port);
1074
1075                        /* Anyone else waiting for the port? */
1076                        if (port->waithead) {
1077                                printk(KERN_DEBUG "Somebody wants the port\n");
1078                                break;
1079                        }
1080
1081                        /* Clear serviceIntr */
1082                        ECR_WRITE(port, ecrval & ~(1<<2));
1083false_alarm:
1084                        dump_parport_state("waiting", port);
1085                        ret = parport_wait_event(port, HZ);
1086                        DPRINTK(KERN_DEBUG "parport_wait_event returned %d\n",
1087                                                                        ret);
1088                        if (ret < 0)
1089                                break;
1090                        ret = 0;
1091                        if (!time_before(jiffies, expire)) {
1092                                /* Timed out. */
1093                                dump_parport_state("timeout", port);
1094                                printk(KERN_DEBUG "PIO read timed out\n");
1095                                break;
1096                        }
1097                        ecrval = inb(ECONTROL(port));
1098                        if (!(ecrval & (1<<2))) {
1099                                if (need_resched() &&
1100                                    time_before(jiffies, expire)) {
1101                                        schedule();
1102                                }
1103                                goto false_alarm;
1104                        }
1105
1106                        /* Depending on how the FIFO threshold was
1107                         * set, how long interrupt service took, and
1108                         * how fast the peripheral is, we might be
1109                         * lucky and have a just filled FIFO. */
1110                        continue;
1111                }
1112
1113                if (ecrval & 0x02) {
1114                        /* FIFO is full. */
1115                        dump_parport_state("FIFO full", port);
1116                        insb(fifo, bufp, fifo_depth);
1117                        bufp += fifo_depth;
1118                        left -= fifo_depth;
1119                        continue;
1120                }
1121
1122                DPRINTK(KERN_DEBUG
1123                  "*** ecp_read_block_pio: reading one byte from the FIFO\n");
1124
1125                /* FIFO not filled.  We will cycle this loop for a while
1126                 * and either the peripheral will fill it faster,
1127                 * tripping a fast empty with insb, or we empty it. */
1128                *bufp++ = inb(fifo);
1129                left--;
1130        }
1131
1132        /* scoop up anything left in the FIFO */
1133        while (left && !(inb(ECONTROL(port) & 0x01))) {
1134                *bufp++ = inb(fifo);
1135                left--;
1136        }
1137
1138        port->ieee1284.phase = IEEE1284_PH_REV_IDLE;
1139        dump_parport_state("rev idle2", port);
1140
1141out_no_data:
1142
1143        /* Go to forward idle mode to shut the peripheral up (event 47). */
1144        parport_frob_control(port, PARPORT_CONTROL_INIT, PARPORT_CONTROL_INIT);
1145
1146        /* event 49: PError goes high */
1147        r = parport_wait_peripheral(port,
1148                                     PARPORT_STATUS_PAPEROUT,
1149                                     PARPORT_STATUS_PAPEROUT);
1150        if (r) {
1151                printk(KERN_DEBUG
1152                        "%s: PE timeout FWDIDLE (%d) in ecp_read_block_pio\n",
1153                        port->name, r);
1154        }
1155
1156        port->ieee1284.phase = IEEE1284_PH_FWD_IDLE;
1157
1158        /* Finish up. */
1159        {
1160                int lost = get_fifo_residue(port);
1161                if (lost)
1162                        /* Shouldn't happen with compliant peripherals. */
1163                        printk(KERN_DEBUG "%s: DATA LOSS (%d bytes)!\n",
1164                                port->name, lost);
1165        }
1166
1167        dump_parport_state("fwd idle", port);
1168        return length - left;
1169}
1170#endif  /*  0  */
1171#endif /* IEEE 1284 support */
1172#endif /* Allowed to use FIFO/DMA */
1173
1174
1175/*
1176 *      ******************************************
1177 *      INITIALISATION AND MODULE STUFF BELOW HERE
1178 *      ******************************************
1179 */
1180
1181/* GCC is not inlining extern inline function later overwriten to non-inline,
1182   so we use outlined_ variants here.  */
1183static const struct parport_operations parport_pc_ops = {
1184        .write_data     = parport_pc_write_data,
1185        .read_data      = parport_pc_read_data,
1186
1187        .write_control  = parport_pc_write_control,
1188        .read_control   = parport_pc_read_control,
1189        .frob_control   = parport_pc_frob_control,
1190
1191        .read_status    = parport_pc_read_status,
1192
1193        .enable_irq     = parport_pc_enable_irq,
1194        .disable_irq    = parport_pc_disable_irq,
1195
1196        .data_forward   = parport_pc_data_forward,
1197        .data_reverse   = parport_pc_data_reverse,
1198
1199        .init_state     = parport_pc_init_state,
1200        .save_state     = parport_pc_save_state,
1201        .restore_state  = parport_pc_restore_state,
1202
1203        .epp_write_data = parport_ieee1284_epp_write_data,
1204        .epp_read_data  = parport_ieee1284_epp_read_data,
1205        .epp_write_addr = parport_ieee1284_epp_write_addr,
1206        .epp_read_addr  = parport_ieee1284_epp_read_addr,
1207
1208        .ecp_write_data = parport_ieee1284_ecp_write_data,
1209        .ecp_read_data  = parport_ieee1284_ecp_read_data,
1210        .ecp_write_addr = parport_ieee1284_ecp_write_addr,
1211
1212        .compat_write_data      = parport_ieee1284_write_compat,
1213        .nibble_read_data       = parport_ieee1284_read_nibble,
1214        .byte_read_data         = parport_ieee1284_read_byte,
1215
1216        .owner          = THIS_MODULE,
1217};
1218
1219#ifdef CONFIG_PARPORT_PC_SUPERIO
1220
1221static struct superio_struct *find_free_superio(void)
1222{
1223        int i;
1224        for (i = 0; i < NR_SUPERIOS; i++)
1225                if (superios[i].io == 0)
1226                        return &superios[i];
1227        return NULL;
1228}
1229
1230
1231/* Super-IO chipset detection, Winbond, SMSC */
1232static void __devinit show_parconfig_smsc37c669(int io, int key)
1233{
1234        int cr1, cr4, cra, cr23, cr26, cr27;
1235        struct superio_struct *s;
1236
1237        static const char *const modes[] = {
1238                "SPP and Bidirectional (PS/2)",
1239                "EPP and SPP",
1240                "ECP",
1241                "ECP and EPP" };
1242
1243        outb(key, io);
1244        outb(key, io);
1245        outb(1, io);
1246        cr1 = inb(io + 1);
1247        outb(4, io);
1248        cr4 = inb(io + 1);
1249        outb(0x0a, io);
1250        cra = inb(io + 1);
1251        outb(0x23, io);
1252        cr23 = inb(io + 1);
1253        outb(0x26, io);
1254        cr26 = inb(io + 1);
1255        outb(0x27, io);
1256        cr27 = inb(io + 1);
1257        outb(0xaa, io);
1258
1259        if (verbose_probing) {
1260                printk(KERN_INFO
1261                        "SMSC 37c669 LPT Config: cr_1=0x%02x, 4=0x%02x, "
1262                        "A=0x%2x, 23=0x%02x, 26=0x%02x, 27=0x%02x\n",
1263                        cr1, cr4, cra, cr23, cr26, cr27);
1264
1265                /* The documentation calls DMA and IRQ-Lines by letters, so
1266                   the board maker can/will wire them
1267                   appropriately/randomly...  G=reserved H=IDE-irq, */
1268                printk(KERN_INFO
1269        "SMSC LPT Config: io=0x%04x, irq=%c, dma=%c, fifo threshold=%d\n",
1270                                cr23 * 4,
1271                                (cr27 & 0x0f) ? 'A' - 1 + (cr27 & 0x0f) : '-',
1272                                (cr26 & 0x0f) ? 'A' - 1 + (cr26 & 0x0f) : '-',
1273                                cra & 0x0f);
1274                printk(KERN_INFO "SMSC LPT Config: enabled=%s power=%s\n",
1275                       (cr23 * 4 >= 0x100) ? "yes" : "no",
1276                       (cr1 & 4) ? "yes" : "no");
1277                printk(KERN_INFO
1278                        "SMSC LPT Config: Port mode=%s, EPP version =%s\n",
1279                                (cr1 & 0x08) ? "Standard mode only (SPP)"
1280                                              : modes[cr4 & 0x03],
1281                                (cr4 & 0x40) ? "1.7" : "1.9");
1282        }
1283
1284        /* Heuristics !  BIOS setup for this mainboard device limits
1285           the choices to standard settings, i.e. io-address and IRQ
1286           are related, however DMA can be 1 or 3, assume DMA_A=DMA1,
1287           DMA_C=DMA3 (this is true e.g. for TYAN 1564D Tomcat IV) */
1288        if (cr23 * 4 >= 0x100) { /* if active */
1289                s = find_free_superio();
1290                if (s == NULL)
1291                        printk(KERN_INFO "Super-IO: too many chips!\n");
1292                else {
1293                        int d;
1294                        switch (cr23 * 4) {
1295                        case 0x3bc:
1296                                s->io = 0x3bc;
1297                                s->irq = 7;
1298                                break;
1299                        case 0x378:
1300                                s->io = 0x378;
1301                                s->irq = 7;
1302                                break;
1303                        case 0x278:
1304                                s->io = 0x278;
1305                                s->irq = 5;
1306                        }
1307                        d = (cr26 & 0x0f);
1308                        if (d == 1 || d == 3)
1309                                s->dma = d;
1310                        else
1311                                s->dma = PARPORT_DMA_NONE;
1312                }
1313        }
1314}
1315
1316
1317static void __devinit show_parconfig_winbond(int io, int key)
1318{
1319        int cr30, cr60, cr61, cr70, cr74, crf0;
1320        struct superio_struct *s;
1321        static const char *const modes[] = {
1322                "Standard (SPP) and Bidirectional(PS/2)", /* 0 */
1323                "EPP-1.9 and SPP",
1324                "ECP",
1325                "ECP and EPP-1.9",
1326                "Standard (SPP)",
1327                "EPP-1.7 and SPP",              /* 5 */
1328                "undefined!",
1329                "ECP and EPP-1.7" };
1330        static char *const irqtypes[] = {
1331                "pulsed low, high-Z",
1332                "follows nACK" };
1333
1334        /* The registers are called compatible-PnP because the
1335           register layout is modelled after ISA-PnP, the access
1336           method is just another ... */
1337        outb(key, io);
1338        outb(key, io);
1339        outb(0x07, io);   /* Register 7: Select Logical Device */
1340        outb(0x01, io + 1); /* LD1 is Parallel Port */
1341        outb(0x30, io);
1342        cr30 = inb(io + 1);
1343        outb(0x60, io);
1344        cr60 = inb(io + 1);
1345        outb(0x61, io);
1346        cr61 = inb(io + 1);
1347        outb(0x70, io);
1348        cr70 = inb(io + 1);
1349        outb(0x74, io);
1350        cr74 = inb(io + 1);
1351        outb(0xf0, io);
1352        crf0 = inb(io + 1);
1353        outb(0xaa, io);
1354
1355        if (verbose_probing) {
1356                printk(KERN_INFO
1357    "Winbond LPT Config: cr_30=%02x 60,61=%02x%02x 70=%02x 74=%02x, f0=%02x\n",
1358                                        cr30, cr60, cr61, cr70, cr74, crf0);
1359                printk(KERN_INFO "Winbond LPT Config: active=%s, io=0x%02x%02x irq=%d, ",
1360                       (cr30 & 0x01) ? "yes" : "no", cr60, cr61, cr70 & 0x0f);
1361                if ((cr74 & 0x07) > 3)
1362                        printk("dma=none\n");
1363                else
1364                        printk("dma=%d\n", cr74 & 0x07);
1365                printk(KERN_INFO
1366                    "Winbond LPT Config: irqtype=%s, ECP fifo threshold=%d\n",
1367                                        irqtypes[crf0>>7], (crf0>>3)&0x0f);
1368                printk(KERN_INFO "Winbond LPT Config: Port mode=%s\n",
1369                                        modes[crf0 & 0x07]);
1370        }
1371
1372        if (cr30 & 0x01) { /* the settings can be interrogated later ... */
1373                s = find_free_superio();
1374                if (s == NULL)
1375                        printk(KERN_INFO "Super-IO: too many chips!\n");
1376                else {
1377                        s->io = (cr60 << 8) | cr61;
1378                        s->irq = cr70 & 0x0f;
1379                        s->dma = (((cr74 & 0x07) > 3) ?
1380                                           PARPORT_DMA_NONE : (cr74 & 0x07));
1381                }
1382        }
1383}
1384
1385static void __devinit decode_winbond(int efer, int key, int devid,
1386                                                        int devrev, int oldid)
1387{
1388        const char *type = "unknown";
1389        int id, progif = 2;
1390
1391        if (devid == devrev)
1392                /* simple heuristics, we happened to read some
1393                   non-winbond register */
1394                return;
1395
1396        id = (devid << 8) | devrev;
1397
1398        /* Values are from public data sheets pdf files, I can just
1399           confirm 83977TF is correct :-) */
1400        if (id == 0x9771)
1401                type = "83977F/AF";
1402        else if (id == 0x9773)
1403                type = "83977TF / SMSC 97w33x/97w34x";
1404        else if (id == 0x9774)
1405                type = "83977ATF";
1406        else if ((id & ~0x0f) == 0x5270)
1407                type = "83977CTF / SMSC 97w36x";
1408        else if ((id & ~0x0f) == 0x52f0)
1409                type = "83977EF / SMSC 97w35x";
1410        else if ((id & ~0x0f) == 0x5210)
1411                type = "83627";
1412        else if ((id & ~0x0f) == 0x6010)
1413                type = "83697HF";
1414        else if ((oldid & 0x0f) == 0x0a) {
1415                type = "83877F";
1416                progif = 1;
1417        } else if ((oldid & 0x0f) == 0x0b) {
1418                type = "83877AF";
1419                progif = 1;
1420        } else if ((oldid & 0x0f) == 0x0c) {
1421                type = "83877TF";
1422                progif = 1;
1423        } else if ((oldid & 0x0f) == 0x0d) {
1424                type = "83877ATF";
1425                progif = 1;
1426        } else
1427                progif = 0;
1428
1429        if (verbose_probing)
1430                printk(KERN_INFO "Winbond chip at EFER=0x%x key=0x%02x "
1431                       "devid=%02x devrev=%02x oldid=%02x type=%s\n",
1432                       efer, key, devid, devrev, oldid, type);
1433
1434        if (progif == 2)
1435                show_parconfig_winbond(efer, key);
1436}
1437
1438static void __devinit decode_smsc(int efer, int key, int devid, int devrev)
1439{
1440        const char *type = "unknown";
1441        void (*func)(int io, int key);
1442        int id;
1443
1444        if (devid == devrev)
1445                /* simple heuristics, we happened to read some
1446                   non-smsc register */
1447                return;
1448
1449        func = NULL;
1450        id = (devid << 8) | devrev;
1451
1452        if (id == 0x0302) {
1453                type = "37c669";
1454                func = show_parconfig_smsc37c669;
1455        } else if (id == 0x6582)
1456                type = "37c665IR";
1457        else if (devid == 0x65)
1458                type = "37c665GT";
1459        else if (devid == 0x66)
1460                type = "37c666GT";
1461
1462        if (verbose_probing)
1463                printk(KERN_INFO "SMSC chip at EFER=0x%x "
1464                       "key=0x%02x devid=%02x devrev=%02x type=%s\n",
1465                       efer, key, devid, devrev, type);
1466
1467        if (func)
1468                func(efer, key);
1469}
1470
1471
1472static void __devinit winbond_check(int io, int key)
1473{
1474        int origval, devid, devrev, oldid, x_devid, x_devrev, x_oldid;
1475
1476        if (!request_region(io, 3, __func__))
1477                return;
1478
1479        origval = inb(io); /* Save original value */
1480
1481        /* First probe without key */
1482        outb(0x20, io);
1483        x_devid = inb(io + 1);
1484        outb(0x21, io);
1485        x_devrev = inb(io + 1);
1486        outb(0x09, io);
1487        x_oldid = inb(io + 1);
1488
1489        outb(key, io);
1490        outb(key, io);     /* Write Magic Sequence to EFER, extended
1491                              function enable register */
1492        outb(0x20, io);    /* Write EFIR, extended function index register */
1493        devid = inb(io + 1);  /* Read EFDR, extended function data register */
1494        outb(0x21, io);
1495        devrev = inb(io + 1);
1496        outb(0x09, io);
1497        oldid = inb(io + 1);
1498        outb(0xaa, io);    /* Magic Seal */
1499
1500        outb(origval, io); /* in case we poked some entirely different hardware */
1501
1502        if ((x_devid == devid) && (x_devrev == devrev) && (x_oldid == oldid))
1503                goto out; /* protection against false positives */
1504
1505        decode_winbond(io, key, devid, devrev, oldid);
1506out:
1507        release_region(io, 3);
1508}
1509
1510static void __devinit winbond_check2(int io, int key)
1511{
1512        int origval[3], devid, devrev, oldid, x_devid, x_devrev, x_oldid;
1513
1514        if (!request_region(io, 3, __func__))
1515                return;
1516
1517        origval[0] = inb(io); /* Save original values */
1518        origval[1] = inb(io + 1);
1519        origval[2] = inb(io + 2);
1520
1521        /* First probe without the key */
1522        outb(0x20, io + 2);
1523        x_devid = inb(io + 2);
1524        outb(0x21, io + 1);
1525        x_devrev = inb(io + 2);
1526        outb(0x09, io + 1);
1527        x_oldid = inb(io + 2);
1528
1529        outb(key, io);     /* Write Magic Byte to EFER, extended
1530                              function enable register */
1531        outb(0x20, io + 2);  /* Write EFIR, extended function index register */
1532        devid = inb(io + 2);  /* Read EFDR, extended function data register */
1533        outb(0x21, io + 1);
1534        devrev = inb(io + 2);
1535        outb(0x09, io + 1);
1536        oldid = inb(io + 2);
1537        outb(0xaa, io);    /* Magic Seal */
1538
1539        outb(origval[0], io); /* in case we poked some entirely different hardware */
1540        outb(origval[1], io + 1);
1541        outb(origval[2], io + 2);
1542
1543        if (x_devid == devid && x_devrev == devrev && x_oldid == oldid)
1544                goto out; /* protection against false positives */
1545
1546        decode_winbond(io, key, devid, devrev, oldid);
1547out:
1548        release_region(io, 3);
1549}
1550
1551static void __devinit smsc_check(int io, int key)
1552{
1553        int origval, id, rev, oldid, oldrev, x_id, x_rev, x_oldid, x_oldrev;
1554
1555        if (!request_region(io, 3, __func__))
1556                return;
1557
1558        origval = inb(io); /* Save original value */
1559
1560        /* First probe without the key */
1561        outb(0x0d, io);
1562        x_oldid = inb(io + 1);
1563        outb(0x0e, io);
1564        x_oldrev = inb(io + 1);
1565        outb(0x20, io);
1566        x_id = inb(io + 1);
1567        outb(0x21, io);
1568        x_rev = inb(io + 1);
1569
1570        outb(key, io);
1571        outb(key, io);     /* Write Magic Sequence to EFER, extended
1572                              function enable register */
1573        outb(0x0d, io);    /* Write EFIR, extended function index register */
1574        oldid = inb(io + 1);  /* Read EFDR, extended function data register */
1575        outb(0x0e, io);
1576        oldrev = inb(io + 1);
1577        outb(0x20, io);
1578        id = inb(io + 1);
1579        outb(0x21, io);
1580        rev = inb(io + 1);
1581        outb(0xaa, io);    /* Magic Seal */
1582
1583        outb(origval, io); /* in case we poked some entirely different hardware */
1584
1585        if (x_id == id && x_oldrev == oldrev &&
1586            x_oldid == oldid && x_rev == rev)
1587                goto out; /* protection against false positives */
1588
1589        decode_smsc(io, key, oldid, oldrev);
1590out:
1591        release_region(io, 3);
1592}
1593
1594
1595static void __devinit detect_and_report_winbond(void)
1596{
1597        if (verbose_probing)
1598                printk(KERN_DEBUG "Winbond Super-IO detection, now testing ports 3F0,370,250,4E,2E ...\n");
1599        winbond_check(0x3f0, 0x87);
1600        winbond_check(0x370, 0x87);
1601        winbond_check(0x2e , 0x87);
1602        winbond_check(0x4e , 0x87);
1603        winbond_check(0x3f0, 0x86);
1604        winbond_check2(0x250, 0x88);
1605        winbond_check2(0x250, 0x89);
1606}
1607
1608static void __devinit detect_and_report_smsc(void)
1609{
1610        if (verbose_probing)
1611                printk(KERN_DEBUG "SMSC Super-IO detection, now testing Ports 2F0, 370 ...\n");
1612        smsc_check(0x3f0, 0x55);
1613        smsc_check(0x370, 0x55);
1614        smsc_check(0x3f0, 0x44);
1615        smsc_check(0x370, 0x44);
1616}
1617
1618static void __devinit detect_and_report_it87(void)
1619{
1620        u16 dev;
1621        u8 origval, r;
1622        if (verbose_probing)
1623                printk(KERN_DEBUG "IT8705 Super-IO detection, now testing port 2E ...\n");
1624        if (!request_muxed_region(0x2e, 2, __func__))
1625                return;
1626        origval = inb(0x2e);            /* Save original value */
1627        outb(0x87, 0x2e);
1628        outb(0x01, 0x2e);
1629        outb(0x55, 0x2e);
1630        outb(0x55, 0x2e);
1631        outb(0x20, 0x2e);
1632        dev = inb(0x2f) << 8;
1633        outb(0x21, 0x2e);
1634        dev |= inb(0x2f);
1635        if (dev == 0x8712 || dev == 0x8705 || dev == 0x8715 ||
1636            dev == 0x8716 || dev == 0x8718 || dev == 0x8726) {
1637                printk(KERN_INFO "IT%04X SuperIO detected.\n", dev);
1638                outb(0x07, 0x2E);       /* Parallel Port */
1639                outb(0x03, 0x2F);
1640                outb(0xF0, 0x2E);       /* BOOT 0x80 off */
1641                r = inb(0x2f);
1642                outb(0xF0, 0x2E);
1643                outb(r | 8, 0x2F);
1644                outb(0x02, 0x2E);       /* Lock */
1645                outb(0x02, 0x2F);
1646        } else {
1647                outb(origval, 0x2e);    /* Oops, sorry to disturb */
1648        }
1649        release_region(0x2e, 2);
1650}
1651#endif /* CONFIG_PARPORT_PC_SUPERIO */
1652
1653static struct superio_struct *find_superio(struct parport *p)
1654{
1655        int i;
1656        for (i = 0; i < NR_SUPERIOS; i++)
1657                if (superios[i].io != p->base)
1658                        return &superios[i];
1659        return NULL;
1660}
1661
1662static int get_superio_dma(struct parport *p)
1663{
1664        struct superio_struct *s = find_superio(p);
1665        if (s)
1666                return s->dma;
1667        return PARPORT_DMA_NONE;
1668}
1669
1670static int get_superio_irq(struct parport *p)
1671{
1672        struct superio_struct *s = find_superio(p);
1673        if (s)
1674                return s->irq;
1675        return PARPORT_IRQ_NONE;
1676}
1677
1678
1679/* --- Mode detection ------------------------------------- */
1680
1681/*
1682 * Checks for port existence, all ports support SPP MODE
1683 * Returns:
1684 *         0           :  No parallel port at this address
1685 *  PARPORT_MODE_PCSPP :  SPP port detected
1686 *                        (if the user specified an ioport himself,
1687 *                         this shall always be the case!)
1688 *
1689 */
1690static int parport_SPP_supported(struct parport *pb)
1691{
1692        unsigned char r, w;
1693
1694        /*
1695         * first clear an eventually pending EPP timeout
1696         * I (sailer@ife.ee.ethz.ch) have an SMSC chipset
1697         * that does not even respond to SPP cycles if an EPP
1698         * timeout is pending
1699         */
1700        clear_epp_timeout(pb);
1701
1702        /* Do a simple read-write test to make sure the port exists. */
1703        w = 0xc;
1704        outb(w, CONTROL(pb));
1705
1706        /* Is there a control register that we can read from?  Some
1707         * ports don't allow reads, so read_control just returns a
1708         * software copy. Some ports _do_ allow reads, so bypass the
1709         * software copy here.  In addition, some bits aren't
1710         * writable. */
1711        r = inb(CONTROL(pb));
1712        if ((r & 0xf) == w) {
1713                w = 0xe;
1714                outb(w, CONTROL(pb));
1715                r = inb(CONTROL(pb));
1716                outb(0xc, CONTROL(pb));
1717                if ((r & 0xf) == w)
1718                        return PARPORT_MODE_PCSPP;
1719        }
1720
1721        if (user_specified)
1722                /* That didn't work, but the user thinks there's a
1723                 * port here. */
1724                printk(KERN_INFO "parport 0x%lx (WARNING): CTR: "
1725                        "wrote 0x%02x, read 0x%02x\n", pb->base, w, r);
1726
1727        /* Try the data register.  The data lines aren't tri-stated at
1728         * this stage, so we expect back what we wrote. */
1729        w = 0xaa;
1730        parport_pc_write_data(pb, w);
1731        r = parport_pc_read_data(pb);
1732        if (r == w) {
1733                w = 0x55;
1734                parport_pc_write_data(pb, w);
1735                r = parport_pc_read_data(pb);
1736                if (r == w)
1737                        return PARPORT_MODE_PCSPP;
1738        }
1739
1740        if (user_specified) {
1741                /* Didn't work, but the user is convinced this is the
1742                 * place. */
1743                printk(KERN_INFO "parport 0x%lx (WARNING): DATA: "
1744                        "wrote 0x%02x, read 0x%02x\n", pb->base, w, r);
1745                printk(KERN_INFO "parport 0x%lx: You gave this address, "
1746                        "but there is probably no parallel port there!\n",
1747                        pb->base);
1748        }
1749
1750        /* It's possible that we can't read the control register or
1751         * the data register.  In that case just believe the user. */
1752        if (user_specified)
1753                return PARPORT_MODE_PCSPP;
1754
1755        return 0;
1756}
1757
1758/* Check for ECR
1759 *
1760 * Old style XT ports alias io ports every 0x400, hence accessing ECR
1761 * on these cards actually accesses the CTR.
1762 *
1763 * Modern cards don't do this but reading from ECR will return 0xff
1764 * regardless of what is written here if the card does NOT support
1765 * ECP.
1766 *
1767 * We first check to see if ECR is the same as CTR.  If not, the low
1768 * two bits of ECR aren't writable, so we check by writing ECR and
1769 * reading it back to see if it's what we expect.
1770 */
1771static int parport_ECR_present(struct parport *pb)
1772{
1773        struct parport_pc_private *priv = pb->private_data;
1774        unsigned char r = 0xc;
1775
1776        outb(r, CONTROL(pb));
1777        if ((inb(ECONTROL(pb)) & 0x3) == (r & 0x3)) {
1778                outb(r ^ 0x2, CONTROL(pb)); /* Toggle bit 1 */
1779
1780                r = inb(CONTROL(pb));
1781                if ((inb(ECONTROL(pb)) & 0x2) == (r & 0x2))
1782                        goto no_reg; /* Sure that no ECR register exists */
1783        }
1784
1785        if ((inb(ECONTROL(pb)) & 0x3) != 0x1)
1786                goto no_reg;
1787
1788        ECR_WRITE(pb, 0x34);
1789        if (inb(ECONTROL(pb)) != 0x35)
1790                goto no_reg;
1791
1792        priv->ecr = 1;
1793        outb(0xc, CONTROL(pb));
1794
1795        /* Go to mode 000 */
1796        frob_set_mode(pb, ECR_SPP);
1797
1798        return 1;
1799
1800 no_reg:
1801        outb(0xc, CONTROL(pb));
1802        return 0;
1803}
1804
1805#ifdef CONFIG_PARPORT_1284
1806/* Detect PS/2 support.
1807 *
1808 * Bit 5 (0x20) sets the PS/2 data direction; setting this high
1809 * allows us to read data from the data lines.  In theory we would get back
1810 * 0xff but any peripheral attached to the port may drag some or all of the
1811 * lines down to zero.  So if we get back anything that isn't the contents
1812 * of the data register we deem PS/2 support to be present.
1813 *
1814 * Some SPP ports have "half PS/2" ability - you can't turn off the line
1815 * drivers, but an external peripheral with sufficiently beefy drivers of
1816 * its own can overpower them and assert its own levels onto the bus, from
1817 * where they can then be read back as normal.  Ports with this property
1818 * and the right type of device attached are likely to fail the SPP test,
1819 * (as they will appear to have stuck bits) and so the fact that they might
1820 * be misdetected here is rather academic.
1821 */
1822
1823static int parport_PS2_supported(struct parport *pb)
1824{
1825        int ok = 0;
1826
1827        clear_epp_timeout(pb);
1828
1829        /* try to tri-state the buffer */
1830        parport_pc_data_reverse(pb);
1831
1832        parport_pc_write_data(pb, 0x55);
1833        if (parport_pc_read_data(pb) != 0x55)
1834                ok++;
1835
1836        parport_pc_write_data(pb, 0xaa);
1837        if (parport_pc_read_data(pb) != 0xaa)
1838                ok++;
1839
1840        /* cancel input mode */
1841        parport_pc_data_forward(pb);
1842
1843        if (ok) {
1844                pb->modes |= PARPORT_MODE_TRISTATE;
1845        } else {
1846                struct parport_pc_private *priv = pb->private_data;
1847                priv->ctr_writable &= ~0x20;
1848        }
1849
1850        return ok;
1851}
1852
1853#ifdef CONFIG_PARPORT_PC_FIFO
1854static int parport_ECP_supported(struct parport *pb)
1855{
1856        int i;
1857        int config, configb;
1858        int pword;
1859        struct parport_pc_private *priv = pb->private_data;
1860        /* Translate ECP intrLine to ISA irq value */
1861        static const int intrline[] = { 0, 7, 9, 10, 11, 14, 15, 5 };
1862
1863        /* If there is no ECR, we have no hope of supporting ECP. */
1864        if (!priv->ecr)
1865                return 0;
1866
1867        /* Find out FIFO depth */
1868        ECR_WRITE(pb, ECR_SPP << 5); /* Reset FIFO */
1869        ECR_WRITE(pb, ECR_TST << 5); /* TEST FIFO */
1870        for (i = 0; i < 1024 && !(inb(ECONTROL(pb)) & 0x02); i++)
1871                outb(0xaa, FIFO(pb));
1872
1873        /*
1874         * Using LGS chipset it uses ECR register, but
1875         * it doesn't support ECP or FIFO MODE
1876         */
1877        if (i == 1024) {
1878                ECR_WRITE(pb, ECR_SPP << 5);
1879                return 0;
1880        }
1881
1882        priv->fifo_depth = i;
1883        if (verbose_probing)
1884                printk(KERN_DEBUG "0x%lx: FIFO is %d bytes\n", pb->base, i);
1885
1886        /* Find out writeIntrThreshold */
1887        frob_econtrol(pb, 1<<2, 1<<2);
1888        frob_econtrol(pb, 1<<2, 0);
1889        for (i = 1; i <= priv->fifo_depth; i++) {
1890                inb(FIFO(pb));
1891                udelay(50);
1892                if (inb(ECONTROL(pb)) & (1<<2))
1893                        break;
1894        }
1895
1896        if (i <= priv->fifo_depth) {
1897                if (verbose_probing)
1898                        printk(KERN_DEBUG "0x%lx: writeIntrThreshold is %d\n",
1899                                pb->base, i);
1900        } else
1901                /* Number of bytes we know we can write if we get an
1902                   interrupt. */
1903                i = 0;
1904
1905        priv->writeIntrThreshold = i;
1906
1907        /* Find out readIntrThreshold */
1908        frob_set_mode(pb, ECR_PS2); /* Reset FIFO and enable PS2 */
1909        parport_pc_data_reverse(pb); /* Must be in PS2 mode */
1910        frob_set_mode(pb, ECR_TST); /* Test FIFO */
1911        frob_econtrol(pb, 1<<2, 1<<2);
1912        frob_econtrol(pb, 1<<2, 0);
1913        for (i = 1; i <= priv->fifo_depth; i++) {
1914                outb(0xaa, FIFO(pb));
1915                if (inb(ECONTROL(pb)) & (1<<2))
1916                        break;
1917        }
1918
1919        if (i <= priv->fifo_depth) {
1920                if (verbose_probing)
1921                        printk(KERN_INFO "0x%lx: readIntrThreshold is %d\n",
1922                                pb->base, i);
1923        } else
1924                /* Number of bytes we can read if we get an interrupt. */
1925                i = 0;
1926
1927        priv->readIntrThreshold = i;
1928
1929        ECR_WRITE(pb, ECR_SPP << 5); /* Reset FIFO */
1930        ECR_WRITE(pb, 0xf4); /* Configuration mode */
1931        config = inb(CONFIGA(pb));
1932        pword = (config >> 4) & 0x7;
1933        switch (pword) {
1934        case 0:
1935                pword = 2;
1936                printk(KERN_WARNING "0x%lx: Unsupported pword size!\n",
1937                        pb->base);
1938                break;
1939        case 2:
1940                pword = 4;
1941                printk(KERN_WARNING "0x%lx: Unsupported pword size!\n",
1942                        pb->base);
1943                break;
1944        default:
1945                printk(KERN_WARNING "0x%lx: Unknown implementation ID\n",
1946                        pb->base);
1947                /* Assume 1 */
1948        case 1:
1949                pword = 1;
1950        }
1951        priv->pword = pword;
1952
1953        if (verbose_probing) {
1954                printk(KERN_DEBUG "0x%lx: PWord is %d bits\n",
1955                        pb->base, 8 * pword);
1956
1957                printk(KERN_DEBUG "0x%lx: Interrupts are ISA-%s\n", pb->base,
1958                        config & 0x80 ? "Level" : "Pulses");
1959
1960                configb = inb(CONFIGB(pb));
1961                printk(KERN_DEBUG "0x%lx: ECP port cfgA=0x%02x cfgB=0x%02x\n",
1962                        pb->base, config, configb);
1963                printk(KERN_DEBUG "0x%lx: ECP settings irq=", pb->base);
1964                if ((configb >> 3) & 0x07)
1965                        printk("%d", intrline[(configb >> 3) & 0x07]);
1966                else
1967                        printk("<none or set by other means>");
1968                printk(" dma=");
1969                if ((configb & 0x03) == 0x00)
1970                        printk("<none or set by other means>\n");
1971                else
1972                        printk("%d\n", configb & 0x07);
1973        }
1974
1975        /* Go back to mode 000 */
1976        frob_set_mode(pb, ECR_SPP);
1977
1978        return 1;
1979}
1980#endif
1981
1982static int parport_ECPPS2_supported(struct parport *pb)
1983{
1984        const struct parport_pc_private *priv = pb->private_data;
1985        int result;
1986        unsigned char oecr;
1987
1988        if (!priv->ecr)
1989                return 0;
1990
1991        oecr = inb(ECONTROL(pb));
1992        ECR_WRITE(pb, ECR_PS2 << 5);
1993        result = parport_PS2_supported(pb);
1994        ECR_WRITE(pb, oecr);
1995        return result;
1996}
1997
1998/* EPP mode detection  */
1999
2000static int parport_EPP_supported(struct parport *pb)
2001{
2002        const struct parport_pc_private *priv = pb->private_data;
2003
2004        /*
2005         * Theory:
2006         *      Bit 0 of STR is the EPP timeout bit, this bit is 0
2007         *      when EPP is possible and is set high when an EPP timeout
2008         *      occurs (EPP uses the HALT line to stop the CPU while it does
2009         *      the byte transfer, an EPP timeout occurs if the attached
2010         *      device fails to respond after 10 micro seconds).
2011         *
2012         *      This bit is cleared by either reading it (National Semi)
2013         *      or writing a 1 to the bit (SMC, UMC, WinBond), others ???
2014         *      This bit is always high in non EPP modes.
2015         */
2016
2017        /* If EPP timeout bit clear then EPP available */
2018        if (!clear_epp_timeout(pb))
2019                return 0;  /* No way to clear timeout */
2020
2021        /* Check for Intel bug. */
2022        if (priv->ecr) {
2023                unsigned char i;
2024                for (i = 0x00; i < 0x80; i += 0x20) {
2025                        ECR_WRITE(pb, i);
2026                        if (clear_epp_timeout(pb)) {
2027                                /* Phony EPP in ECP. */
2028                                return 0;
2029                        }
2030                }
2031        }
2032
2033        pb->modes |= PARPORT_MODE_EPP;
2034
2035        /* Set up access functions to use EPP hardware. */
2036        pb->ops->epp_read_data = parport_pc_epp_read_data;
2037        pb->ops->epp_write_data = parport_pc_epp_write_data;
2038        pb->ops->epp_read_addr = parport_pc_epp_read_addr;
2039        pb->ops->epp_write_addr = parport_pc_epp_write_addr;
2040
2041        return 1;
2042}
2043
2044static int parport_ECPEPP_supported(struct parport *pb)
2045{
2046        struct parport_pc_private *priv = pb->private_data;
2047        int result;
2048        unsigned char oecr;
2049
2050        if (!priv->ecr)
2051                return 0;
2052
2053        oecr = inb(ECONTROL(pb));
2054        /* Search for SMC style EPP+ECP mode */
2055        ECR_WRITE(pb, 0x80);
2056        outb(0x04, CONTROL(pb));
2057        result = parport_EPP_supported(pb);
2058
2059        ECR_WRITE(pb, oecr);
2060
2061        if (result) {
2062                /* Set up access functions to use ECP+EPP hardware. */
2063                pb->ops->epp_read_data = parport_pc_ecpepp_read_data;
2064                pb->ops->epp_write_data = parport_pc_ecpepp_write_data;
2065                pb->ops->epp_read_addr = parport_pc_ecpepp_read_addr;
2066                pb->ops->epp_write_addr = parport_pc_ecpepp_write_addr;
2067        }
2068
2069        return result;
2070}
2071
2072#else /* No IEEE 1284 support */
2073
2074/* Don't bother probing for modes we know we won't use. */
2075static int __devinit parport_PS2_supported(struct parport *pb) { return 0; }
2076#ifdef CONFIG_PARPORT_PC_FIFO
2077static int parport_ECP_supported(struct parport *pb)
2078{
2079        return 0;
2080}
2081#endif
2082static int __devinit parport_EPP_supported(struct parport *pb)
2083{
2084        return 0;
2085}
2086
2087static int __devinit parport_ECPEPP_supported(struct parport *pb)
2088{
2089        return 0;
2090}
2091
2092static int __devinit parport_ECPPS2_supported(struct parport *pb)
2093{
2094        return 0;
2095}
2096
2097#endif /* No IEEE 1284 support */
2098
2099/* --- IRQ detection -------------------------------------- */
2100
2101/* Only if supports ECP mode */
2102static int programmable_irq_support(struct parport *pb)
2103{
2104        int irq, intrLine;
2105        unsigned char oecr = inb(ECONTROL(pb));
2106        static const int lookup[8] = {
2107                PARPORT_IRQ_NONE, 7, 9, 10, 11, 14, 15, 5
2108        };
2109
2110        ECR_WRITE(pb, ECR_CNF << 5); /* Configuration MODE */
2111
2112        intrLine = (inb(CONFIGB(pb)) >> 3) & 0x07;
2113        irq = lookup[intrLine];
2114
2115        ECR_WRITE(pb, oecr);
2116        return irq;
2117}
2118
2119static int irq_probe_ECP(struct parport *pb)
2120{
2121        int i;
2122        unsigned long irqs;
2123
2124        irqs = probe_irq_on();
2125
2126        ECR_WRITE(pb, ECR_SPP << 5); /* Reset FIFO */
2127        ECR_WRITE(pb, (ECR_TST << 5) | 0x04);
2128        ECR_WRITE(pb, ECR_TST << 5);
2129
2130        /* If Full FIFO sure that writeIntrThreshold is generated */
2131        for (i = 0; i < 1024 && !(inb(ECONTROL(pb)) & 0x02) ; i++)
2132                outb(0xaa, FIFO(pb));
2133
2134        pb->irq = probe_irq_off(irqs);
2135        ECR_WRITE(pb, ECR_SPP << 5);
2136
2137        if (pb->irq <= 0)
2138                pb->irq = PARPORT_IRQ_NONE;
2139
2140        return pb->irq;
2141}
2142
2143/*
2144 * This detection seems that only works in National Semiconductors
2145 * This doesn't work in SMC, LGS, and Winbond
2146 */
2147static int irq_probe_EPP(struct parport *pb)
2148{
2149#ifndef ADVANCED_DETECT
2150        return PARPORT_IRQ_NONE;
2151#else
2152        int irqs;
2153        unsigned char oecr;
2154
2155        if (pb->modes & PARPORT_MODE_PCECR)
2156                oecr = inb(ECONTROL(pb));
2157
2158        irqs = probe_irq_on();
2159
2160        if (pb->modes & PARPORT_MODE_PCECR)
2161                frob_econtrol(pb, 0x10, 0x10);
2162
2163        clear_epp_timeout(pb);
2164        parport_pc_frob_control(pb, 0x20, 0x20);
2165        parport_pc_frob_control(pb, 0x10, 0x10);
2166        clear_epp_timeout(pb);
2167
2168        /* Device isn't expecting an EPP read
2169         * and generates an IRQ.
2170         */
2171        parport_pc_read_epp(pb);
2172        udelay(20);
2173
2174        pb->irq = probe_irq_off(irqs);
2175        if (pb->modes & PARPORT_MODE_PCECR)
2176                ECR_WRITE(pb, oecr);
2177        parport_pc_write_control(pb, 0xc);
2178
2179        if (pb->irq <= 0)
2180                pb->irq = PARPORT_IRQ_NONE;
2181
2182        return pb->irq;
2183#endif /* Advanced detection */
2184}
2185
2186static int irq_probe_SPP(struct parport *pb)
2187{
2188        /* Don't even try to do this. */
2189        return PARPORT_IRQ_NONE;
2190}
2191
2192/* We will attempt to share interrupt requests since other devices
2193 * such as sound cards and network cards seem to like using the
2194 * printer IRQs.
2195 *
2196 * When ECP is available we can autoprobe for IRQs.
2197 * NOTE: If we can autoprobe it, we can register the IRQ.
2198 */
2199static int parport_irq_probe(struct parport *pb)
2200{
2201        struct parport_pc_private *priv = pb->private_data;
2202
2203        if (priv->ecr) {
2204                pb->irq = programmable_irq_support(pb);
2205
2206                if (pb->irq == PARPORT_IRQ_NONE)
2207                        pb->irq = irq_probe_ECP(pb);
2208        }
2209
2210        if ((pb->irq == PARPORT_IRQ_NONE) && priv->ecr &&
2211            (pb->modes & PARPORT_MODE_EPP))
2212                pb->irq = irq_probe_EPP(pb);
2213
2214        clear_epp_timeout(pb);
2215
2216        if (pb->irq == PARPORT_IRQ_NONE && (pb->modes & PARPORT_MODE_EPP))
2217                pb->irq = irq_probe_EPP(pb);
2218
2219        clear_epp_timeout(pb);
2220
2221        if (pb->irq == PARPORT_IRQ_NONE)
2222                pb->irq = irq_probe_SPP(pb);
2223
2224        if (pb->irq == PARPORT_IRQ_NONE)
2225                pb->irq = get_superio_irq(pb);
2226
2227        return pb->irq;
2228}
2229
2230/* --- DMA detection -------------------------------------- */
2231
2232/* Only if chipset conforms to ECP ISA Interface Standard */
2233static int programmable_dma_support(struct parport *p)
2234{
2235        unsigned char oecr = inb(ECONTROL(p));
2236        int dma;
2237
2238        frob_set_mode(p, ECR_CNF);
2239
2240        dma = inb(CONFIGB(p)) & 0x07;
2241        /* 000: Indicates jumpered 8-bit DMA if read-only.
2242           100: Indicates jumpered 16-bit DMA if read-only. */
2243        if ((dma & 0x03) == 0)
2244                dma = PARPORT_DMA_NONE;
2245
2246        ECR_WRITE(p, oecr);
2247        return dma;
2248}
2249
2250static int parport_dma_probe(struct parport *p)
2251{
2252        const struct parport_pc_private *priv = p->private_data;
2253        if (priv->ecr)          /* ask ECP chipset first */
2254                p->dma = programmable_dma_support(p);
2255        if (p->dma == PARPORT_DMA_NONE) {
2256                /* ask known Super-IO chips proper, although these
2257                   claim ECP compatible, some don't report their DMA
2258                   conforming to ECP standards */
2259                p->dma = get_superio_dma(p);
2260        }
2261
2262        return p->dma;
2263}
2264
2265/* --- Initialisation code -------------------------------- */
2266
2267static LIST_HEAD(ports_list);
2268static DEFINE_SPINLOCK(ports_lock);
2269
2270struct parport *parport_pc_probe_port(unsigned long int base,
2271                                      unsigned long int base_hi,
2272                                      int irq, int dma,
2273                                      struct device *dev,
2274                                      int irqflags)
2275{
2276        struct parport_pc_private *priv;
2277        struct parport_operations *ops;
2278        struct parport *p;
2279        int probedirq = PARPORT_IRQ_NONE;
2280        struct resource *base_res;
2281        struct resource *ECR_res = NULL;
2282        struct resource *EPP_res = NULL;
2283        struct platform_device *pdev = NULL;
2284
2285        if (!dev) {
2286                /* We need a physical device to attach to, but none was
2287                 * provided. Create our own. */
2288                pdev = platform_device_register_simple("parport_pc",
2289                                                       base, NULL, 0);
2290                if (IS_ERR(pdev))
2291                        return NULL;
2292                dev = &pdev->dev;
2293
2294                dev->coherent_dma_mask = DMA_BIT_MASK(24);
2295                dev->dma_mask = &dev->coherent_dma_mask;
2296        }
2297
2298        ops = kmalloc(sizeof(struct parport_operations), GFP_KERNEL);
2299        if (!ops)
2300                goto out1;
2301
2302        priv = kmalloc(sizeof(struct parport_pc_private), GFP_KERNEL);
2303        if (!priv)
2304                goto out2;
2305
2306        /* a misnomer, actually - it's allocate and reserve parport number */
2307        p = parport_register_port(base, irq, dma, ops);
2308        if (!p)
2309                goto out3;
2310
2311        base_res = request_region(base, 3, p->name);
2312        if (!base_res)
2313                goto out4;
2314
2315        memcpy(ops, &parport_pc_ops, sizeof(struct parport_operations));
2316        priv->ctr = 0xc;
2317        priv->ctr_writable = ~0x10;
2318        priv->ecr = 0;
2319        priv->fifo_depth = 0;
2320        priv->dma_buf = NULL;
2321        priv->dma_handle = 0;
2322        INIT_LIST_HEAD(&priv->list);
2323        priv->port = p;
2324
2325        p->dev = dev;
2326        p->base_hi = base_hi;
2327        p->modes = PARPORT_MODE_PCSPP | PARPORT_MODE_SAFEININT;
2328        p->private_data = priv;
2329
2330        if (base_hi) {
2331                ECR_res = request_region(base_hi, 3, p->name);
2332                if (ECR_res)
2333                        parport_ECR_present(p);
2334        }
2335
2336        if (base != 0x3bc) {
2337                EPP_res = request_region(base+0x3, 5, p->name);
2338                if (EPP_res)
2339                        if (!parport_EPP_supported(p))
2340                                parport_ECPEPP_supported(p);
2341        }
2342        if (!parport_SPP_supported(p))
2343                /* No port. */
2344                goto out5;
2345        if (priv->ecr)
2346                parport_ECPPS2_supported(p);
2347        else
2348                parport_PS2_supported(p);
2349
2350        p->size = (p->modes & PARPORT_MODE_EPP) ? 8 : 3;
2351
2352        printk(KERN_INFO "%s: PC-style at 0x%lx", p->name, p->base);
2353        if (p->base_hi && priv->ecr)
2354                printk(" (0x%lx)", p->base_hi);
2355        if (p->irq == PARPORT_IRQ_AUTO) {
2356                p->irq = PARPORT_IRQ_NONE;
2357                parport_irq_probe(p);
2358        } else if (p->irq == PARPORT_IRQ_PROBEONLY) {
2359                p->irq = PARPORT_IRQ_NONE;
2360                parport_irq_probe(p);
2361                probedirq = p->irq;
2362                p->irq = PARPORT_IRQ_NONE;
2363        }
2364        if (p->irq != PARPORT_IRQ_NONE) {
2365                printk(", irq %d", p->irq);
2366                priv->ctr_writable |= 0x10;
2367
2368                if (p->dma == PARPORT_DMA_AUTO) {
2369                        p->dma = PARPORT_DMA_NONE;
2370                        parport_dma_probe(p);
2371                }
2372        }
2373        if (p->dma == PARPORT_DMA_AUTO) /* To use DMA, giving the irq
2374                                           is mandatory (see above) */
2375                p->dma = PARPORT_DMA_NONE;
2376
2377#ifdef CONFIG_PARPORT_PC_FIFO
2378        if (parport_ECP_supported(p) &&
2379            p->dma != PARPORT_DMA_NOFIFO &&
2380            priv->fifo_depth > 0 && p->irq != PARPORT_IRQ_NONE) {
2381                p->modes |= PARPORT_MODE_ECP | PARPORT_MODE_COMPAT;
2382                p->ops->compat_write_data = parport_pc_compat_write_block_pio;
2383#ifdef CONFIG_PARPORT_1284
2384                p->ops->ecp_write_data = parport_pc_ecp_write_block_pio;
2385                /* currently broken, but working on it.. (FB) */
2386                /* p->ops->ecp_read_data = parport_pc_ecp_read_block_pio; */
2387#endif /* IEEE 1284 support */
2388                if (p->dma != PARPORT_DMA_NONE) {
2389                        printk(", dma %d", p->dma);
2390                        p->modes |= PARPORT_MODE_DMA;
2391                } else
2392                        printk(", using FIFO");
2393        } else
2394                /* We can't use the DMA channel after all. */
2395                p->dma = PARPORT_DMA_NONE;
2396#endif /* Allowed to use FIFO/DMA */
2397
2398        printk(" [");
2399
2400#define printmode(x) \
2401        {\
2402                if (p->modes & PARPORT_MODE_##x) {\
2403                        printk("%s%s", f ? "," : "", #x);\
2404                        f++;\
2405                } \
2406        }
2407
2408        {
2409                int f = 0;
2410                printmode(PCSPP);
2411                printmode(TRISTATE);
2412                printmode(COMPAT)
2413                printmode(EPP);
2414                printmode(ECP);
2415                printmode(DMA);
2416        }
2417#undef printmode
2418#ifndef CONFIG_PARPORT_1284
2419        printk("(,...)");
2420#endif /* CONFIG_PARPORT_1284 */
2421        printk("]\n");
2422        if (probedirq != PARPORT_IRQ_NONE)
2423                printk(KERN_INFO "%s: irq %d detected\n", p->name, probedirq);
2424
2425        /* If No ECP release the ports grabbed above. */
2426        if (ECR_res && (p->modes & PARPORT_MODE_ECP) == 0) {
2427                release_region(base_hi, 3);
2428                ECR_res = NULL;
2429        }
2430        /* Likewise for EEP ports */
2431        if (EPP_res && (p->modes & PARPORT_MODE_EPP) == 0) {
2432                release_region(base+3, 5);
2433                EPP_res = NULL;
2434        }
2435        if (p->irq != PARPORT_IRQ_NONE) {
2436                if (request_irq(p->irq, parport_irq_handler,
2437                                 irqflags, p->name, p)) {
2438                        printk(KERN_WARNING "%s: irq %d in use, "
2439                                "resorting to polled operation\n",
2440                                p->name, p->irq);
2441                        p->irq = PARPORT_IRQ_NONE;
2442                        p->dma = PARPORT_DMA_NONE;
2443                }
2444
2445#ifdef CONFIG_PARPORT_PC_FIFO
2446#ifdef HAS_DMA
2447                if (p->dma != PARPORT_DMA_NONE) {
2448                        if (request_dma(p->dma, p->name)) {
2449                                printk(KERN_WARNING "%s: dma %d in use, "
2450                                        "resorting to PIO operation\n",
2451                                        p->name, p->dma);
2452                                p->dma = PARPORT_DMA_NONE;
2453                        } else {
2454                                priv->dma_buf =
2455                                  dma_alloc_coherent(dev,
2456                                                       PAGE_SIZE,
2457                                                       &priv->dma_handle,
2458                                                       GFP_KERNEL);
2459                                if (!priv->dma_buf) {
2460                                        printk(KERN_WARNING "%s: "
2461                                                "cannot get buffer for DMA, "
2462                                                "resorting to PIO operation\n",
2463                                                p->name);
2464                                        free_dma(p->dma);
2465                                        p->dma = PARPORT_DMA_NONE;
2466                                }
2467                        }
2468                }
2469#endif
2470#endif
2471        }
2472
2473        /* Done probing.  Now put the port into a sensible start-up state. */
2474        if (priv->ecr)
2475                /*
2476                 * Put the ECP detected port in PS2 mode.
2477                 * Do this also for ports that have ECR but don't do ECP.
2478                 */
2479                ECR_WRITE(p, 0x34);
2480
2481        parport_pc_write_data(p, 0);
2482        parport_pc_data_forward(p);
2483
2484        /* Now that we've told the sharing engine about the port, and
2485           found out its characteristics, let the high-level drivers
2486           know about it. */
2487        spin_lock(&ports_lock);
2488        list_add(&priv->list, &ports_list);
2489        spin_unlock(&ports_lock);
2490        parport_announce_port(p);
2491
2492        return p;
2493
2494out5:
2495        if (ECR_res)
2496                release_region(base_hi, 3);
2497        if (EPP_res)
2498                release_region(base+0x3, 5);
2499        release_region(base, 3);
2500out4:
2501        parport_put_port(p);
2502out3:
2503        kfree(priv);
2504out2:
2505        kfree(ops);
2506out1:
2507        if (pdev)
2508                platform_device_unregister(pdev);
2509        return NULL;
2510}
2511EXPORT_SYMBOL(parport_pc_probe_port);
2512
2513void parport_pc_unregister_port(struct parport *p)
2514{
2515        struct parport_pc_private *priv = p->private_data;
2516        struct parport_operations *ops = p->ops;
2517
2518        parport_remove_port(p);
2519        spin_lock(&ports_lock);
2520        list_del_init(&priv->list);
2521        spin_unlock(&ports_lock);
2522#if defined(CONFIG_PARPORT_PC_FIFO) && defined(HAS_DMA)
2523        if (p->dma != PARPORT_DMA_NONE)
2524                free_dma(p->dma);
2525#endif
2526        if (p->irq != PARPORT_IRQ_NONE)
2527                free_irq(p->irq, p);
2528        release_region(p->base, 3);
2529        if (p->size > 3)
2530                release_region(p->base + 3, p->size - 3);
2531        if (p->modes & PARPORT_MODE_ECP)
2532                release_region(p->base_hi, 3);
2533#if defined(CONFIG_PARPORT_PC_FIFO) && defined(HAS_DMA)
2534        if (priv->dma_buf)
2535                dma_free_coherent(p->physport->dev, PAGE_SIZE,
2536                                    priv->dma_buf,
2537                                    priv->dma_handle);
2538#endif
2539        kfree(p->private_data);
2540        parport_put_port(p);
2541        kfree(ops); /* hope no-one cached it */
2542}
2543EXPORT_SYMBOL(parport_pc_unregister_port);
2544
2545#ifdef CONFIG_PCI
2546
2547/* ITE support maintained by Rich Liu <richliu@poorman.org> */
2548static int __devinit sio_ite_8872_probe(struct pci_dev *pdev, int autoirq,
2549                                         int autodma,
2550                                         const struct parport_pc_via_data *via)
2551{
2552        short inta_addr[6] = { 0x2A0, 0x2C0, 0x220, 0x240, 0x1E0 };
2553        u32 ite8872set;
2554        u32 ite8872_lpt, ite8872_lpthi;
2555        u8 ite8872_irq, type;
2556        int irq;
2557        int i;
2558
2559        DPRINTK(KERN_DEBUG "sio_ite_8872_probe()\n");
2560
2561        /* make sure which one chip */
2562        for (i = 0; i < 5; i++) {
2563                if (request_region(inta_addr[i], 32, "it887x")) {
2564                        int test;
2565                        pci_write_config_dword(pdev, 0x60,
2566                                                0xe5000000 | inta_addr[i]);
2567                        pci_write_config_dword(pdev, 0x78,
2568                                                0x00000000 | inta_addr[i]);
2569                        test = inb(inta_addr[i]);
2570                        if (test != 0xff)
2571                                break;
2572                        release_region(inta_addr[i], 32);
2573                }
2574        }
2575        if (i >= 5) {
2576                printk(KERN_INFO "parport_pc: cannot find ITE8872 INTA\n");
2577                return 0;
2578        }
2579
2580        type = inb(inta_addr[i] + 0x18);
2581        type &= 0x0f;
2582
2583        switch (type) {
2584        case 0x2:
2585                printk(KERN_INFO "parport_pc: ITE8871 found (1P)\n");
2586                ite8872set = 0x64200000;
2587                break;
2588        case 0xa:
2589                printk(KERN_INFO "parport_pc: ITE8875 found (1P)\n");
2590                ite8872set = 0x64200000;
2591                break;
2592        case 0xe:
2593                printk(KERN_INFO "parport_pc: ITE8872 found (2S1P)\n");
2594                ite8872set = 0x64e00000;
2595                break;
2596        case 0x6:
2597                printk(KERN_INFO "parport_pc: ITE8873 found (1S)\n");
2598                release_region(inta_addr[i], 32);
2599                return 0;
2600        case 0x8:
2601                printk(KERN_INFO "parport_pc: ITE8874 found (2S)\n");
2602                release_region(inta_addr[i], 32);
2603                return 0;
2604        default:
2605                printk(KERN_INFO "parport_pc: unknown ITE887x\n");
2606                printk(KERN_INFO "parport_pc: please mail 'lspci -nvv' "
2607                        "output to Rich.Liu@ite.com.tw\n");
2608                release_region(inta_addr[i], 32);
2609                return 0;
2610        }
2611
2612        pci_read_config_byte(pdev, 0x3c, &ite8872_irq);
2613        pci_read_config_dword(pdev, 0x1c, &ite8872_lpt);
2614        ite8872_lpt &= 0x0000ff00;
2615        pci_read_config_dword(pdev, 0x20, &ite8872_lpthi);
2616        ite8872_lpthi &= 0x0000ff00;
2617        pci_write_config_dword(pdev, 0x6c, 0xe3000000 | ite8872_lpt);
2618        pci_write_config_dword(pdev, 0x70, 0xe3000000 | ite8872_lpthi);
2619        pci_write_config_dword(pdev, 0x80, (ite8872_lpthi<<16) | ite8872_lpt);
2620        /* SET SPP&EPP , Parallel Port NO DMA , Enable All Function */
2621        /* SET Parallel IRQ */
2622        pci_write_config_dword(pdev, 0x9c,
2623                                ite8872set | (ite8872_irq * 0x11111));
2624
2625        DPRINTK(KERN_DEBUG "ITE887x: The IRQ is %d.\n", ite8872_irq);
2626        DPRINTK(KERN_DEBUG "ITE887x: The PARALLEL I/O port is 0x%x.\n",
2627                 ite8872_lpt);
2628        DPRINTK(KERN_DEBUG "ITE887x: The PARALLEL I/O porthi is 0x%x.\n",
2629                 ite8872_lpthi);
2630
2631        /* Let the user (or defaults) steer us away from interrupts */
2632        irq = ite8872_irq;
2633        if (autoirq != PARPORT_IRQ_AUTO)
2634                irq = PARPORT_IRQ_NONE;
2635
2636        /*
2637         * Release the resource so that parport_pc_probe_port can get it.
2638         */
2639        release_region(inta_addr[i], 32);
2640        if (parport_pc_probe_port(ite8872_lpt, ite8872_lpthi,
2641                                   irq, PARPORT_DMA_NONE, &pdev->dev, 0)) {
2642                printk(KERN_INFO
2643                        "parport_pc: ITE 8872 parallel port: io=0x%X",
2644                                                                ite8872_lpt);
2645                if (irq != PARPORT_IRQ_NONE)
2646                        printk(", irq=%d", irq);
2647                printk("\n");
2648                return 1;
2649        }
2650
2651        return 0;
2652}
2653
2654/* VIA 8231 support by Pavel Fedin <sonic_amiga@rambler.ru>
2655   based on VIA 686a support code by Jeff Garzik <jgarzik@pobox.com> */
2656static int __devinitdata parport_init_mode;
2657
2658/* Data for two known VIA chips */
2659static struct parport_pc_via_data via_686a_data __devinitdata = {
2660        0x51,
2661        0x50,
2662        0x85,
2663        0x02,
2664        0xE2,
2665        0xF0,
2666        0xE6
2667};
2668static struct parport_pc_via_data via_8231_data __devinitdata = {
2669        0x45,
2670        0x44,
2671        0x50,
2672        0x04,
2673        0xF2,
2674        0xFA,
2675        0xF6
2676};
2677
2678static int __devinit sio_via_probe(struct pci_dev *pdev, int autoirq,
2679                                    int autodma,
2680                                    const struct parport_pc_via_data *via)
2681{
2682        u8 tmp, tmp2, siofunc;
2683        u8 ppcontrol = 0;
2684        int dma, irq;
2685        unsigned port1, port2;
2686        unsigned have_epp = 0;
2687
2688        printk(KERN_DEBUG "parport_pc: VIA 686A/8231 detected\n");
2689
2690        switch (parport_init_mode) {
2691        case 1:
2692                printk(KERN_DEBUG "parport_pc: setting SPP mode\n");
2693                siofunc = VIA_FUNCTION_PARPORT_SPP;
2694                break;
2695        case 2:
2696                printk(KERN_DEBUG "parport_pc: setting PS/2 mode\n");
2697                siofunc = VIA_FUNCTION_PARPORT_SPP;
2698                ppcontrol = VIA_PARPORT_BIDIR;
2699                break;
2700        case 3:
2701                printk(KERN_DEBUG "parport_pc: setting EPP mode\n");
2702                siofunc = VIA_FUNCTION_PARPORT_EPP;
2703                ppcontrol = VIA_PARPORT_BIDIR;
2704                have_epp = 1;
2705                break;
2706        case 4:
2707                printk(KERN_DEBUG "parport_pc: setting ECP mode\n");
2708                siofunc = VIA_FUNCTION_PARPORT_ECP;
2709                ppcontrol = VIA_PARPORT_BIDIR;
2710                break;
2711        case 5:
2712                printk(KERN_DEBUG "parport_pc: setting EPP+ECP mode\n");
2713                siofunc = VIA_FUNCTION_PARPORT_ECP;
2714                ppcontrol = VIA_PARPORT_BIDIR|VIA_PARPORT_ECPEPP;
2715                have_epp = 1;
2716                break;
2717        default:
2718                printk(KERN_DEBUG
2719                        "parport_pc: probing current configuration\n");
2720                siofunc = VIA_FUNCTION_PROBE;
2721                break;
2722        }
2723        /*
2724         * unlock super i/o configuration
2725         */
2726        pci_read_config_byte(pdev, via->via_pci_superio_config_reg, &tmp);
2727        tmp |= via->via_pci_superio_config_data;
2728        pci_write_config_byte(pdev, via->via_pci_superio_config_reg, tmp);
2729
2730        /* Bits 1-0: Parallel Port Mode / Enable */
2731        outb(via->viacfg_function, VIA_CONFIG_INDEX);
2732        tmp = inb(VIA_CONFIG_DATA);
2733        /* Bit 5: EPP+ECP enable; bit 7: PS/2 bidirectional port enable */
2734        outb(via->viacfg_parport_control, VIA_CONFIG_INDEX);
2735        tmp2 = inb(VIA_CONFIG_DATA);
2736        if (siofunc == VIA_FUNCTION_PROBE) {
2737                siofunc = tmp & VIA_FUNCTION_PARPORT_DISABLE;
2738                ppcontrol = tmp2;
2739        } else {
2740                tmp &= ~VIA_FUNCTION_PARPORT_DISABLE;
2741                tmp |= siofunc;
2742                outb(via->viacfg_function, VIA_CONFIG_INDEX);
2743                outb(tmp, VIA_CONFIG_DATA);
2744                tmp2 &= ~(VIA_PARPORT_BIDIR|VIA_PARPORT_ECPEPP);
2745                tmp2 |= ppcontrol;
2746                outb(via->viacfg_parport_control, VIA_CONFIG_INDEX);
2747                outb(tmp2, VIA_CONFIG_DATA);
2748        }
2749
2750        /* Parallel Port I/O Base Address, bits 9-2 */
2751        outb(via->viacfg_parport_base, VIA_CONFIG_INDEX);
2752        port1 = inb(VIA_CONFIG_DATA) << 2;
2753
2754        printk(KERN_DEBUG "parport_pc: Current parallel port base: 0x%X\n",
2755                                                                        port1);
2756        if (port1 == 0x3BC && have_epp) {
2757                outb(via->viacfg_parport_base, VIA_CONFIG_INDEX);
2758                outb((0x378 >> 2), VIA_CONFIG_DATA);
2759                printk(KERN_DEBUG
2760                        "parport_pc: Parallel port base changed to 0x378\n");
2761                port1 = 0x378;
2762        }
2763
2764        /*
2765         * lock super i/o configuration
2766         */
2767        pci_read_config_byte(pdev, via->via_pci_superio_config_reg, &tmp);
2768        tmp &= ~via->via_pci_superio_config_data;
2769        pci_write_config_byte(pdev, via->via_pci_superio_config_reg, tmp);
2770
2771        if (siofunc == VIA_FUNCTION_PARPORT_DISABLE) {
2772                printk(KERN_INFO "parport_pc: VIA parallel port disabled in BIOS\n");
2773                return 0;
2774        }
2775
2776        /* Bits 7-4: PnP Routing for Parallel Port IRQ */
2777        pci_read_config_byte(pdev, via->via_pci_parport_irq_reg, &tmp);
2778        irq = ((tmp & VIA_IRQCONTROL_PARALLEL) >> 4);
2779
2780        if (siofunc == VIA_FUNCTION_PARPORT_ECP) {
2781                /* Bits 3-2: PnP Routing for Parallel Port DMA */
2782                pci_read_config_byte(pdev, via->via_pci_parport_dma_reg, &tmp);
2783                dma = ((tmp & VIA_DMACONTROL_PARALLEL) >> 2);
2784        } else
2785                /* if ECP not enabled, DMA is not enabled, assumed
2786                   bogus 'dma' value */
2787                dma = PARPORT_DMA_NONE;
2788
2789        /* Let the user (or defaults) steer us away from interrupts and DMA */
2790        if (autoirq == PARPORT_IRQ_NONE) {
2791                irq = PARPORT_IRQ_NONE;
2792                dma = PARPORT_DMA_NONE;
2793        }
2794        if (autodma == PARPORT_DMA_NONE)
2795                dma = PARPORT_DMA_NONE;
2796
2797        switch (port1) {
2798        case 0x3bc:
2799                port2 = 0x7bc; break;
2800        case 0x378:
2801                port2 = 0x778; break;
2802        case 0x278:
2803                port2 = 0x678; break;
2804        default:
2805                printk(KERN_INFO
2806                        "parport_pc: Weird VIA parport base 0x%X, ignoring\n",
2807                                                                        port1);
2808                return 0;
2809        }
2810
2811        /* filter bogus IRQs */
2812        switch (irq) {
2813        case 0:
2814        case 2:
2815        case 8:
2816        case 13:
2817                irq = PARPORT_IRQ_NONE;
2818                break;
2819
2820        default: /* do nothing */
2821                break;
2822        }
2823
2824        /* finally, do the probe with values obtained */
2825        if (parport_pc_probe_port(port1, port2, irq, dma, &pdev->dev, 0)) {
2826                printk(KERN_INFO
2827                        "parport_pc: VIA parallel port: io=0x%X", port1);
2828                if (irq != PARPORT_IRQ_NONE)
2829                        printk(", irq=%d", irq);
2830                if (dma != PARPORT_DMA_NONE)
2831                        printk(", dma=%d", dma);
2832                printk("\n");
2833                return 1;
2834        }
2835
2836        printk(KERN_WARNING "parport_pc: Strange, can't probe VIA parallel port: io=0x%X, irq=%d, dma=%d\n",
2837                port1, irq, dma);
2838        return 0;
2839}
2840
2841
2842enum parport_pc_sio_types {
2843        sio_via_686a = 0,   /* Via VT82C686A motherboard Super I/O */
2844        sio_via_8231,       /* Via VT8231 south bridge integrated Super IO */
2845        sio_ite_8872,
2846        last_sio
2847};
2848
2849/* each element directly indexed from enum list, above */
2850static struct parport_pc_superio {
2851        int (*probe) (struct pci_dev *pdev, int autoirq, int autodma,
2852                      const struct parport_pc_via_data *via);
2853        const struct parport_pc_via_data *via;
2854} parport_pc_superio_info[] __devinitdata = {
2855        { sio_via_probe, &via_686a_data, },
2856        { sio_via_probe, &via_8231_data, },
2857        { sio_ite_8872_probe, NULL, },
2858};
2859
2860enum parport_pc_pci_cards {
2861        siig_1p_10x = last_sio,
2862        siig_2p_10x,
2863        siig_1p_20x,
2864        siig_2p_20x,
2865        lava_parallel,
2866        lava_parallel_dual_a,
2867        lava_parallel_dual_b,
2868        boca_ioppar,
2869        plx_9050,
2870        timedia_4006a,
2871        timedia_4014,
2872        timedia_4008a,
2873        timedia_4018,
2874        timedia_9018a,
2875        syba_2p_epp,
2876        syba_1p_ecp,
2877        titan_010l,
2878        titan_1284p1,
2879        titan_1284p2,
2880        avlab_1p,
2881        avlab_2p,
2882        oxsemi_952,
2883        oxsemi_954,
2884        oxsemi_840,
2885        oxsemi_pcie_pport,
2886        aks_0100,
2887        mobility_pp,
2888        netmos_9705,
2889        netmos_9715,
2890        netmos_9755,
2891        netmos_9805,
2892        netmos_9815,
2893        netmos_9901,
2894        netmos_9865,
2895        quatech_sppxp100,
2896};
2897
2898
2899/* each element directly indexed from enum list, above
2900 * (but offset by last_sio) */
2901static struct parport_pc_pci {
2902        int numports;
2903        struct { /* BAR (base address registers) numbers in the config
2904                    space header */
2905                int lo;
2906                int hi;
2907                /* -1 if not there, >6 for offset-method (max BAR is 6) */
2908        } addr[4];
2909
2910        /* If set, this is called immediately after pci_enable_device.
2911         * If it returns non-zero, no probing will take place and the
2912         * ports will not be used. */
2913        int (*preinit_hook) (struct pci_dev *pdev, int autoirq, int autodma);
2914
2915        /* If set, this is called after probing for ports.  If 'failed'
2916         * is non-zero we couldn't use any of the ports. */
2917        void (*postinit_hook) (struct pci_dev *pdev, int failed);
2918} cards[] = {
2919        /* siig_1p_10x */               { 1, { { 2, 3 }, } },
2920        /* siig_2p_10x */               { 2, { { 2, 3 }, { 4, 5 }, } },
2921        /* siig_1p_20x */               { 1, { { 0, 1 }, } },
2922        /* siig_2p_20x */               { 2, { { 0, 1 }, { 2, 3 }, } },
2923        /* lava_parallel */             { 1, { { 0, -1 }, } },
2924        /* lava_parallel_dual_a */      { 1, { { 0, -1 }, } },
2925        /* lava_parallel_dual_b */      { 1, { { 0, -1 }, } },
2926        /* boca_ioppar */               { 1, { { 0, -1 }, } },
2927        /* plx_9050 */                  { 2, { { 4, -1 }, { 5, -1 }, } },
2928        /* timedia_4006a */             { 1, { { 0, -1 }, } },
2929        /* timedia_4014  */             { 2, { { 0, -1 }, { 2, -1 }, } },
2930        /* timedia_4008a */             { 1, { { 0, 1 }, } },
2931        /* timedia_4018  */             { 2, { { 0, 1 }, { 2, 3 }, } },
2932        /* timedia_9018a */             { 2, { { 0, 1 }, { 2, 3 }, } },
2933                                        /* SYBA uses fixed offsets in
2934                                           a 1K io window */
2935        /* syba_2p_epp AP138B */        { 2, { { 0, 0x078 }, { 0, 0x178 }, } },
2936        /* syba_1p_ecp W83787 */        { 1, { { 0, 0x078 }, } },
2937        /* titan_010l */                { 1, { { 3, -1 }, } },
2938        /* titan_1284p1 */              { 1, { { 0, 1 }, } },
2939        /* titan_1284p2 */              { 2, { { 0, 1 }, { 2, 3 }, } },
2940        /* avlab_1p             */      { 1, { { 0, 1}, } },
2941        /* avlab_2p             */      { 2, { { 0, 1}, { 2, 3 },} },
2942        /* The Oxford Semi cards are unusual: 954 doesn't support ECP,
2943         * and 840 locks up if you write 1 to bit 2! */
2944        /* oxsemi_952 */                { 1, { { 0, 1 }, } },
2945        /* oxsemi_954 */                { 1, { { 0, -1 }, } },
2946        /* oxsemi_840 */                { 1, { { 0, 1 }, } },
2947        /* oxsemi_pcie_pport */         { 1, { { 0, 1 }, } },
2948        /* aks_0100 */                  { 1, { { 0, -1 }, } },
2949        /* mobility_pp */               { 1, { { 0, 1 }, } },
2950
2951        /* The netmos entries below are untested */
2952        /* netmos_9705 */               { 1, { { 0, -1 }, } },
2953        /* netmos_9715 */               { 2, { { 0, 1 }, { 2, 3 },} },
2954        /* netmos_9755 */               { 2, { { 0, 1 }, { 2, 3 },} },
2955        /* netmos_9805 */               { 1, { { 0, -1 }, } },
2956        /* netmos_9815 */               { 2, { { 0, -1 }, { 2, -1 }, } },
2957        /* netmos_9901 */               { 1, { { 0, -1 }, } },
2958        /* netmos_9865 */               { 1, { { 0, -1 }, } },
2959        /* quatech_sppxp100 */          { 1, { { 0, 1 }, } },
2960};
2961
2962static const struct pci_device_id parport_pc_pci_tbl[] = {
2963        /* Super-IO onboard chips */
2964        { 0x1106, 0x0686, PCI_ANY_ID, PCI_ANY_ID, 0, 0, sio_via_686a },
2965        { 0x1106, 0x8231, PCI_ANY_ID, PCI_ANY_ID, 0, 0, sio_via_8231 },
2966        { PCI_VENDOR_ID_ITE, PCI_DEVICE_ID_ITE_8872,
2967          PCI_ANY_ID, PCI_ANY_ID, 0, 0, sio_ite_8872 },
2968
2969        /* PCI cards */
2970        { PCI_VENDOR_ID_SIIG, PCI_DEVICE_ID_SIIG_1P_10x,
2971          PCI_ANY_ID, PCI_ANY_ID, 0, 0, siig_1p_10x },
2972        { PCI_VENDOR_ID_SIIG, PCI_DEVICE_ID_SIIG_2P_10x,
2973          PCI_ANY_ID, PCI_ANY_ID, 0, 0, siig_2p_10x },
2974        { PCI_VENDOR_ID_SIIG, PCI_DEVICE_ID_SIIG_1P_20x,
2975          PCI_ANY_ID, PCI_ANY_ID, 0, 0, siig_1p_20x },
2976        { PCI_VENDOR_ID_SIIG, PCI_DEVICE_ID_SIIG_2P_20x,
2977          PCI_ANY_ID, PCI_ANY_ID, 0, 0, siig_2p_20x },
2978        { PCI_VENDOR_ID_LAVA, PCI_DEVICE_ID_LAVA_PARALLEL,
2979          PCI_ANY_ID, PCI_ANY_ID, 0, 0, lava_parallel },
2980        { PCI_VENDOR_ID_LAVA, PCI_DEVICE_ID_LAVA_DUAL_PAR_A,
2981          PCI_ANY_ID, PCI_ANY_ID, 0, 0, lava_parallel_dual_a },
2982        { PCI_VENDOR_ID_LAVA, PCI_DEVICE_ID_LAVA_DUAL_PAR_B,
2983          PCI_ANY_ID, PCI_ANY_ID, 0, 0, lava_parallel_dual_b },
2984        { PCI_VENDOR_ID_LAVA, PCI_DEVICE_ID_LAVA_BOCA_IOPPAR,
2985          PCI_ANY_ID, PCI_ANY_ID, 0, 0, boca_ioppar },
2986        { PCI_VENDOR_ID_PLX, PCI_DEVICE_ID_PLX_9050,
2987          PCI_SUBVENDOR_ID_EXSYS, PCI_SUBDEVICE_ID_EXSYS_4014, 0, 0, plx_9050 },
2988        /* PCI_VENDOR_ID_TIMEDIA/SUNIX has many differing cards ...*/
2989        { 0x1409, 0x7268, 0x1409, 0x0101, 0, 0, timedia_4006a },
2990        { 0x1409, 0x7268, 0x1409, 0x0102, 0, 0, timedia_4014 },
2991        { 0x1409, 0x7268, 0x1409, 0x0103, 0, 0, timedia_4008a },
2992        { 0x1409, 0x7268, 0x1409, 0x0104, 0, 0, timedia_4018 },
2993        { 0x1409, 0x7268, 0x1409, 0x9018, 0, 0, timedia_9018a },
2994        { PCI_VENDOR_ID_SYBA, PCI_DEVICE_ID_SYBA_2P_EPP,
2995          PCI_ANY_ID, PCI_ANY_ID, 0, 0, syba_2p_epp },
2996        { PCI_VENDOR_ID_SYBA, PCI_DEVICE_ID_SYBA_1P_ECP,
2997          PCI_ANY_ID, PCI_ANY_ID, 0, 0, syba_1p_ecp },
2998        { PCI_VENDOR_ID_TITAN, PCI_DEVICE_ID_TITAN_010L,
2999          PCI_ANY_ID, PCI_ANY_ID, 0, 0, titan_010l },
3000        { 0x9710, 0x9805, 0x1000, 0x0010, 0, 0, titan_1284p1 },
3001        { 0x9710, 0x9815, 0x1000, 0x0020, 0, 0, titan_1284p2 },
3002        /* PCI_VENDOR_ID_AVLAB/Intek21 has another bunch of cards ...*/
3003        /* AFAVLAB_TK9902 */
3004        { 0x14db, 0x2120, PCI_ANY_ID, PCI_ANY_ID, 0, 0, avlab_1p},
3005        { 0x14db, 0x2121, PCI_ANY_ID, PCI_ANY_ID, 0, 0, avlab_2p},
3006        { PCI_VENDOR_ID_OXSEMI, PCI_DEVICE_ID_OXSEMI_16PCI952PP,
3007          PCI_ANY_ID, PCI_ANY_ID, 0, 0, oxsemi_952 },
3008        { PCI_VENDOR_ID_OXSEMI, PCI_DEVICE_ID_OXSEMI_16PCI954PP,
3009          PCI_ANY_ID, PCI_ANY_ID, 0, 0, oxsemi_954 },
3010        { PCI_VENDOR_ID_OXSEMI, PCI_DEVICE_ID_OXSEMI_12PCI840,
3011          PCI_ANY_ID, PCI_ANY_ID, 0, 0, oxsemi_840 },
3012        { PCI_VENDOR_ID_OXSEMI, PCI_DEVICE_ID_OXSEMI_PCIe840,
3013          PCI_ANY_ID, PCI_ANY_ID, 0, 0, oxsemi_pcie_pport },
3014        { PCI_VENDOR_ID_OXSEMI, PCI_DEVICE_ID_OXSEMI_PCIe840_G,
3015          PCI_ANY_ID, PCI_ANY_ID, 0, 0, oxsemi_pcie_pport },
3016        { PCI_VENDOR_ID_OXSEMI, PCI_DEVICE_ID_OXSEMI_PCIe952_0,
3017          PCI_ANY_ID, PCI_ANY_ID, 0, 0, oxsemi_pcie_pport },
3018        { PCI_VENDOR_ID_OXSEMI, PCI_DEVICE_ID_OXSEMI_PCIe952_0_G,
3019          PCI_ANY_ID, PCI_ANY_ID, 0, 0, oxsemi_pcie_pport },
3020        { PCI_VENDOR_ID_OXSEMI, PCI_DEVICE_ID_OXSEMI_PCIe952_1,
3021          PCI_ANY_ID, PCI_ANY_ID, 0, 0, oxsemi_pcie_pport },
3022        { PCI_VENDOR_ID_OXSEMI, PCI_DEVICE_ID_OXSEMI_PCIe952_1_G,
3023          PCI_ANY_ID, PCI_ANY_ID, 0, 0, oxsemi_pcie_pport },
3024        { PCI_VENDOR_ID_OXSEMI, PCI_DEVICE_ID_OXSEMI_PCIe952_1_U,
3025          PCI_ANY_ID, PCI_ANY_ID, 0, 0, oxsemi_pcie_pport },
3026        { PCI_VENDOR_ID_OXSEMI, PCI_DEVICE_ID_OXSEMI_PCIe952_1_GU,
3027          PCI_ANY_ID, PCI_ANY_ID, 0, 0, oxsemi_pcie_pport },
3028        { PCI_VENDOR_ID_AKS, PCI_DEVICE_ID_AKS_ALADDINCARD,
3029          PCI_ANY_ID, PCI_ANY_ID, 0, 0, aks_0100 },
3030        { 0x14f2, 0x0121, PCI_ANY_ID, PCI_ANY_ID, 0, 0, mobility_pp },
3031        /* NetMos communication controllers */
3032        { PCI_VENDOR_ID_NETMOS, PCI_DEVICE_ID_NETMOS_9705,
3033          PCI_ANY_ID, PCI_ANY_ID, 0, 0, netmos_9705 },
3034        { PCI_VENDOR_ID_NETMOS, PCI_DEVICE_ID_NETMOS_9715,
3035          PCI_ANY_ID, PCI_ANY_ID, 0, 0, netmos_9715 },
3036        { PCI_VENDOR_ID_NETMOS, PCI_DEVICE_ID_NETMOS_9755,
3037          PCI_ANY_ID, PCI_ANY_ID, 0, 0, netmos_9755 },
3038        { PCI_VENDOR_ID_NETMOS, PCI_DEVICE_ID_NETMOS_9805,
3039          PCI_ANY_ID, PCI_ANY_ID, 0, 0, netmos_9805 },
3040        { PCI_VENDOR_ID_NETMOS, PCI_DEVICE_ID_NETMOS_9815,
3041          PCI_ANY_ID, PCI_ANY_ID, 0, 0, netmos_9815 },
3042        { PCI_VENDOR_ID_NETMOS, PCI_DEVICE_ID_NETMOS_9901,
3043          0xA000, 0x2000, 0, 0, netmos_9901 },
3044        { PCI_VENDOR_ID_NETMOS, PCI_DEVICE_ID_NETMOS_9865,
3045          0xA000, 0x1000, 0, 0, netmos_9865 },
3046        { PCI_VENDOR_ID_NETMOS, PCI_DEVICE_ID_NETMOS_9865,
3047          0xA000, 0x2000, 0, 0, netmos_9865 },
3048        /* Quatech SPPXP-100 Parallel port PCI ExpressCard */
3049        { PCI_VENDOR_ID_QUATECH, PCI_DEVICE_ID_QUATECH_SPPXP_100,
3050          PCI_ANY_ID, PCI_ANY_ID, 0, 0, quatech_sppxp100 },
3051        { 0, } /* terminate list */
3052};
3053MODULE_DEVICE_TABLE(pci, parport_pc_pci_tbl);
3054
3055struct pci_parport_data {
3056        int num;
3057        struct parport *ports[2];
3058};
3059
3060static int parport_pc_pci_probe(struct pci_dev *dev,
3061                                           const struct pci_device_id *id)
3062{
3063        int err, count, n, i = id->driver_data;
3064        struct pci_parport_data *data;
3065
3066        if (i < last_sio)
3067                /* This is an onboard Super-IO and has already been probed */
3068                return 0;
3069
3070        /* This is a PCI card */
3071        i -= last_sio;
3072        count = 0;
3073        err = pci_enable_device(dev);
3074        if (err)
3075                return err;
3076
3077        data = kmalloc(sizeof(struct pci_parport_data), GFP_KERNEL);
3078        if (!data)
3079                return -ENOMEM;
3080
3081        if (cards[i].preinit_hook &&
3082            cards[i].preinit_hook(dev, PARPORT_IRQ_NONE, PARPORT_DMA_NONE)) {
3083                kfree(data);
3084                return -ENODEV;
3085        }
3086
3087        for (n = 0; n < cards[i].numports; n++) {
3088                int lo = cards[i].addr[n].lo;
3089                int hi = cards[i].addr[n].hi;
3090                int irq;
3091                unsigned long io_lo, io_hi;
3092                io_lo = pci_resource_start(dev, lo);
3093                io_hi = 0;
3094                if ((hi >= 0) && (hi <= 6))
3095                        io_hi = pci_resource_start(dev, hi);
3096                else if (hi > 6)
3097                        io_lo += hi; /* Reinterpret the meaning of
3098                                        "hi" as an offset (see SYBA
3099                                        def.) */
3100                /* TODO: test if sharing interrupts works */
3101                irq = dev->irq;
3102                if (irq == IRQ_NONE) {
3103                        printk(KERN_DEBUG
3104        "PCI parallel port detected: %04x:%04x, I/O at %#lx(%#lx)\n",
3105                                parport_pc_pci_tbl[i + last_sio].vendor,
3106                                parport_pc_pci_tbl[i + last_sio].device,
3107                                io_lo, io_hi);
3108                        irq = PARPORT_IRQ_NONE;
3109                } else {
3110                        printk(KERN_DEBUG
3111        "PCI parallel port detected: %04x:%04x, I/O at %#lx(%#lx), IRQ %d\n",
3112                                parport_pc_pci_tbl[i + last_sio].vendor,
3113                                parport_pc_pci_tbl[i + last_sio].device,
3114                                io_lo, io_hi, irq);
3115                }
3116                data->ports[count] =
3117                        parport_pc_probe_port(io_lo, io_hi, irq,
3118                                               PARPORT_DMA_NONE, &dev->dev,
3119                                               IRQF_SHARED);
3120                if (data->ports[count])
3121                        count++;
3122        }
3123
3124        data->num = count;
3125
3126        if (cards[i].postinit_hook)
3127                cards[i].postinit_hook(dev, count == 0);
3128
3129        if (count) {
3130                pci_set_drvdata(dev, data);
3131                return 0;
3132        }
3133
3134        kfree(data);
3135
3136        return -ENODEV;
3137}
3138
3139static void __devexit parport_pc_pci_remove(struct pci_dev *dev)
3140{
3141        struct pci_parport_data *data = pci_get_drvdata(dev);
3142        int i;
3143
3144        pci_set_drvdata(dev, NULL);
3145
3146        if (data) {
3147                for (i = data->num - 1; i >= 0; i--)
3148                        parport_pc_unregister_port(data->ports[i]);
3149
3150                kfree(data);
3151        }
3152}
3153
3154static struct pci_driver parport_pc_pci_driver = {
3155        .name           = "parport_pc",
3156        .id_table       = parport_pc_pci_tbl,
3157        .probe          = parport_pc_pci_probe,
3158        .remove         = __devexit_p(parport_pc_pci_remove),
3159};
3160
3161static int __init parport_pc_init_superio(int autoirq, int autodma)
3162{
3163        const struct pci_device_id *id;
3164        struct pci_dev *pdev = NULL;
3165        int ret = 0;
3166
3167        for_each_pci_dev(pdev) {
3168                id = pci_match_id(parport_pc_pci_tbl, pdev);
3169                if (id == NULL || id->driver_data >= last_sio)
3170                        continue;
3171
3172                if (parport_pc_superio_info[id->driver_data].probe(
3173                        pdev, autoirq, autodma,
3174                        parport_pc_superio_info[id->driver_data].via)) {
3175                        ret++;
3176                }
3177        }
3178
3179        return ret; /* number of devices found */
3180}
3181#else
3182static struct pci_driver parport_pc_pci_driver;
3183static int __init parport_pc_init_superio(int autoirq, int autodma)
3184{
3185        return 0;
3186}
3187#endif /* CONFIG_PCI */
3188
3189#ifdef CONFIG_PNP
3190
3191static const struct pnp_device_id parport_pc_pnp_tbl[] = {
3192        /* Standard LPT Printer Port */
3193        {.id = "PNP0400", .driver_data = 0},
3194        /* ECP Printer Port */
3195        {.id = "PNP0401", .driver_data = 0},
3196        { }
3197};
3198
3199MODULE_DEVICE_TABLE(pnp, parport_pc_pnp_tbl);
3200
3201static int parport_pc_pnp_probe(struct pnp_dev *dev,
3202                                                const struct pnp_device_id *id)
3203{
3204        struct parport *pdata;
3205        unsigned long io_lo, io_hi;
3206        int dma, irq;
3207
3208        if (pnp_port_valid(dev, 0) &&
3209                !(pnp_port_flags(dev, 0) & IORESOURCE_DISABLED)) {
3210                io_lo = pnp_port_start(dev, 0);
3211        } else
3212                return -EINVAL;
3213
3214        if (pnp_port_valid(dev, 1) &&
3215                !(pnp_port_flags(dev, 1) & IORESOURCE_DISABLED)) {
3216                io_hi = pnp_port_start(dev, 1);
3217        } else
3218                io_hi = 0;
3219
3220        if (pnp_irq_valid(dev, 0) &&
3221                !(pnp_irq_flags(dev, 0) & IORESOURCE_DISABLED)) {
3222                irq = pnp_irq(dev, 0);
3223        } else
3224                irq = PARPORT_IRQ_NONE;
3225
3226        if (pnp_dma_valid(dev, 0) &&
3227                !(pnp_dma_flags(dev, 0) & IORESOURCE_DISABLED)) {
3228                dma = pnp_dma(dev, 0);
3229        } else
3230                dma = PARPORT_DMA_NONE;
3231
3232        dev_info(&dev->dev, "reported by %s\n", dev->protocol->name);
3233        pdata = parport_pc_probe_port(io_lo, io_hi, irq, dma, &dev->dev, 0);
3234        if (pdata == NULL)
3235                return -ENODEV;
3236
3237        pnp_set_drvdata(dev, pdata);
3238        return 0;
3239}
3240
3241static void parport_pc_pnp_remove(struct pnp_dev *dev)
3242{
3243        struct parport *pdata = (struct parport *)pnp_get_drvdata(dev);
3244        if (!pdata)
3245                return;
3246
3247        parport_pc_unregister_port(pdata);
3248}
3249
3250/* we only need the pnp layer to activate the device, at least for now */
3251static struct pnp_driver parport_pc_pnp_driver = {
3252        .name           = "parport_pc",
3253        .id_table       = parport_pc_pnp_tbl,
3254        .probe          = parport_pc_pnp_probe,
3255        .remove         = parport_pc_pnp_remove,
3256};
3257
3258#else
3259static struct pnp_driver parport_pc_pnp_driver;
3260#endif /* CONFIG_PNP */
3261
3262static int __devinit parport_pc_platform_probe(struct platform_device *pdev)
3263{
3264        /* Always succeed, the actual probing is done in
3265         * parport_pc_probe_port(). */
3266        return 0;
3267}
3268
3269static struct platform_driver parport_pc_platform_driver = {
3270        .driver = {
3271                .owner  = THIS_MODULE,
3272                .name   = "parport_pc",
3273        },
3274        .probe          = parport_pc_platform_probe,
3275};
3276
3277/* This is called by parport_pc_find_nonpci_ports (in asm/parport.h) */
3278static int __devinit __attribute__((unused))
3279parport_pc_find_isa_ports(int autoirq, int autodma)
3280{
3281        int count = 0;
3282
3283        if (parport_pc_probe_port(0x3bc, 0x7bc, autoirq, autodma, NULL, 0))
3284                count++;
3285        if (parport_pc_probe_port(0x378, 0x778, autoirq, autodma, NULL, 0))
3286                count++;
3287        if (parport_pc_probe_port(0x278, 0x678, autoirq, autodma, NULL, 0))
3288                count++;
3289
3290        return count;
3291}
3292
3293/* This function is called by parport_pc_init if the user didn't
3294 * specify any ports to probe.  Its job is to find some ports.  Order
3295 * is important here -- we want ISA ports to be registered first,
3296 * followed by PCI cards (for least surprise), but before that we want
3297 * to do chipset-specific tests for some onboard ports that we know
3298 * about.
3299 *
3300 * autoirq is PARPORT_IRQ_NONE, PARPORT_IRQ_AUTO, or PARPORT_IRQ_PROBEONLY
3301 * autodma is PARPORT_DMA_NONE or PARPORT_DMA_AUTO
3302 */
3303static void __init parport_pc_find_ports(int autoirq, int autodma)
3304{
3305        int count = 0, err;
3306
3307#ifdef CONFIG_PARPORT_PC_SUPERIO
3308        detect_and_report_it87();
3309        detect_and_report_winbond();
3310        detect_and_report_smsc();
3311#endif
3312
3313        /* Onboard SuperIO chipsets that show themselves on the PCI bus. */
3314        count += parport_pc_init_superio(autoirq, autodma);
3315
3316        /* PnP ports, skip detection if SuperIO already found them */
3317        if (!count) {
3318                err = pnp_register_driver(&parport_pc_pnp_driver);
3319                if (!err)
3320                        pnp_registered_parport = 1;
3321        }
3322
3323        /* ISA ports and whatever (see asm/parport.h). */
3324        parport_pc_find_nonpci_ports(autoirq, autodma);
3325
3326        err = pci_register_driver(&parport_pc_pci_driver);
3327        if (!err)
3328                pci_registered_parport = 1;
3329}
3330
3331/*
3332 *      Piles of crap below pretend to be a parser for module and kernel
3333 *      parameters.  Say "thank you" to whoever had come up with that
3334 *      syntax and keep in mind that code below is a cleaned up version.
3335 */
3336
3337static int __initdata io[PARPORT_PC_MAX_PORTS+1] = {
3338        [0 ... PARPORT_PC_MAX_PORTS] = 0
3339};
3340static int __initdata io_hi[PARPORT_PC_MAX_PORTS+1] = {
3341        [0 ... PARPORT_PC_MAX_PORTS] = PARPORT_IOHI_AUTO
3342};
3343static int __initdata dmaval[PARPORT_PC_MAX_PORTS] = {
3344        [0 ... PARPORT_PC_MAX_PORTS-1] = PARPORT_DMA_NONE
3345};
3346static int __initdata irqval[PARPORT_PC_MAX_PORTS] = {
3347        [0 ... PARPORT_PC_MAX_PORTS-1] = PARPORT_IRQ_PROBEONLY
3348};
3349
3350static int __init parport_parse_param(const char *s, int *val,
3351                                int automatic, int none, int nofifo)
3352{
3353        if (!s)
3354                return 0;
3355        if (!strncmp(s, "auto", 4))
3356                *val = automatic;
3357        else if (!strncmp(s, "none", 4))
3358                *val = none;
3359        else if (nofifo && !strncmp(s, "nofifo", 6))
3360                *val = nofifo;
3361        else {
3362                char *ep;
3363                unsigned long r = simple_strtoul(s, &ep, 0);
3364                if (ep != s)
3365                        *val = r;
3366                else {
3367                        printk(KERN_ERR "parport: bad specifier `%s'\n", s);
3368                        return -1;
3369                }
3370        }
3371        return 0;
3372}
3373
3374static int __init parport_parse_irq(const char *irqstr, int *val)
3375{
3376        return parport_parse_param(irqstr, val, PARPORT_IRQ_AUTO,
3377                                     PARPORT_IRQ_NONE, 0);
3378}
3379
3380static int __init parport_parse_dma(const char *dmastr, int *val)
3381{
3382        return parport_parse_param(dmastr, val, PARPORT_DMA_AUTO,
3383                                     PARPORT_DMA_NONE, PARPORT_DMA_NOFIFO);
3384}
3385
3386#ifdef CONFIG_PCI
3387static int __init parport_init_mode_setup(char *str)
3388{
3389        printk(KERN_DEBUG
3390             "parport_pc.c: Specified parameter parport_init_mode=%s\n", str);
3391
3392        if (!strcmp(str, "spp"))
3393                parport_init_mode = 1;
3394        if (!strcmp(str, "ps2"))
3395                parport_init_mode = 2;
3396        if (!strcmp(str, "epp"))
3397                parport_init_mode = 3;
3398        if (!strcmp(str, "ecp"))
3399                parport_init_mode = 4;
3400        if (!strcmp(str, "ecpepp"))
3401                parport_init_mode = 5;
3402        return 1;
3403}
3404#endif
3405
3406#ifdef MODULE
3407static char *irq[PARPORT_PC_MAX_PORTS];
3408static char *dma[PARPORT_PC_MAX_PORTS];
3409
3410MODULE_PARM_DESC(io, "Base I/O address (SPP regs)");
3411module_param_array(io, int, NULL, 0);
3412MODULE_PARM_DESC(io_hi, "Base I/O address (ECR)");
3413module_param_array(io_hi, int, NULL, 0);
3414MODULE_PARM_DESC(irq, "IRQ line");
3415module_param_array(irq, charp, NULL, 0);
3416MODULE_PARM_DESC(dma, "DMA channel");
3417module_param_array(dma, charp, NULL, 0);
3418#if defined(CONFIG_PARPORT_PC_SUPERIO) || \
3419       (defined(CONFIG_PARPORT_1284) && defined(CONFIG_PARPORT_PC_FIFO))
3420MODULE_PARM_DESC(verbose_probing, "Log chit-chat during initialisation");
3421module_param(verbose_probing, int, 0644);
3422#endif
3423#ifdef CONFIG_PCI
3424static char *init_mode;
3425MODULE_PARM_DESC(init_mode,
3426        "Initialise mode for VIA VT8231 port (spp, ps2, epp, ecp or ecpepp)");
3427module_param(init_mode, charp, 0);
3428#endif
3429
3430static int __init parse_parport_params(void)
3431{
3432        unsigned int i;
3433        int val;
3434
3435#ifdef CONFIG_PCI
3436        if (init_mode)
3437                parport_init_mode_setup(init_mode);
3438#endif
3439
3440        for (i = 0; i < PARPORT_PC_MAX_PORTS && io[i]; i++) {
3441                if (parport_parse_irq(irq[i], &val))
3442                        return 1;
3443                irqval[i] = val;
3444                if (parport_parse_dma(dma[i], &val))
3445                        return 1;
3446                dmaval[i] = val;
3447        }
3448        if (!io[0]) {
3449                /* The user can make us use any IRQs or DMAs we find. */
3450                if (irq[0] && !parport_parse_irq(irq[0], &val))
3451                        switch (val) {
3452                        case PARPORT_IRQ_NONE:
3453                        case PARPORT_IRQ_AUTO:
3454                                irqval[0] = val;
3455                                break;
3456                        default:
3457                                printk(KERN_WARNING
3458                                        "parport_pc: irq specified "
3459                                        "without base address.  Use 'io=' "
3460                                        "to specify one\n");
3461                        }
3462
3463                if (dma[0] && !parport_parse_dma(dma[0], &val))
3464                        switch (val) {
3465                        case PARPORT_DMA_NONE:
3466                        case PARPORT_DMA_AUTO:
3467                                dmaval[0] = val;
3468                                break;
3469                        default:
3470                                printk(KERN_WARNING
3471                                        "parport_pc: dma specified "
3472                                        "without base address.  Use 'io=' "
3473                                        "to specify one\n");
3474                        }
3475        }
3476        return 0;
3477}
3478
3479#else
3480
3481static int parport_setup_ptr __initdata;
3482
3483/*
3484 * Acceptable parameters:
3485 *
3486 * parport=0
3487 * parport=auto
3488 * parport=0xBASE[,IRQ[,DMA]]
3489 *
3490 * IRQ/DMA may be numeric or 'auto' or 'none'
3491 */
3492static int __init parport_setup(char *str)
3493{
3494        char *endptr;
3495        char *sep;
3496        int val;
3497
3498        if (!str || !*str || (*str == '0' && !*(str+1))) {
3499                /* Disable parport if "parport=0" in cmdline */
3500                io[0] = PARPORT_DISABLE;
3501                return 1;
3502        }
3503
3504        if (!strncmp(str, "auto", 4)) {
3505                irqval[0] = PARPORT_IRQ_AUTO;
3506                dmaval[0] = PARPORT_DMA_AUTO;
3507                return 1;
3508        }
3509
3510        val = simple_strtoul(str, &endptr, 0);
3511        if (endptr == str) {
3512                printk(KERN_WARNING "parport=%s not understood\n", str);
3513                return 1;
3514        }
3515
3516        if (parport_setup_ptr == PARPORT_PC_MAX_PORTS) {
3517                printk(KERN_ERR "parport=%s ignored, too many ports\n", str);
3518                return 1;
3519        }
3520
3521        io[parport_setup_ptr] = val;
3522        irqval[parport_setup_ptr] = PARPORT_IRQ_NONE;
3523        dmaval[parport_setup_ptr] = PARPORT_DMA_NONE;
3524
3525        sep = strchr(str, ',');
3526        if (sep++) {
3527                if (parport_parse_irq(sep, &val))
3528                        return 1;
3529                irqval[parport_setup_ptr] = val;
3530                sep = strchr(sep, ',');
3531                if (sep++) {
3532                        if (parport_parse_dma(sep, &val))
3533                                return 1;
3534                        dmaval[parport_setup_ptr] = val;
3535                }
3536        }
3537        parport_setup_ptr++;
3538        return 1;
3539}
3540
3541static int __init parse_parport_params(void)
3542{
3543        return io[0] == PARPORT_DISABLE;
3544}
3545
3546__setup("parport=", parport_setup);
3547
3548/*
3549 * Acceptable parameters:
3550 *
3551 * parport_init_mode=[spp|ps2|epp|ecp|ecpepp]
3552 */
3553#ifdef CONFIG_PCI
3554__setup("parport_init_mode=", parport_init_mode_setup);
3555#endif
3556#endif
3557
3558/* "Parser" ends here */
3559
3560static int __init parport_pc_init(void)
3561{
3562        int err;
3563
3564        if (parse_parport_params())
3565                return -EINVAL;
3566
3567        err = platform_driver_register(&parport_pc_platform_driver);
3568        if (err)
3569                return err;
3570
3571        if (io[0]) {
3572                int i;
3573                /* Only probe the ports we were given. */
3574                user_specified = 1;
3575                for (i = 0; i < PARPORT_PC_MAX_PORTS; i++) {
3576                        if (!io[i])
3577                                break;
3578                        if (io_hi[i] == PARPORT_IOHI_AUTO)
3579                                io_hi[i] = 0x400 + io[i];
3580                        parport_pc_probe_port(io[i], io_hi[i],
3581                                        irqval[i], dmaval[i], NULL, 0);
3582                }
3583        } else
3584                parport_pc_find_ports(irqval[0], dmaval[0]);
3585
3586        return 0;
3587}
3588
3589static void __exit parport_pc_exit(void)
3590{
3591        if (pci_registered_parport)
3592                pci_unregister_driver(&parport_pc_pci_driver);
3593        if (pnp_registered_parport)
3594                pnp_unregister_driver(&parport_pc_pnp_driver);
3595        platform_driver_unregister(&parport_pc_platform_driver);
3596
3597        while (!list_empty(&ports_list)) {
3598                struct parport_pc_private *priv;
3599                struct parport *port;
3600                priv = list_entry(ports_list.next,
3601                                  struct parport_pc_private, list);
3602                port = priv->port;
3603                if (port->dev && port->dev->bus == &platform_bus_type)
3604                        platform_device_unregister(
3605                                to_platform_device(port->dev));
3606                parport_pc_unregister_port(port);
3607        }
3608}
3609
3610MODULE_AUTHOR("Phil Blundell, Tim Waugh, others");
3611MODULE_DESCRIPTION("PC-style parallel port driver");
3612MODULE_LICENSE("GPL");
3613module_init(parport_pc_init)
3614module_exit(parport_pc_exit)
3615