LXR linux-bk/drivers/scsi/scsi

   1#ifndef _SCSI_LOGGING_H
   2#define _SCSI_LOGGING_H
   3
   4#include <linux/config.h>
   5
   6/*
   7 * This defines the scsi logging feature.  It is a means by which the user
   8 * can select how much information they get about various goings on, and it
   9 * can be really useful for fault tracing.  The logging word is divided into
  10 * 8 nibbles, each of which describes a loglevel.  The division of things is
  11 * somewhat arbitrary, and the division of the word could be changed if it
  12 * were really needed for any reason.  The numbers below are the only place
  13 * where these are specified.  For a first go-around, 3 bits is more than
  14 * enough, since this gives 8 levels of logging (really 7, since 0 is always
  15 * off).  Cutting to 2 bits might be wise at some point.
  16 */
  17
  18#define SCSI_LOG_ERROR_SHIFT              0
  19#define SCSI_LOG_TIMEOUT_SHIFT            3
  20#define SCSI_LOG_SCAN_SHIFT               6
  21#define SCSI_LOG_MLQUEUE_SHIFT            9
  22#define SCSI_LOG_MLCOMPLETE_SHIFT         12
  23#define SCSI_LOG_LLQUEUE_SHIFT            15
  24#define SCSI_LOG_LLCOMPLETE_SHIFT         18
  25#define SCSI_LOG_HLQUEUE_SHIFT            21
  26#define SCSI_LOG_HLCOMPLETE_SHIFT         24
  27#define SCSI_LOG_IOCTL_SHIFT              27
  28
  29#define SCSI_LOG_ERROR_BITS               3
  30#define SCSI_LOG_TIMEOUT_BITS             3
  31#define SCSI_LOG_SCAN_BITS                3
  32#define SCSI_LOG_MLQUEUE_BITS             3
  33#define SCSI_LOG_MLCOMPLETE_BITS          3
  34#define SCSI_LOG_LLQUEUE_BITS             3
  35#define SCSI_LOG_LLCOMPLETE_BITS          3
  36#define SCSI_LOG_HLQUEUE_BITS             3
  37#define SCSI_LOG_HLCOMPLETE_BITS          3
  38#define SCSI_LOG_IOCTL_BITS               3
  39
  40extern unsigned int scsi_logging_level;
  41
  42#ifdef CONFIG_SCSI_LOGGING
  43
  44#define SCSI_LOG_LEVEL(SHIFT, BITS)                             \
  45        ((scsi_logging_level >> (SHIFT)) & ((1 << (BITS)) - 1))
  46
  47#define SCSI_CHECK_LOGGING(SHIFT, BITS, LEVEL, CMD)             \
  48{                                                               \
  49        if (unlikely((SCSI_LOG_LEVEL(SHIFT, BITS)) > (LEVEL)))  \
  50                (CMD);                                          \
  51}
  52#else
  53#define SCSI_CHECK_LOGGING(SHIFT, BITS, LEVEL, CMD)
  54#endif /* CONFIG_SCSI_LOGGING */
  55
  56/*
  57 * These are the macros that are actually used throughout the code to
  58 * log events.  If logging isn't enabled, they are no-ops and will be
  59 * completely absent from the user's code.
  60 */
  61#define SCSI_LOG_ERROR_RECOVERY(LEVEL,CMD)  \
  62        SCSI_CHECK_LOGGING(SCSI_LOG_ERROR_SHIFT, SCSI_LOG_ERROR_BITS, LEVEL,CMD);
  63#define SCSI_LOG_TIMEOUT(LEVEL,CMD)  \
  64        SCSI_CHECK_LOGGING(SCSI_LOG_TIMEOUT_SHIFT, SCSI_LOG_TIMEOUT_BITS, LEVEL,CMD);
  65#define SCSI_LOG_SCAN_BUS(LEVEL,CMD)  \
  66        SCSI_CHECK_LOGGING(SCSI_LOG_SCAN_SHIFT, SCSI_LOG_SCAN_BITS, LEVEL,CMD);
  67#define SCSI_LOG_MLQUEUE(LEVEL,CMD)  \
  68        SCSI_CHECK_LOGGING(SCSI_LOG_MLQUEUE_SHIFT, SCSI_LOG_MLQUEUE_BITS, LEVEL,CMD);
  69#define SCSI_LOG_MLCOMPLETE(LEVEL,CMD)  \
  70        SCSI_CHECK_LOGGING(SCSI_LOG_MLCOMPLETE_SHIFT, SCSI_LOG_MLCOMPLETE_BITS, LEVEL,CMD);
  71#define SCSI_LOG_LLQUEUE(LEVEL,CMD)  \
  72        SCSI_CHECK_LOGGING(SCSI_LOG_LLQUEUE_SHIFT, SCSI_LOG_LLQUEUE_BITS, LEVEL,CMD);
  73#define SCSI_LOG_LLCOMPLETE(LEVEL,CMD)  \
  74        SCSI_CHECK_LOGGING(SCSI_LOG_LLCOMPLETE_SHIFT, SCSI_LOG_LLCOMPLETE_BITS, LEVEL,CMD);
  75#define SCSI_LOG_HLQUEUE(LEVEL,CMD)  \
  76        SCSI_CHECK_LOGGING(SCSI_LOG_HLQUEUE_SHIFT, SCSI_LOG_HLQUEUE_BITS, LEVEL,CMD);
  77#define SCSI_LOG_HLCOMPLETE(LEVEL,CMD)  \
  78        SCSI_CHECK_LOGGING(SCSI_LOG_HLCOMPLETE_SHIFT, SCSI_LOG_HLCOMPLETE_BITS, LEVEL,CMD);
  79#define SCSI_LOG_IOCTL(LEVEL,CMD)  \
  80        SCSI_CHECK_LOGGING(SCSI_LOG_IOCTL_SHIFT, SCSI_LOG_IOCTL_BITS, LEVEL,CMD);
  81
  82#endif /* _SCSI_LOGGING_H */
  83