1menu "Bus options (PCI, PCMCIA, EISA, GSC, ISA)" 2 3config GSC 4 bool "VSC/GSC/HSC bus support" 5 default y 6 help 7 The VSC, GSC and HSC busses were used from the earliest 700-series 8 workstations up to and including the C360/J2240 workstations. They 9 were also used in servers from the E-class to the K-class. They 10 are not found in B1000, C3000, J5000, A500, L1000, N4000 and upwards. 11 If in doubt, say "Y". 12 13config HPPB 14 bool "HP-PB bus support" 15 depends on GSC 16 help 17 The HP-PB bus was used in the Nova class and K-class servers. 18 If in doubt, say "Y" 19 20config IOMMU_CCIO 21 bool "U2/Uturn I/O MMU" 22 depends on GSC 23 help 24 Say Y here to enable DMA management routines for the first 25 generation of PA-RISC cache-coherent machines. Programs the 26 U2/Uturn chip in "Virtual Mode" and use the I/O MMU. 27 28config GSC_LASI 29 bool "Lasi I/O support" 30 depends on GSC 31 help 32 Say Y here to support the Lasi multifunction chip found in 33 many PA-RISC workstations & servers. It includes interfaces 34 for a parallel port, serial port, NCR 53c710 SCSI, Apricot 35 Ethernet, Harmony audio, PS/2 keyboard & mouse, ISDN, telephony 36 and floppy. Note that you must still enable all the individual 37 drivers for these chips. 38 39config GSC_WAX 40 bool "Wax I/O support" 41 depends on GSC 42 help 43 Say Y here to support the Wax multifunction chip found in some 44 older systems, including B/C/D/R class and 715/64, 715/80 and 45 715/100. Wax includes an EISA adapter, a serial port (not always 46 used), a HIL interface chip and is also known to be used as the 47 GSC bridge for an X.25 GSC card. 48 49config EISA 50 bool "EISA support" 51 depends on GSC 52 help 53 Say Y here if you have an EISA bus in your machine. This code 54 supports both the Mongoose & Wax EISA adapters. It is sadly 55 incomplete and lacks support for card-to-host DMA. 56 57source "drivers/eisa/Kconfig" 58 59config ISA 60 bool "ISA support" 61 depends on EISA 62 help 63 If you want to plug an ISA card into your EISA bus, say Y here. 64 Most people should say N. 65 66config PCI 67 bool "PCI support" 68 help 69 All recent HP machines have PCI slots, and you should say Y here 70 if you have a recent machine. If you are convinced you do not have 71 PCI slots in your machine (eg a 712), then you may say "N" here. 72 Beware that some GSC cards have a Dino onboard and PCI inside them, 73 so it may be safest to say "Y" anyway. 74 75source "drivers/pci/Kconfig" 76 77config GSC_DINO 78 bool "GSCtoPCI/Dino PCI support" 79 depends on PCI && GSC 80 help 81 Say Y here to support the Dino & Cujo GSC to PCI bridges found in 82 machines from the B132 to the C360, the J2240 and the A180. Some 83 GSC/HSC cards (eg gigabit & dual 100 Mbit Ethernet) have a Dino on 84 the card, and you also need to say Y here if you have such a card. 85 Note that Dino also supplies one of the serial ports on certain 86 machines. If in doubt, say Y. 87 88config PCI_LBA 89 bool "LBA/Elroy PCI support" 90 depends on PCI 91 help 92 Say Y here to support the Elroy PCI Lower Bus Adapter. This is 93 present on B, C, J, L and N-class machines with 4-digit model 94 numbers and the A400/A500. 95 96config IOSAPIC 97 bool 98 depends on PCI_LBA 99 default PCI_LBA 100 101config IOMMU_SBA 102 bool 103 depends on PCI_LBA 104 default PCI_LBA 105 106config IOMMU_HELPER 107 bool 108 depends on IOMMU_SBA || IOMMU_CCIO 109 default y 110 111#config PCI_EPIC 112# bool "EPIC/SAGA PCI support" 113# depends on PCI 114# default y 115# help 116# Say Y here for V-class PCI, DMA/IOMMU, IRQ subsystem support. 117 118source "drivers/pcmcia/Kconfig" 119 120source "drivers/pci/hotplug/Kconfig" 121 122endmenu 123 124menu "PA-RISC specific drivers" 125 126config SUPERIO 127 bool "SuperIO (SuckyIO) support" 128 depends on PCI_LBA 129 default y 130 help 131 Say Y here to support the SuperIO chip found in Bxxxx, C3xxx and 132 J5xxx+ machines. This enables IDE, Floppy, Parallel Port, and 133 Serial port on those machines. 134 135config CHASSIS_LCD_LED 136 bool "Chassis LCD and LED support" 137 default y 138 help 139 Say Y here if you want to enable support for the Heartbeat, 140 Disk/Network activities LEDs on some PA-RISC machines, 141 or support for the LCD that can be found on recent material. 142 143 This has nothing to do with LED State support for A and E class. 144 145 If unsure, say Y. 146 147config PDC_CHASSIS 148 bool "PDC chassis state codes support" 149 default y 150 help 151 Say Y here if you want to enable support for Chassis codes. 152 That includes support for LED State front panel as found on E 153 class, and support for the GSP Virtual Front Panel (LED State and 154 message logging) as found on high end servers such as A, L and 155 N-class. 156 This driver will also display progress messages on LCD display, 157 such as "INI", "RUN" and "FLT", and might thus clobber messages 158 shown by the LED/LCD driver. 159 This driver updates the state panel (LED and/or LCD) upon system 160 state change (eg: boot, shutdown or panic). 161 162 If unsure, say Y. 163 164 165config PDC_CHASSIS_WARN 166 bool "PDC chassis warnings support" 167 depends on PROC_FS 168 default y 169 help 170 Say Y here if you want to enable support for Chassis warnings. 171 This will add a proc entry '/proc/chassis' giving some information 172 about the overall health state of the system. 173 This includes NVRAM battery level, overtemp or failures such as 174 fans or power units. 175 176 If unsure, say Y. 177 178 179config PDC_STABLE 180 tristate "PDC Stable Storage support" 181 depends on SYSFS 182 default y 183 help 184 Say Y here if you want to enable support for accessing Stable Storage 185 variables (PDC non volatile variables such as Primary Boot Path, 186 Console Path, Autoboot, Autosearch, etc) through SysFS. 187 188 If unsure, say Y. 189 190 To compile this driver as a module, choose M here. 191 The module will be called pdc_stable. 192 193endmenu 194