#
# USB Host Controller Drivers
#
comment "USB Host Controller Drivers"
        depends on USB

config USB_C67X00_HCD
        tristate "Cypress C67x00 HCD support"
        depends on USB
        help
          The Cypress C67x00 (EZ-Host/EZ-OTG) chips are dual-role
          host/peripheral/OTG USB controllers.

          Enable this option to support this chip in host controller mode.
          If unsure, say N.

          To compile this driver as a module, choose M here: the
          module will be called c67x00.

config USB_XHCI_HCD
        tristate "xHCI HCD (USB 3.0) support (EXPERIMENTAL)"
        depends on USB && USB_ARCH_HAS_XHCI && EXPERIMENTAL
        ---help---
          The eXtensible Host Controller Interface (xHCI) is standard for USB 3.0
          "SuperSpeed" host controller hardware.

          To compile this driver as a module, choose M here: the
          module will be called xhci-hcd.

config USB_XHCI_HCD_DEBUGGING
        bool "Debugging for the xHCI host controller"
        depends on USB_XHCI_HCD
        ---help---
          Say 'Y' to turn on debugging for the xHCI host controller driver.
          This will spew debugging output, even in interrupt context.
          This should only be used for debugging xHCI driver bugs.

          If unsure, say N.

config USB_EHCI_HCD
        tristate "EHCI HCD (USB 2.0) support"
        depends on USB && USB_ARCH_HAS_EHCI
        ---help---
          The Enhanced Host Controller Interface (EHCI) is standard for USB 2.0
          "high speed" (480 Mbit/sec, 60 Mbyte/sec) host controller hardware.
          If your USB host controller supports USB 2.0, you will likely want to
          configure this Host Controller Driver.

          EHCI controllers are packaged with "companion" host controllers (OHCI
          or UHCI) to handle USB 1.1 devices connected to root hub ports.  Ports
          will connect to EHCI if the device is high speed, otherwise they
          connect to a companion controller.  If you configure EHCI, you should
          probably configure the OHCI (for NEC and some other vendors) USB Host
          Controller Driver or UHCI (for Via motherboards) Host Controller
          Driver too.

          You may want to read <file:Documentation/usb/ehci.txt>.

          To compile this driver as a module, choose M here: the
          module will be called ehci-hcd.

config USB_EHCI_ROOT_HUB_TT
        bool "Root Hub Transaction Translators"
        depends on USB_EHCI_HCD
        ---help---
          Some EHCI chips have vendor-specific extensions to integrate
          transaction translators, so that no OHCI or UHCI companion
          controller is needed.  It's safe to say "y" even if your
          controller doesn't support this feature.

          This supports the EHCI implementation that's originally
          from ARC, and has since changed hands a few times.

config USB_EHCI_TT_NEWSCHED
        bool "Improved Transaction Translator scheduling"
        depends on USB_EHCI_HCD
        default y
        ---help---
          This changes the periodic scheduling code to fill more of the low
          and full speed bandwidth available from the Transaction Translator
          (TT) in USB 2.0 hubs.  Without this, only one transfer will be
          issued in each microframe, significantly reducing the number of
          periodic low/fullspeed transfers possible.

          If you have multiple periodic low/fullspeed devices connected to a
          highspeed USB hub which is connected to a highspeed USB Host
          Controller, and some of those devices will not work correctly
          (possibly due to "ENOSPC" or "-28" errors), say Y.  Conversely, if
          you have only one such device and it doesn't work, you could try
          saying N.

          If unsure, say Y.

config USB_EHCI_HCD_PMC_MSP
        tristate "EHCI support for on-chip PMC MSP71xx USB controller"
        depends on USB_EHCI_HCD && MSP_HAS_USB
        default n
        select USB_EHCI_BIG_ENDIAN_DESC
        select USB_EHCI_BIG_ENDIAN_MMIO
        ---help---
                Enables support for the onchip USB controller on the PMC_MSP7100 Family SoC's.
                If unsure, say N.

config USB_EHCI_BIG_ENDIAN_MMIO
        bool
        depends on USB_EHCI_HCD && (PPC_CELLEB || PPC_PS3 || 440EPX || \
                                    ARCH_IXP4XX || XPS_USB_HCD_XILINX || \
                                    PPC_MPC512x || CPU_CAVIUM_OCTEON || \
                                    PMC_MSP || SPARC_LEON)
        default y

config USB_EHCI_BIG_ENDIAN_DESC
        bool
        depends on USB_EHCI_HCD && (440EPX || ARCH_IXP4XX || XPS_USB_HCD_XILINX || \
                                    PPC_MPC512x || PMC_MSP || SPARC_LEON)
        default y

config XPS_USB_HCD_XILINX
        bool "Use Xilinx usb host EHCI controller core"
        depends on USB_EHCI_HCD && (PPC32 || MICROBLAZE)
        select USB_EHCI_BIG_ENDIAN_DESC
        select USB_EHCI_BIG_ENDIAN_MMIO
        ---help---
                Xilinx xps USB host controller core is EHCI compilant and has
                transaction translator built-in. It can be configured to either
                support both high speed and full speed devices, or high speed
                devices only.

config USB_FSL_MPH_DR_OF
        tristate

config USB_EHCI_FSL
        bool "Support for Freescale on-chip EHCI USB controller"
        depends on USB_EHCI_HCD && FSL_SOC
        select USB_EHCI_ROOT_HUB_TT
        select USB_FSL_MPH_DR_OF if OF
        ---help---
          Variation of ARC USB block used in some Freescale chips.

config USB_EHCI_MXC
        bool "Support for Freescale on-chip EHCI USB controller"
        depends on USB_EHCI_HCD && ARCH_MXC
        select USB_EHCI_ROOT_HUB_TT
        ---help---
          Variation of ARC USB block used in some Freescale chips.

config USB_EHCI_HCD_OMAP
        bool "EHCI support for OMAP3 and later chips"
        depends on USB_EHCI_HCD && ARCH_OMAP
        default y
        --- help ---
          Enables support for the on-chip EHCI controller on
          OMAP3 and later chips.

config USB_EHCI_MSM
        bool "Support for MSM on-chip EHCI USB controller"
        depends on USB_EHCI_HCD && ARCH_MSM
        select USB_EHCI_ROOT_HUB_TT
        select USB_MSM_OTG
        ---help---
          Enables support for the USB Host controller present on the
          Qualcomm chipsets. Root Hub has inbuilt TT.
          This driver depends on OTG driver for PHY initialization,
          clock management, powering up VBUS, and power management.
          This driver is not supported on boards like trout which
          has an external PHY.

config USB_EHCI_TEGRA
       boolean "NVIDIA Tegra HCD support"
       depends on USB_EHCI_HCD && ARCH_TEGRA
       select USB_EHCI_ROOT_HUB_TT
       help
         This driver enables support for the internal USB Host Controllers
         found in NVIDIA Tegra SoCs. The controllers are EHCI compliant.

config USB_EHCI_HCD_PPC_OF
        bool "EHCI support for PPC USB controller on OF platform bus"
        depends on USB_EHCI_HCD && PPC_OF
        default y
        ---help---
          Enables support for the USB controller present on the PowerPC
          OpenFirmware platform bus.

config USB_EHCI_SH
        bool "EHCI support for SuperH USB controller"
        depends on USB_EHCI_HCD && SUPERH
        ---help---
          Enables support for the on-chip EHCI controller on the SuperH.
          If you use the PCI EHCI controller, this option is not necessary.

config USB_EHCI_S5P
       boolean "S5P EHCI support"
       depends on USB_EHCI_HCD && PLAT_S5P
       help
         Enable support for the S5P SOC's on-chip EHCI controller.

config USB_W90X900_EHCI
        bool "W90X900(W90P910) EHCI support"
        depends on USB_EHCI_HCD && ARCH_W90X900
        ---help---
                Enables support for the W90X900 USB controller

config USB_CNS3XXX_EHCI
        bool "Cavium CNS3XXX EHCI Module"
        depends on USB_EHCI_HCD && ARCH_CNS3XXX
        ---help---
          Enable support for the CNS3XXX SOC's on-chip EHCI controller.
          It is needed for high-speed (480Mbit/sec) USB 2.0 device
          support.

config USB_EHCI_ATH79
        bool "EHCI support for AR7XXX/AR9XXX SoCs"
        depends on USB_EHCI_HCD && (SOC_AR71XX || SOC_AR724X || SOC_AR913X)
        select USB_EHCI_ROOT_HUB_TT
        default y
        ---help---
          Enables support for the built-in EHCI controller present
          on the Atheros AR7XXX/AR9XXX SoCs.

config USB_OXU210HP_HCD
        tristate "OXU210HP HCD support"
        depends on USB
        ---help---
          The OXU210HP is an USB host/OTG/device controller. Enable this
          option if your board has this chip. If unsure, say N.

          This driver does not support isochronous transfers and doesn't
          implement OTG nor USB device controllers.

          To compile this driver as a module, choose M here: the
          module will be called oxu210hp-hcd.

config USB_ISP116X_HCD
        tristate "ISP116X HCD support"
        depends on USB
        ---help---
          The ISP1160 and ISP1161 chips are USB host controllers. Enable this
          option if your board has this chip. If unsure, say N.

          This driver does not support isochronous transfers.

          To compile this driver as a module, choose M here: the
          module will be called isp116x-hcd.

config USB_ISP1760_HCD
        tristate "ISP 1760 HCD support"
        depends on USB && EXPERIMENTAL
        ---help---
          The ISP1760 chip is a USB 2.0 host controller.

          This driver does not support isochronous transfers or OTG.
          This USB controller is usually attached to a non-DMA-Master
          capable bus. NXP's eval kit brings this chip on PCI card
          where the chip itself is behind a PLB to simulate such
          a bus.

          To compile this driver as a module, choose M here: the
          module will be called isp1760.

config USB_ISP1362_HCD
        tristate "ISP1362 HCD support"
        depends on USB
        default N
        ---help---
          Supports the Philips ISP1362 chip as a host controller

          This driver does not support isochronous transfers.

          To compile this driver as a module, choose M here: the
          module will be called isp1362-hcd.

config USB_OHCI_HCD
        tristate "OHCI HCD support"
        depends on USB && USB_ARCH_HAS_OHCI
        select ISP1301_OMAP if MACH_OMAP_H2 || MACH_OMAP_H3
        select USB_OTG_UTILS if ARCH_OMAP
        ---help---
          The Open Host Controller Interface (OHCI) is a standard for accessing
          USB 1.1 host controller hardware.  It does more in hardware than Intel's
          UHCI specification.  If your USB host controller follows the OHCI spec,
          say Y.  On most non-x86 systems, and on x86 hardware that's not using a
          USB controller from Intel or VIA, this is appropriate.  If your host
          controller doesn't use PCI, this is probably appropriate.  For a PCI
          based system where you're not sure, the "lspci -v" entry will list the
          right "prog-if" for your USB controller(s):  EHCI, OHCI, or UHCI.

          To compile this driver as a module, choose M here: the
          module will be called ohci-hcd.

config USB_OHCI_HCD_OMAP1
        bool "OHCI support for OMAP1/2 chips"
        depends on USB_OHCI_HCD && (ARCH_OMAP1 || ARCH_OMAP2)
        default y
        ---help---
          Enables support for the OHCI controller on OMAP1/2 chips.

config USB_OHCI_HCD_OMAP3
        bool "OHCI support for OMAP3 and later chips"
        depends on USB_OHCI_HCD && (ARCH_OMAP3 || ARCH_OMAP4)
        default y
        ---help---
          Enables support for the on-chip OHCI controller on
          OMAP3 and later chips.

config USB_OHCI_ATH79
        bool "USB OHCI support for the Atheros AR71XX/AR7240 SoCs"
        depends on USB_OHCI_HCD && (SOC_AR71XX || SOC_AR724X)
        default y
        help
          Enables support for the built-in OHCI controller present on the
          Atheros AR71XX/AR7240 SoCs.

config USB_OHCI_HCD_PPC_SOC
        bool "OHCI support for on-chip PPC USB controller"
        depends on USB_OHCI_HCD && (STB03xxx || PPC_MPC52xx)
        default y
        select USB_OHCI_BIG_ENDIAN_DESC
        select USB_OHCI_BIG_ENDIAN_MMIO
        ---help---
          Enables support for the USB controller on the MPC52xx or
          STB03xxx processor chip.  If unsure, say Y.

config USB_OHCI_HCD_PPC_OF_BE
        bool "OHCI support for OF platform bus (big endian)"
        depends on USB_OHCI_HCD && PPC_OF
        select USB_OHCI_BIG_ENDIAN_DESC
        select USB_OHCI_BIG_ENDIAN_MMIO
        ---help---
          Enables support for big-endian USB controllers present on the
          OpenFirmware platform bus.

config USB_OHCI_HCD_PPC_OF_LE
        bool "OHCI support for OF platform bus (little endian)"
        depends on USB_OHCI_HCD && PPC_OF
        select USB_OHCI_LITTLE_ENDIAN
        ---help---
          Enables support for little-endian USB controllers present on the
          OpenFirmware platform bus.

config USB_OHCI_HCD_PPC_OF
        bool
        depends on USB_OHCI_HCD && PPC_OF
        default USB_OHCI_HCD_PPC_OF_BE || USB_OHCI_HCD_PPC_OF_LE

config USB_OHCI_HCD_PCI
        bool "OHCI support for PCI-bus USB controllers"
        depends on USB_OHCI_HCD && PCI && (STB03xxx || PPC_MPC52xx || USB_OHCI_HCD_PPC_OF)
        default y
        select USB_OHCI_LITTLE_ENDIAN
        ---help---
          Enables support for PCI-bus plug-in USB controller cards.
          If unsure, say Y.

config USB_OHCI_HCD_SSB
        bool "OHCI support for Broadcom SSB OHCI core"
        depends on USB_OHCI_HCD && (SSB = y || SSB = USB_OHCI_HCD) && EXPERIMENTAL
        default n
        ---help---
          Support for the Sonics Silicon Backplane (SSB) attached
          Broadcom USB OHCI core.

          This device is present in some embedded devices with
          Broadcom based SSB bus.

          If unsure, say N.

config USB_OHCI_SH
        bool "OHCI support for SuperH USB controller"
        depends on USB_OHCI_HCD && SUPERH
        ---help---
          Enables support for the on-chip OHCI controller on the SuperH.
          If you use the PCI OHCI controller, this option is not necessary.

config USB_CNS3XXX_OHCI
        bool "Cavium CNS3XXX OHCI Module"
        depends on USB_OHCI_HCD && ARCH_CNS3XXX
        ---help---
          Enable support for the CNS3XXX SOC's on-chip OHCI controller.
          It is needed for low-speed USB 1.0 device support.

config USB_OHCI_BIG_ENDIAN_DESC
        bool
        depends on USB_OHCI_HCD
        default n

config USB_OHCI_BIG_ENDIAN_MMIO
        bool
        depends on USB_OHCI_HCD
        default n

config USB_OHCI_LITTLE_ENDIAN
        bool
        depends on USB_OHCI_HCD
        default n if STB03xxx || PPC_MPC52xx
        default y

config USB_UHCI_HCD
        tristate "UHCI HCD (most Intel and VIA) support"
        depends on USB && (PCI || SPARC_LEON)
        ---help---
          The Universal Host Controller Interface is a standard by Intel for
          accessing the USB hardware in the PC (which is also called the USB
          host controller). If your USB host controller conforms to this
          standard, you may want to say Y, but see below. All recent boards
          with Intel PCI chipsets (like intel 430TX, 440FX, 440LX, 440BX,
          i810, i820) conform to this standard. Also all VIA PCI chipsets
          (like VIA VP2, VP3, MVP3, Apollo Pro, Apollo Pro II or Apollo Pro
          133) and LEON/GRLIB SoCs with the GRUSBHC controller.
          If unsure, say Y.

          To compile this driver as a module, choose M here: the
          module will be called uhci-hcd.

config USB_UHCI_SUPPORT_NON_PCI_HC
        bool
        depends on USB_UHCI_HCD
        default y if SPARC_LEON

config USB_UHCI_BIG_ENDIAN_MMIO
        bool
        depends on USB_UHCI_SUPPORT_NON_PCI_HC && SPARC_LEON
        default y

config USB_UHCI_BIG_ENDIAN_DESC
        bool
        depends on USB_UHCI_SUPPORT_NON_PCI_HC && SPARC_LEON
        default y

config USB_FHCI_HCD
        tristate "Freescale QE USB Host Controller support"
        depends on USB && OF_GPIO && QE_GPIO && QUICC_ENGINE
        select FSL_GTM
        select QE_USB
        help
          This driver enables support for Freescale QE USB Host Controller
          (as found on MPC8360 and MPC8323 processors), the driver supports
          Full and Low Speed USB.

config FHCI_DEBUG
        bool "Freescale QE USB Host Controller debug support"
        depends on USB_FHCI_HCD && DEBUG_FS
        help
          Say "y" to see some FHCI debug information and statistics
          through debugfs.

config USB_U132_HCD
        tristate "Elan U132 Adapter Host Controller"
        depends on USB && USB_FTDI_ELAN
        default M
        help
          The U132 adapter is a USB to CardBus adapter specifically designed
          for PC cards that contain an OHCI host controller. Typical PC cards
          are the Orange Mobile 3G Option GlobeTrotter Fusion card. The U132
          adapter will *NOT* work with PC cards that do not contain an OHCI
          controller.

          For those PC cards that contain multiple OHCI controllers only the
          first one is used.

          The driver consists of two modules, the "ftdi-elan" module is a
          USB client driver that interfaces to the FTDI chip within ELAN's
          USB-to-PCMCIA adapter, and this "u132-hcd" module is a USB host
          controller driver that talks to the OHCI controller within the
          CardBus cards that are inserted in the U132 adapter.

          This driver has been tested with a CardBus OHCI USB adapter, and
          worked with a USB PEN Drive inserted into the first USB port of
          the PCCARD. A rather pointless thing to do, but useful for testing.

          It is safe to say M here.

          See also <http://www.elandigitalsystems.com/support/ufaq/u132linux.php>

config USB_SL811_HCD
        tristate "SL811HS HCD support"
        depends on USB
        help
          The SL811HS is a single-port USB controller that supports either
          host side or peripheral side roles.  Enable this option if your
          board has this chip, and you want to use it as a host controller. 
          If unsure, say N.

          To compile this driver as a module, choose M here: the
          module will be called sl811-hcd.

config USB_SL811_HCD_ISO
        bool "partial ISO support"
        depends on USB_SL811_HCD
        help
          The driver doesn't support iso_frame_desc (yet), but for some simple
          devices that just queue one ISO frame per URB, then ISO transfers
          "should" work using the normal urb status fields.

          If unsure, say N.

config USB_SL811_CS
        tristate "CF/PCMCIA support for SL811HS HCD"
        depends on USB_SL811_HCD && PCMCIA
        help
          Wraps a PCMCIA driver around the SL811HS HCD, supporting the RATOC
          REX-CFU1U CF card (often used with PDAs).  If unsure, say N.

          To compile this driver as a module, choose M here: the
          module will be called "sl811_cs".

config USB_R8A66597_HCD
        tristate "R8A66597 HCD support"
        depends on USB
        help
          The R8A66597 is a USB 2.0 host and peripheral controller.

          Enable this option if your board has this chip, and you want
          to use it as a host controller.  If unsure, say N.

          To compile this driver as a module, choose M here: the
          module will be called r8a66597-hcd.

config USB_RENESAS_USBHS_HCD
        tristate "Renesas USBHS HCD support"
        depends on USB
        depends on USB_RENESAS_USBHS
        help
          The Renesas USBHS is a USB 2.0 host and peripheral controller.

          Enable this option if your board has this chip, and you want
          to use it as a host controller.  If unsure, say N.

          To compile this driver as a module, choose M here: the
          module will be called renesas-usbhs.

config USB_WHCI_HCD
        tristate "Wireless USB Host Controller Interface (WHCI) driver (EXPERIMENTAL)"
        depends on EXPERIMENTAL
        depends on PCI && USB
        select USB_WUSB
        select UWB_WHCI
        help
          A driver for PCI-based Wireless USB Host Controllers that are
          compliant with the WHCI specification.

          To compile this driver a module, choose M here: the module
          will be called "whci-hcd".

config USB_HWA_HCD
        tristate "Host Wire Adapter (HWA) driver (EXPERIMENTAL)"
        depends on EXPERIMENTAL
        depends on USB
        select USB_WUSB
        select UWB_HWA
        help
          This driver enables you to connect Wireless USB devices to
          your system using a Host Wire Adaptor USB dongle. This is an
          UWB Radio Controller and WUSB Host Controller connected to
          your machine via USB (specified in WUSB1.0).

          To compile this driver a module, choose M here: the module
          will be called "hwa-hc".

config USB_IMX21_HCD
       tristate "i.MX21 HCD support"
       depends on USB && ARM && ARCH_MXC
       help
         This driver enables support for the on-chip USB host in the
         i.MX21 processor.

         To compile this driver as a module, choose M here: the
         module will be called "imx21-hcd".

config USB_OCTEON_EHCI
        bool "Octeon on-chip EHCI support"
        depends on USB && USB_EHCI_HCD && CPU_CAVIUM_OCTEON
        default n
        select USB_EHCI_BIG_ENDIAN_MMIO
        help
          Enable support for the Octeon II SOC's on-chip EHCI
          controller.  It is needed for high-speed (480Mbit/sec)
          USB 2.0 device support.  All CN6XXX based chips with USB are
          supported.

config USB_OCTEON_OHCI
        bool "Octeon on-chip OHCI support"
        depends on USB && USB_OHCI_HCD && CPU_CAVIUM_OCTEON
        default USB_OCTEON_EHCI
        select USB_OHCI_BIG_ENDIAN_MMIO
        select USB_OHCI_LITTLE_ENDIAN
        help
          Enable support for the Octeon II SOC's on-chip OHCI
          controller.  It is needed for low-speed USB 1.0 device
          support.  All CN6XXX based chips with USB are supported.

config USB_OCTEON2_COMMON
        bool
        default y if USB_OCTEON_EHCI || USB_OCTEON_OHCI

config USB_PXA168_EHCI
        bool "Marvell PXA168 on-chip EHCI HCD support"
        depends on USB_EHCI_HCD && ARCH_MMP
        help
          Enable support for Marvell PXA168 SoC's on-chip EHCI
          host controller