linux/drivers/video/Kconfig
<<
>>
Prefs
   1#
   2# Video configuration
   3#
   4
   5menu "Graphics support"
   6        depends on HAS_IOMEM
   7
   8config HAVE_FB_ATMEL
   9        bool
  10
  11config SH_MIPI_DSI
  12        tristate
  13        depends on (SUPERH || ARCH_SHMOBILE) && HAVE_CLK
  14
  15config SH_LCD_MIPI_DSI
  16        bool
  17
  18source "drivers/char/agp/Kconfig"
  19
  20source "drivers/gpu/vga/Kconfig"
  21
  22source "drivers/gpu/drm/Kconfig"
  23
  24config VGASTATE
  25       tristate
  26       default n
  27
  28config VIDEO_OUTPUT_CONTROL
  29        tristate "Lowlevel video output switch controls"
  30        help
  31          This framework adds support for low-level control of the video 
  32          output switch.
  33
  34config DISPLAY_TIMING
  35       bool
  36
  37config VIDEOMODE
  38       bool
  39
  40config OF_DISPLAY_TIMING
  41        bool "Enable device tree display timing support"
  42        depends on OF
  43        select DISPLAY_TIMING
  44        help
  45          helper to parse display timings from the devicetree
  46
  47config OF_VIDEOMODE
  48        bool "Enable device tree videomode support"
  49        depends on OF
  50        select VIDEOMODE
  51        select OF_DISPLAY_TIMING
  52        help
  53          helper to get videomodes from the devicetree
  54
  55config HDMI
  56        bool
  57
  58menuconfig FB
  59        tristate "Support for frame buffer devices"
  60        ---help---
  61          The frame buffer device provides an abstraction for the graphics
  62          hardware. It represents the frame buffer of some video hardware and
  63          allows application software to access the graphics hardware through
  64          a well-defined interface, so the software doesn't need to know
  65          anything about the low-level (hardware register) stuff.
  66
  67          Frame buffer devices work identically across the different
  68          architectures supported by Linux and make the implementation of
  69          application programs easier and more portable; at this point, an X
  70          server exists which uses the frame buffer device exclusively.
  71          On several non-X86 architectures, the frame buffer device is the
  72          only way to use the graphics hardware.
  73
  74          The device is accessed through special device nodes, usually located
  75          in the /dev directory, i.e. /dev/fb*.
  76
  77          You need an utility program called fbset to make full use of frame
  78          buffer devices. Please read <file:Documentation/fb/framebuffer.txt>
  79          and the Framebuffer-HOWTO at
  80          <http://www.munted.org.uk/programming/Framebuffer-HOWTO-1.3.html> for more
  81          information.
  82
  83          Say Y here and to the driver for your graphics board below if you
  84          are compiling a kernel for a non-x86 architecture.
  85
  86          If you are compiling for the x86 architecture, you can say Y if you
  87          want to play with it, but it is not essential. Please note that
  88          running graphical applications that directly touch the hardware
  89          (e.g. an accelerated X server) and that are not frame buffer
  90          device-aware may cause unexpected results. If unsure, say N.
  91
  92config FIRMWARE_EDID
  93       bool "Enable firmware EDID"
  94       depends on FB
  95       default n
  96       ---help---
  97         This enables access to the EDID transferred from the firmware.
  98         On the i386, this is from the Video BIOS. Enable this if DDC/I2C
  99         transfers do not work for your driver and if you are using
 100         nvidiafb, i810fb or savagefb.
 101
 102         In general, choosing Y for this option is safe.  If you
 103         experience extremely long delays while booting before you get
 104         something on your display, try setting this to N.  Matrox cards in
 105         combination with certain motherboards and monitors are known to
 106         suffer from this problem.
 107
 108config FB_DDC
 109       tristate
 110       depends on FB
 111       select I2C_ALGOBIT
 112       select I2C
 113       default n
 114
 115config FB_BOOT_VESA_SUPPORT
 116        bool
 117        depends on FB
 118        default n
 119        ---help---
 120          If true, at least one selected framebuffer driver can take advantage
 121          of VESA video modes set at an early boot stage via the vga= parameter.
 122
 123config FB_CFB_FILLRECT
 124        tristate
 125        depends on FB
 126        default n
 127        ---help---
 128          Include the cfb_fillrect function for generic software rectangle
 129          filling. This is used by drivers that don't provide their own
 130          (accelerated) version.
 131
 132config FB_CFB_COPYAREA
 133        tristate
 134        depends on FB
 135        default n
 136        ---help---
 137          Include the cfb_copyarea function for generic software area copying.
 138          This is used by drivers that don't provide their own (accelerated)
 139          version.
 140
 141config FB_CFB_IMAGEBLIT
 142        tristate
 143        depends on FB
 144        default n
 145        ---help---
 146          Include the cfb_imageblit function for generic software image
 147          blitting. This is used by drivers that don't provide their own
 148          (accelerated) version.
 149
 150config FB_CFB_REV_PIXELS_IN_BYTE
 151        bool
 152        depends on FB
 153        default n
 154        ---help---
 155          Allow generic frame-buffer functions to work on displays with 1, 2
 156          and 4 bits per pixel depths which has opposite order of pixels in
 157          byte order to bytes in long order.
 158
 159config FB_SYS_FILLRECT
 160        tristate
 161        depends on FB
 162        default n
 163        ---help---
 164          Include the sys_fillrect function for generic software rectangle
 165          filling. This is used by drivers that don't provide their own
 166          (accelerated) version and the framebuffer is in system RAM.
 167
 168config FB_SYS_COPYAREA
 169        tristate
 170        depends on FB
 171        default n
 172        ---help---
 173          Include the sys_copyarea function for generic software area copying.
 174          This is used by drivers that don't provide their own (accelerated)
 175          version and the framebuffer is in system RAM.
 176
 177config FB_SYS_IMAGEBLIT
 178        tristate
 179        depends on FB
 180        default n
 181        ---help---
 182          Include the sys_imageblit function for generic software image
 183          blitting. This is used by drivers that don't provide their own
 184          (accelerated) version and the framebuffer is in system RAM.
 185
 186menuconfig FB_FOREIGN_ENDIAN
 187        bool "Framebuffer foreign endianness support"
 188        depends on FB
 189        ---help---
 190          This menu will let you enable support for the framebuffers with
 191          non-native endianness (e.g. Little-Endian framebuffer on a
 192          Big-Endian machine). Most probably you don't have such hardware,
 193          so it's safe to say "n" here.
 194
 195choice
 196        prompt "Choice endianness support"
 197        depends on FB_FOREIGN_ENDIAN
 198
 199config FB_BOTH_ENDIAN
 200        bool "Support for Big- and Little-Endian framebuffers"
 201
 202config FB_BIG_ENDIAN
 203        bool "Support for Big-Endian framebuffers only"
 204
 205config FB_LITTLE_ENDIAN
 206        bool "Support for Little-Endian framebuffers only"
 207
 208endchoice
 209
 210config FB_SYS_FOPS
 211       tristate
 212       depends on FB
 213       default n
 214
 215config FB_WMT_GE_ROPS
 216        tristate
 217        depends on FB
 218        default n
 219        ---help---
 220          Include functions for accelerated rectangle filling and area
 221          copying using WonderMedia Graphics Engine operations.
 222
 223config FB_DEFERRED_IO
 224        bool
 225        depends on FB
 226
 227config FB_HECUBA
 228        tristate
 229        depends on FB
 230        depends on FB_DEFERRED_IO
 231
 232config FB_SVGALIB
 233        tristate
 234        depends on FB
 235        default n
 236        ---help---
 237          Common utility functions useful to fbdev drivers of VGA-based
 238          cards.
 239
 240config FB_MACMODES
 241       tristate
 242       depends on FB
 243       default n
 244
 245config FB_BACKLIGHT
 246        bool
 247        depends on FB
 248        select BACKLIGHT_LCD_SUPPORT
 249        select BACKLIGHT_CLASS_DEVICE
 250        default n
 251
 252config FB_MODE_HELPERS
 253        bool "Enable Video Mode Handling Helpers"
 254        depends on FB
 255        default n
 256        ---help---
 257          This enables functions for handling video modes using the
 258          Generalized Timing Formula and the EDID parser. A few drivers rely
 259          on this feature such as the radeonfb, rivafb, and the i810fb. If
 260          your driver does not take advantage of this feature, choosing Y will
 261          just increase the kernel size by about 5K.
 262
 263config FB_TILEBLITTING
 264       bool "Enable Tile Blitting Support"
 265       depends on FB
 266       default n
 267       ---help---
 268         This enables tile blitting.  Tile blitting is a drawing technique
 269         where the screen is divided into rectangular sections (tiles), whereas
 270         the standard blitting divides the screen into pixels. Because the
 271         default drawing element is a tile, drawing functions will be passed
 272         parameters in terms of number of tiles instead of number of pixels.
 273         For example, to draw a single character, instead of using bitmaps,
 274         an index to an array of bitmaps will be used.  To clear or move a
 275         rectangular section of a screen, the rectangle will be described in
 276         terms of number of tiles in the x- and y-axis.
 277
 278         This is particularly important to one driver, matroxfb.  If
 279         unsure, say N.
 280
 281comment "Frame buffer hardware drivers"
 282        depends on FB
 283
 284config FB_GRVGA
 285        tristate "Aeroflex Gaisler framebuffer support"
 286        depends on FB && SPARC
 287        select FB_CFB_FILLRECT
 288        select FB_CFB_COPYAREA
 289        select FB_CFB_IMAGEBLIT
 290        ---help---
 291        This enables support for the SVGACTRL framebuffer in the GRLIB IP library from Aeroflex Gaisler.
 292
 293config FB_CIRRUS
 294        tristate "Cirrus Logic support"
 295        depends on FB && (ZORRO || PCI)
 296        select FB_CFB_FILLRECT
 297        select FB_CFB_COPYAREA
 298        select FB_CFB_IMAGEBLIT
 299        ---help---
 300          This enables support for Cirrus Logic GD542x/543x based boards on
 301          Amiga: SD64, Piccolo, Picasso II/II+, Picasso IV, or EGS Spectrum.
 302
 303          If you have a PCI-based system, this enables support for these
 304          chips: GD-543x, GD-544x, GD-5480.
 305
 306          Please read the file <file:Documentation/fb/cirrusfb.txt>.
 307
 308          Say N unless you have such a graphics board or plan to get one
 309          before you next recompile the kernel.
 310
 311config FB_PM2
 312        tristate "Permedia2 support"
 313        depends on FB && ((AMIGA && BROKEN) || PCI)
 314        select FB_CFB_FILLRECT
 315        select FB_CFB_COPYAREA
 316        select FB_CFB_IMAGEBLIT
 317        help
 318          This is the frame buffer device driver for cards based on
 319          the 3D Labs Permedia, Permedia 2 and Permedia 2V chips.
 320          The driver was tested on the following cards:
 321                Diamond FireGL 1000 PRO AGP
 322                ELSA Gloria Synergy PCI
 323                Appian Jeronimo PRO (both heads) PCI
 324                3DLabs Oxygen ACX aka EONtronics Picasso P2 PCI
 325                Techsource Raptor GFX-8P (aka Sun PGX-32) on SPARC
 326                ASK Graphic Blaster Exxtreme AGP
 327
 328          To compile this driver as a module, choose M here: the
 329          module will be called pm2fb.
 330
 331config FB_PM2_FIFO_DISCONNECT
 332        bool "enable FIFO disconnect feature"
 333        depends on FB_PM2 && PCI
 334        help
 335          Support the Permedia2 FIFO disconnect feature.
 336
 337config FB_ARMCLCD
 338        tristate "ARM PrimeCell PL110 support"
 339        depends on FB && ARM && ARM_AMBA
 340        select FB_CFB_FILLRECT
 341        select FB_CFB_COPYAREA
 342        select FB_CFB_IMAGEBLIT
 343        help
 344          This framebuffer device driver is for the ARM PrimeCell PL110
 345          Colour LCD controller.  ARM PrimeCells provide the building
 346          blocks for System on a Chip devices.
 347
 348          If you want to compile this as a module (=code which can be
 349          inserted into and removed from the running kernel), say M
 350          here and read <file:Documentation/kbuild/modules.txt>.  The module
 351          will be called amba-clcd.
 352
 353config FB_ACORN
 354        bool "Acorn VIDC support"
 355        depends on (FB = y) && ARM && ARCH_ACORN
 356        select FB_CFB_FILLRECT
 357        select FB_CFB_COPYAREA
 358        select FB_CFB_IMAGEBLIT
 359        help
 360          This is the frame buffer device driver for the Acorn VIDC graphics
 361          hardware found in Acorn RISC PCs and other ARM-based machines.  If
 362          unsure, say N.
 363
 364config FB_CLPS711X
 365        bool "CLPS711X LCD support"
 366        depends on (FB = y) && ARM && ARCH_CLPS711X
 367        select FB_CFB_FILLRECT
 368        select FB_CFB_COPYAREA
 369        select FB_CFB_IMAGEBLIT
 370        help
 371          Say Y to enable the Framebuffer driver for the CLPS7111 and
 372          EP7212 processors.
 373
 374config FB_SA1100
 375        bool "SA-1100 LCD support"
 376        depends on (FB = y) && ARM && ARCH_SA1100
 377        select FB_CFB_FILLRECT
 378        select FB_CFB_COPYAREA
 379        select FB_CFB_IMAGEBLIT
 380        help
 381          This is a framebuffer device for the SA-1100 LCD Controller.
 382          See <http://www.linux-fbdev.org/> for information on framebuffer
 383          devices.
 384
 385          If you plan to use the LCD display with your SA-1100 system, say
 386          Y here.
 387
 388config FB_IMX
 389        tristate "Freescale i.MX1/21/25/27 LCD support"
 390        depends on FB && IMX_HAVE_PLATFORM_IMX_FB
 391        select FB_CFB_FILLRECT
 392        select FB_CFB_COPYAREA
 393        select FB_CFB_IMAGEBLIT
 394
 395config FB_CYBER2000
 396        tristate "CyberPro 2000/2010/5000 support"
 397        depends on FB && PCI && (BROKEN || !SPARC64)
 398        select FB_CFB_FILLRECT
 399        select FB_CFB_COPYAREA
 400        select FB_CFB_IMAGEBLIT
 401        help
 402          This enables support for the Integraphics CyberPro 20x0 and 5000
 403          VGA chips used in the Rebel.com Netwinder and other machines.
 404          Say Y if you have a NetWinder or a graphics card containing this
 405          device, otherwise say N.
 406
 407config FB_CYBER2000_DDC
 408        bool "DDC for CyberPro support"
 409        depends on FB_CYBER2000
 410        select FB_DDC
 411        default y
 412        help
 413          Say Y here if you want DDC support for your CyberPro graphics
 414          card. This is only I2C bus support, driver does not use EDID.
 415
 416config FB_CYBER2000_I2C
 417        bool "CyberPro 2000/2010/5000 I2C support"
 418        depends on FB_CYBER2000 && I2C && ARCH_NETWINDER
 419        select I2C_ALGOBIT
 420        help
 421          Enable support for the I2C video decoder interface on the
 422          Integraphics CyberPro 20x0 and 5000 VGA chips.  This is used
 423          on the Netwinder machines for the SAA7111 video capture.
 424
 425config FB_APOLLO
 426        bool
 427        depends on (FB = y) && APOLLO
 428        default y
 429        select FB_CFB_FILLRECT
 430        select FB_CFB_IMAGEBLIT
 431
 432config FB_Q40
 433        bool
 434        depends on (FB = y) && Q40
 435        default y
 436        select FB_CFB_FILLRECT
 437        select FB_CFB_COPYAREA
 438        select FB_CFB_IMAGEBLIT
 439
 440config FB_AMIGA
 441        tristate "Amiga native chipset support"
 442        depends on FB && AMIGA
 443        help
 444          This is the frame buffer device driver for the builtin graphics
 445          chipset found in Amigas.
 446
 447          To compile this driver as a module, choose M here: the
 448          module will be called amifb.
 449
 450config FB_AMIGA_OCS
 451        bool "Amiga OCS chipset support"
 452        depends on FB_AMIGA
 453        help
 454          This enables support for the original Agnus and Denise video chips,
 455          found in the Amiga 1000 and most A500's and A2000's. If you intend
 456          to run Linux on any of these systems, say Y; otherwise say N.
 457
 458config FB_AMIGA_ECS
 459        bool "Amiga ECS chipset support"
 460        depends on FB_AMIGA
 461        help
 462          This enables support for the Enhanced Chip Set, found in later
 463          A500's, later A2000's, the A600, the A3000, the A3000T and CDTV. If
 464          you intend to run Linux on any of these systems, say Y; otherwise
 465          say N.
 466
 467config FB_AMIGA_AGA
 468        bool "Amiga AGA chipset support"
 469        depends on FB_AMIGA
 470        help
 471          This enables support for the Advanced Graphics Architecture (also
 472          known as the AGA or AA) Chip Set, found in the A1200, A4000, A4000T
 473          and CD32. If you intend to run Linux on any of these systems, say Y;
 474          otherwise say N.
 475
 476config FB_FM2
 477        bool "Amiga FrameMaster II/Rainbow II support"
 478        depends on (FB = y) && ZORRO
 479        select FB_CFB_FILLRECT
 480        select FB_CFB_COPYAREA
 481        select FB_CFB_IMAGEBLIT
 482        help
 483          This is the frame buffer device driver for the Amiga FrameMaster
 484          card from BSC (exhibited 1992 but not shipped as a CBM product).
 485
 486config FB_ARC
 487        tristate "Arc Monochrome LCD board support"
 488        depends on FB && X86
 489        select FB_SYS_FILLRECT
 490        select FB_SYS_COPYAREA
 491        select FB_SYS_IMAGEBLIT
 492        select FB_SYS_FOPS
 493        help
 494          This enables support for the Arc Monochrome LCD board. The board
 495          is based on the KS-108 lcd controller and is typically a matrix
 496          of 2*n chips. This driver was tested with a 128x64 panel. This
 497          driver supports it for use with x86 SBCs through a 16 bit GPIO
 498          interface (8 bit data, 8 bit control). If you anticipate using
 499          this driver, say Y or M; otherwise say N. You must specify the
 500          GPIO IO address to be used for setting control and data.
 501
 502config FB_ATARI
 503        bool "Atari native chipset support"
 504        depends on (FB = y) && ATARI
 505        select FB_CFB_FILLRECT
 506        select FB_CFB_COPYAREA
 507        select FB_CFB_IMAGEBLIT
 508        help
 509          This is the frame buffer device driver for the builtin graphics
 510          chipset found in Ataris.
 511
 512config FB_OF
 513        bool "Open Firmware frame buffer device support"
 514        depends on (FB = y) && (PPC64 || PPC_OF) && (!PPC_PSERIES || PCI)
 515        select FB_CFB_FILLRECT
 516        select FB_CFB_COPYAREA
 517        select FB_CFB_IMAGEBLIT
 518        select FB_MACMODES
 519        help
 520          Say Y if you want support with Open Firmware for your graphics
 521          board.
 522
 523config FB_CONTROL
 524        bool "Apple \"control\" display support"
 525        depends on (FB = y) && PPC_PMAC && PPC32
 526        select FB_CFB_FILLRECT
 527        select FB_CFB_COPYAREA
 528        select FB_CFB_IMAGEBLIT
 529        select FB_MACMODES
 530        help
 531          This driver supports a frame buffer for the graphics adapter in the
 532          Power Macintosh 7300 and others.
 533
 534config FB_PLATINUM
 535        bool "Apple \"platinum\" display support"
 536        depends on (FB = y) && PPC_PMAC && PPC32
 537        select FB_CFB_FILLRECT
 538        select FB_CFB_COPYAREA
 539        select FB_CFB_IMAGEBLIT
 540        select FB_MACMODES
 541        help
 542          This driver supports a frame buffer for the "platinum" graphics
 543          adapter in some Power Macintoshes.
 544
 545config FB_VALKYRIE
 546        bool "Apple \"valkyrie\" display support"
 547        depends on (FB = y) && (MAC || (PPC_PMAC && PPC32))
 548        select FB_CFB_FILLRECT
 549        select FB_CFB_COPYAREA
 550        select FB_CFB_IMAGEBLIT
 551        select FB_MACMODES
 552        help
 553          This driver supports a frame buffer for the "valkyrie" graphics
 554          adapter in some Power Macintoshes.
 555
 556config FB_CT65550
 557        bool "Chips 65550 display support"
 558        depends on (FB = y) && PPC32 && PCI
 559        select FB_CFB_FILLRECT
 560        select FB_CFB_COPYAREA
 561        select FB_CFB_IMAGEBLIT
 562        help
 563          This is the frame buffer device driver for the Chips & Technologies
 564          65550 graphics chip in PowerBooks.
 565
 566config FB_ASILIANT
 567        bool "Asiliant (Chips) 69000 display support"
 568        depends on (FB = y) && PCI
 569        select FB_CFB_FILLRECT
 570        select FB_CFB_COPYAREA
 571        select FB_CFB_IMAGEBLIT
 572        help
 573          This is the frame buffer device driver for the Asiliant 69030 chipset
 574
 575config FB_IMSTT
 576        bool "IMS Twin Turbo display support"
 577        depends on (FB = y) && PCI
 578        select FB_CFB_IMAGEBLIT
 579        select FB_MACMODES if PPC
 580        help
 581          The IMS Twin Turbo is a PCI-based frame buffer card bundled with
 582          many Macintosh and compatible computers.
 583
 584config FB_VGA16
 585        tristate "VGA 16-color graphics support"
 586        depends on FB && (X86 || PPC)
 587        select FB_CFB_FILLRECT
 588        select FB_CFB_COPYAREA
 589        select FB_CFB_IMAGEBLIT
 590        select VGASTATE
 591        select FONT_8x16 if FRAMEBUFFER_CONSOLE
 592        help
 593          This is the frame buffer device driver for VGA 16 color graphic
 594          cards. Say Y if you have such a card.
 595
 596          To compile this driver as a module, choose M here: the
 597          module will be called vga16fb.
 598
 599config FB_BF54X_LQ043
 600        tristate "SHARP LQ043 TFT LCD (BF548 EZKIT)"
 601        depends on FB && (BF54x) && !BF542
 602        select FB_CFB_FILLRECT
 603        select FB_CFB_COPYAREA
 604        select FB_CFB_IMAGEBLIT
 605        help
 606         This is the framebuffer device driver for a SHARP LQ043T1DG01 TFT LCD
 607
 608config FB_BFIN_T350MCQB
 609        tristate "Varitronix COG-T350MCQB TFT LCD display (BF527 EZKIT)"
 610        depends on FB && BLACKFIN
 611        select BFIN_GPTIMERS
 612        select FB_CFB_FILLRECT
 613        select FB_CFB_COPYAREA
 614        select FB_CFB_IMAGEBLIT
 615        help
 616         This is the framebuffer device driver for a Varitronix VL-PS-COG-T350MCQB-01 display TFT LCD
 617         This display is a QVGA 320x240 24-bit RGB display interfaced by an 8-bit wide PPI
 618         It uses PPI[0..7] PPI_FS1, PPI_FS2 and PPI_CLK.
 619
 620config FB_BFIN_LQ035Q1
 621        tristate "SHARP LQ035Q1DH02 TFT LCD"
 622        depends on FB && BLACKFIN && SPI
 623        select FB_CFB_FILLRECT
 624        select FB_CFB_COPYAREA
 625        select FB_CFB_IMAGEBLIT
 626        select BFIN_GPTIMERS
 627        help
 628          This is the framebuffer device driver for a SHARP LQ035Q1DH02 TFT display found on
 629          the Blackfin Landscape LCD EZ-Extender Card.
 630          This display is a QVGA 320x240 18-bit RGB display interfaced by an 16-bit wide PPI
 631          It uses PPI[0..15] PPI_FS1, PPI_FS2 and PPI_CLK.
 632
 633          To compile this driver as a module, choose M here: the
 634          module will be called bfin-lq035q1-fb.
 635
 636config FB_BF537_LQ035
 637        tristate "SHARP LQ035 TFT LCD (BF537 STAMP)"
 638        depends on FB && (BF534 || BF536 || BF537) && I2C_BLACKFIN_TWI
 639        select FB_CFB_FILLRECT
 640        select FB_CFB_COPYAREA
 641        select FB_CFB_IMAGEBLIT
 642        select BFIN_GPTIMERS
 643        help
 644          This is the framebuffer device for a SHARP LQ035Q7DB03 TFT LCD
 645          attached to a BF537.
 646
 647          To compile this driver as a module, choose M here: the
 648          module will be called bf537-lq035.
 649
 650config FB_BFIN_7393
 651        tristate "Blackfin ADV7393 Video encoder"
 652        depends on FB && BLACKFIN
 653        select I2C
 654        select FB_CFB_FILLRECT
 655        select FB_CFB_COPYAREA
 656        select FB_CFB_IMAGEBLIT
 657        help
 658          This is the framebuffer device for a ADV7393 video encoder
 659          attached to a Blackfin on the PPI port.
 660          If your Blackfin board has a ADV7393 select Y.
 661
 662          To compile this driver as a module, choose M here: the
 663          module will be called bfin_adv7393fb.
 664
 665choice
 666        prompt  "Video mode support"
 667        depends on FB_BFIN_7393
 668        default NTSC
 669
 670config NTSC
 671        bool 'NTSC 720x480'
 672
 673config PAL
 674        bool 'PAL 720x576'
 675
 676config NTSC_640x480
 677        bool 'NTSC 640x480 (Experimental)'
 678
 679config PAL_640x480
 680        bool 'PAL 640x480 (Experimental)'
 681
 682config NTSC_YCBCR
 683        bool 'NTSC 720x480 YCbCR input'
 684
 685config PAL_YCBCR
 686        bool 'PAL 720x576 YCbCR input'
 687
 688endchoice
 689
 690choice
 691        prompt  "Size of ADV7393 frame buffer memory Single/Double Size"
 692        depends on (FB_BFIN_7393)
 693        default ADV7393_1XMEM
 694
 695config ADV7393_1XMEM
 696        bool 'Single'
 697
 698config ADV7393_2XMEM
 699        bool 'Double'
 700endchoice
 701
 702config FB_STI
 703        tristate "HP STI frame buffer device support"
 704        depends on FB && PARISC
 705        select FB_CFB_FILLRECT
 706        select FB_CFB_COPYAREA
 707        select FB_CFB_IMAGEBLIT
 708        select STI_CONSOLE
 709        select VT
 710        default y
 711        ---help---
 712          STI refers to the HP "Standard Text Interface" which is a set of
 713          BIOS routines contained in a ROM chip in HP PA-RISC based machines.
 714          Enabling this option will implement the linux framebuffer device
 715          using calls to the STI BIOS routines for initialisation.
 716        
 717          If you enable this option, you will get a planar framebuffer device
 718          /dev/fb which will work on the most common HP graphic cards of the
 719          NGLE family, including the artist chips (in the 7xx and Bxxx series),
 720          HCRX, HCRX24, CRX, CRX24 and VisEG series.
 721
 722          It is safe to enable this option, so you should probably say "Y".
 723
 724config FB_MAC
 725        bool "Generic Macintosh display support"
 726        depends on (FB = y) && MAC
 727        select FB_CFB_FILLRECT
 728        select FB_CFB_COPYAREA
 729        select FB_CFB_IMAGEBLIT
 730        select FB_MACMODES
 731
 732config FB_HP300
 733        bool
 734        depends on (FB = y) && DIO
 735        select FB_CFB_IMAGEBLIT
 736        default y
 737
 738config FB_TGA
 739        tristate "TGA/SFB+ framebuffer support"
 740        depends on FB && (ALPHA || TC)
 741        select FB_CFB_FILLRECT
 742        select FB_CFB_COPYAREA
 743        select FB_CFB_IMAGEBLIT
 744        select BITREVERSE
 745        ---help---
 746          This is the frame buffer device driver for generic TGA and SFB+
 747          graphic cards.  These include DEC ZLXp-E1, -E2 and -E3 PCI cards,
 748          also known as PBXGA-A, -B and -C, and DEC ZLX-E1, -E2 and -E3
 749          TURBOchannel cards, also known as PMAGD-A, -B and -C.
 750
 751          Due to hardware limitations ZLX-E2 and E3 cards are not supported
 752          for DECstation 5000/200 systems.  Additionally due to firmware
 753          limitations these cards may cause troubles with booting DECstation
 754          5000/240 and /260 systems, but are fully supported under Linux if
 755          you manage to get it going. ;-)
 756
 757          Say Y if you have one of those.
 758
 759config FB_UVESA
 760        tristate "Userspace VESA VGA graphics support"
 761        depends on FB && CONNECTOR
 762        select FB_CFB_FILLRECT
 763        select FB_CFB_COPYAREA
 764        select FB_CFB_IMAGEBLIT
 765        select FB_MODE_HELPERS
 766        help
 767          This is the frame buffer driver for generic VBE 2.0 compliant
 768          graphic cards. It can also take advantage of VBE 3.0 features,
 769          such as refresh rate adjustment.
 770
 771          This driver generally provides more features than vesafb but
 772          requires a userspace helper application called 'v86d'. See
 773          <file:Documentation/fb/uvesafb.txt> for more information.
 774
 775          If unsure, say N.
 776
 777config FB_VESA
 778        bool "VESA VGA graphics support"
 779        depends on (FB = y) && X86
 780        select FB_CFB_FILLRECT
 781        select FB_CFB_COPYAREA
 782        select FB_CFB_IMAGEBLIT
 783        select FB_BOOT_VESA_SUPPORT
 784        help
 785          This is the frame buffer device driver for generic VESA 2.0
 786          compliant graphic cards. The older VESA 1.2 cards are not supported.
 787          You will get a boot time penguin logo at no additional cost. Please
 788          read <file:Documentation/fb/vesafb.txt>. If unsure, say Y.
 789
 790config FB_EFI
 791        bool "EFI-based Framebuffer Support"
 792        depends on (FB = y) && X86 && EFI
 793        select FB_CFB_FILLRECT
 794        select FB_CFB_COPYAREA
 795        select FB_CFB_IMAGEBLIT
 796        help
 797          This is the EFI frame buffer device driver. If the firmware on
 798          your platform is EFI 1.10 or UEFI 2.0, select Y to add support for
 799          using the EFI framebuffer as your console.
 800
 801config FB_N411
 802       tristate "N411 Apollo/Hecuba devkit support"
 803       depends on FB && X86 && MMU
 804       select FB_SYS_FILLRECT
 805       select FB_SYS_COPYAREA
 806       select FB_SYS_IMAGEBLIT
 807       select FB_SYS_FOPS
 808       select FB_DEFERRED_IO
 809       select FB_HECUBA
 810       help
 811         This enables support for the Apollo display controller in its
 812         Hecuba form using the n411 devkit.
 813
 814config FB_HGA
 815        tristate "Hercules mono graphics support"
 816        depends on FB && X86
 817        help
 818          Say Y here if you have a Hercules mono graphics card.
 819
 820          To compile this driver as a module, choose M here: the
 821          module will be called hgafb.
 822
 823          As this card technology is at least 25 years old,
 824          most people will answer N here.
 825
 826config FB_SGIVW
 827        tristate "SGI Visual Workstation framebuffer support"
 828        depends on FB && X86_VISWS
 829        select FB_CFB_FILLRECT
 830        select FB_CFB_COPYAREA
 831        select FB_CFB_IMAGEBLIT
 832        help
 833          SGI Visual Workstation support for framebuffer graphics.
 834
 835config FB_GBE
 836        bool "SGI Graphics Backend frame buffer support"
 837        depends on (FB = y) && (SGI_IP32 || X86_VISWS)
 838        select FB_CFB_FILLRECT
 839        select FB_CFB_COPYAREA
 840        select FB_CFB_IMAGEBLIT
 841        help
 842          This is the frame buffer device driver for SGI Graphics Backend.
 843          This chip is used in SGI O2 and Visual Workstation 320/540.
 844
 845config FB_GBE_MEM
 846        int "Video memory size in MB"
 847        depends on FB_GBE
 848        default 4
 849        help
 850          This is the amount of memory reserved for the framebuffer,
 851          which can be any value between 1MB and 8MB.
 852
 853config FB_SBUS
 854        bool "SBUS and UPA framebuffers"
 855        depends on (FB = y) && SPARC
 856        help
 857          Say Y if you want support for SBUS or UPA based frame buffer device.
 858
 859config FB_BW2
 860        bool "BWtwo support"
 861        depends on (FB = y) && (SPARC && FB_SBUS)
 862        select FB_CFB_FILLRECT
 863        select FB_CFB_COPYAREA
 864        select FB_CFB_IMAGEBLIT
 865        help
 866          This is the frame buffer device driver for the BWtwo frame buffer.
 867
 868config FB_CG3
 869        bool "CGthree support"
 870        depends on (FB = y) && (SPARC && FB_SBUS)
 871        select FB_CFB_FILLRECT
 872        select FB_CFB_COPYAREA
 873        select FB_CFB_IMAGEBLIT
 874        help
 875          This is the frame buffer device driver for the CGthree frame buffer.
 876
 877config FB_CG6
 878        bool "CGsix (GX,TurboGX) support"
 879        depends on (FB = y) && (SPARC && FB_SBUS)
 880        select FB_CFB_COPYAREA
 881        select FB_CFB_IMAGEBLIT
 882        help
 883          This is the frame buffer device driver for the CGsix (GX, TurboGX)
 884          frame buffer.
 885
 886config FB_FFB
 887        bool "Creator/Creator3D/Elite3D support"
 888        depends on FB_SBUS && SPARC64
 889        select FB_CFB_COPYAREA
 890        select FB_CFB_IMAGEBLIT
 891        help
 892          This is the frame buffer device driver for the Creator, Creator3D,
 893          and Elite3D graphics boards.
 894
 895config FB_TCX
 896        bool "TCX (SS4/SS5 only) support"
 897        depends on FB_SBUS
 898        select FB_CFB_FILLRECT
 899        select FB_CFB_COPYAREA
 900        select FB_CFB_IMAGEBLIT
 901        help
 902          This is the frame buffer device driver for the TCX 24/8bit frame
 903          buffer.
 904
 905config FB_CG14
 906        bool "CGfourteen (SX) support"
 907        depends on FB_SBUS
 908        select FB_CFB_FILLRECT
 909        select FB_CFB_COPYAREA
 910        select FB_CFB_IMAGEBLIT
 911        help
 912          This is the frame buffer device driver for the CGfourteen frame
 913          buffer on Desktop SPARCsystems with the SX graphics option.
 914
 915config FB_P9100
 916        bool "P9100 (Sparcbook 3 only) support"
 917        depends on FB_SBUS
 918        select FB_CFB_FILLRECT
 919        select FB_CFB_COPYAREA
 920        select FB_CFB_IMAGEBLIT
 921        help
 922          This is the frame buffer device driver for the P9100 card
 923          supported on Sparcbook 3 machines.
 924
 925config FB_LEO
 926        bool "Leo (ZX) support"
 927        depends on FB_SBUS
 928        select FB_CFB_FILLRECT
 929        select FB_CFB_COPYAREA
 930        select FB_CFB_IMAGEBLIT
 931        help
 932          This is the frame buffer device driver for the SBUS-based Sun ZX
 933          (leo) frame buffer cards.
 934
 935config FB_IGA
 936        bool "IGA 168x display support"
 937        depends on (FB = y) && SPARC32
 938        select FB_CFB_FILLRECT
 939        select FB_CFB_COPYAREA
 940        select FB_CFB_IMAGEBLIT
 941        help
 942          This is the framebuffer device for the INTERGRAPHICS 1680 and
 943          successor frame buffer cards.
 944
 945config FB_XVR500
 946        bool "Sun XVR-500 3DLABS Wildcat support"
 947        depends on (FB = y) && PCI && SPARC64
 948        select FB_CFB_FILLRECT
 949        select FB_CFB_COPYAREA
 950        select FB_CFB_IMAGEBLIT
 951        help
 952          This is the framebuffer device for the Sun XVR-500 and similar
 953          graphics cards based upon the 3DLABS Wildcat chipset.  The driver
 954          only works on sparc64 systems where the system firmware has
 955          mostly initialized the card already.  It is treated as a
 956          completely dumb framebuffer device.
 957
 958config FB_XVR2500
 959        bool "Sun XVR-2500 3DLABS Wildcat support"
 960        depends on (FB = y) && PCI && SPARC64
 961        select FB_CFB_FILLRECT
 962        select FB_CFB_COPYAREA
 963        select FB_CFB_IMAGEBLIT
 964        help
 965          This is the framebuffer device for the Sun XVR-2500 and similar
 966          graphics cards based upon the 3DLABS Wildcat chipset.  The driver
 967          only works on sparc64 systems where the system firmware has
 968          mostly initialized the card already.  It is treated as a
 969          completely dumb framebuffer device.
 970
 971config FB_XVR1000
 972        bool "Sun XVR-1000 support"
 973        depends on (FB = y) && SPARC64
 974        select FB_CFB_FILLRECT
 975        select FB_CFB_COPYAREA
 976        select FB_CFB_IMAGEBLIT
 977        help
 978          This is the framebuffer device for the Sun XVR-1000 and similar
 979          graphics cards.  The driver only works on sparc64 systems where
 980          the system firmware has mostly initialized the card already.  It
 981          is treated as a completely dumb framebuffer device.
 982
 983config FB_PVR2
 984        tristate "NEC PowerVR 2 display support"
 985        depends on FB && SH_DREAMCAST
 986        select FB_CFB_FILLRECT
 987        select FB_CFB_COPYAREA
 988        select FB_CFB_IMAGEBLIT
 989        ---help---
 990          Say Y here if you have a PowerVR 2 card in your box.  If you plan to
 991          run linux on your Dreamcast, you will have to say Y here.
 992          This driver may or may not work on other PowerVR 2 cards, but is
 993          totally untested.  Use at your own risk.  If unsure, say N.
 994
 995          To compile this driver as a module, choose M here: the
 996          module will be called pvr2fb.
 997
 998          You can pass several parameters to the driver at boot time or at
 999          module load time.  The parameters look like "video=pvr2:XXX", where
1000          the meaning of XXX can be found at the end of the main source file
1001          (<file:drivers/video/pvr2fb.c>). Please see the file
1002          <file:Documentation/fb/pvr2fb.txt>.
1003
1004config FB_S1D13XXX
1005        tristate "Epson S1D13XXX framebuffer support"
1006        depends on FB
1007        select FB_CFB_FILLRECT
1008        select FB_CFB_COPYAREA
1009        select FB_CFB_IMAGEBLIT
1010        help
1011          Support for S1D13XXX framebuffer device family (currently only
1012          working with S1D13806). Product specs at
1013          <http://vdc.epson.com/>
1014
1015config FB_ATMEL
1016        tristate "AT91/AT32 LCD Controller support"
1017        depends on FB && HAVE_FB_ATMEL
1018        select FB_CFB_FILLRECT
1019        select FB_CFB_COPYAREA
1020        select FB_CFB_IMAGEBLIT
1021        help
1022          This enables support for the AT91/AT32 LCD Controller.
1023
1024config FB_INTSRAM
1025        bool "Frame Buffer in internal SRAM"
1026        depends on FB_ATMEL && ARCH_AT91SAM9261
1027        help
1028          Say Y if you want to map Frame Buffer in internal SRAM. Say N if you want
1029          to let frame buffer in external SDRAM.
1030
1031config FB_ATMEL_STN
1032        bool "Use a STN display with AT91/AT32 LCD Controller"
1033        depends on FB_ATMEL && (MACH_AT91SAM9261EK || MACH_AT91SAM9G10EK)
1034        default n
1035        help
1036          Say Y if you want to connect a STN LCD display to the AT91/AT32 LCD
1037          Controller. Say N if you want to connect a TFT.
1038
1039          If unsure, say N.
1040
1041config FB_NVIDIA
1042        tristate "nVidia Framebuffer Support"
1043        depends on FB && PCI
1044        select FB_BACKLIGHT if FB_NVIDIA_BACKLIGHT
1045        select FB_MODE_HELPERS
1046        select FB_CFB_FILLRECT
1047        select FB_CFB_COPYAREA
1048        select FB_CFB_IMAGEBLIT
1049        select BITREVERSE
1050        select VGASTATE
1051        help
1052          This driver supports graphics boards with the nVidia chips, TNT
1053          and newer. For very old chipsets, such as the RIVA128, then use
1054          the rivafb.
1055          Say Y if you have such a graphics board.
1056
1057          To compile this driver as a module, choose M here: the
1058          module will be called nvidiafb.
1059
1060config FB_NVIDIA_I2C
1061       bool "Enable DDC Support"
1062       depends on FB_NVIDIA
1063       select FB_DDC
1064       help
1065          This enables I2C support for nVidia Chipsets.  This is used
1066          only for getting EDID information from the attached display
1067          allowing for robust video mode handling and switching.
1068
1069          Because fbdev-2.6 requires that drivers must be able to
1070          independently validate video mode parameters, you should say Y
1071          here.
1072
1073config FB_NVIDIA_DEBUG
1074        bool "Lots of debug output"
1075        depends on FB_NVIDIA
1076        default n
1077        help
1078          Say Y here if you want the nVidia driver to output all sorts
1079          of debugging information to provide to the maintainer when
1080          something goes wrong.
1081
1082config FB_NVIDIA_BACKLIGHT
1083        bool "Support for backlight control"
1084        depends on FB_NVIDIA
1085        default y
1086        help
1087          Say Y here if you want to control the backlight of your display.
1088
1089config FB_RIVA
1090        tristate "nVidia Riva support"
1091        depends on FB && PCI
1092        select FB_BACKLIGHT if FB_RIVA_BACKLIGHT
1093        select FB_MODE_HELPERS
1094        select FB_CFB_FILLRECT
1095        select FB_CFB_COPYAREA
1096        select FB_CFB_IMAGEBLIT
1097        select BITREVERSE
1098        select VGASTATE
1099        help
1100          This driver supports graphics boards with the nVidia Riva/Geforce
1101          chips.
1102          Say Y if you have such a graphics board.
1103
1104          To compile this driver as a module, choose M here: the
1105          module will be called rivafb.
1106
1107config FB_RIVA_I2C
1108       bool "Enable DDC Support"
1109       depends on FB_RIVA
1110       select FB_DDC
1111       help
1112          This enables I2C support for nVidia Chipsets.  This is used
1113          only for getting EDID information from the attached display
1114          allowing for robust video mode handling and switching.
1115
1116          Because fbdev-2.6 requires that drivers must be able to
1117          independently validate video mode parameters, you should say Y
1118          here.
1119
1120config FB_RIVA_DEBUG
1121        bool "Lots of debug output"
1122        depends on FB_RIVA
1123        default n
1124        help
1125          Say Y here if you want the Riva driver to output all sorts
1126          of debugging information to provide to the maintainer when
1127          something goes wrong.
1128
1129config FB_RIVA_BACKLIGHT
1130        bool "Support for backlight control"
1131        depends on FB_RIVA
1132        default y
1133        help
1134          Say Y here if you want to control the backlight of your display.
1135
1136config FB_I740
1137        tristate "Intel740 support"
1138        depends on FB && PCI
1139        select FB_MODE_HELPERS
1140        select FB_CFB_FILLRECT
1141        select FB_CFB_COPYAREA
1142        select FB_CFB_IMAGEBLIT
1143        select VGASTATE
1144        select FB_DDC
1145        help
1146          This driver supports graphics cards based on Intel740 chip.
1147
1148config FB_I810
1149        tristate "Intel 810/815 support"
1150        depends on FB && PCI && X86_32 && AGP_INTEL
1151        select FB_MODE_HELPERS
1152        select FB_CFB_FILLRECT
1153        select FB_CFB_COPYAREA
1154        select FB_CFB_IMAGEBLIT
1155        select VGASTATE
1156        help
1157          This driver supports the on-board graphics built in to the Intel 810 
1158          and 815 chipsets.  Say Y if you have and plan to use such a board.
1159
1160          To compile this driver as a module, choose M here: the
1161          module will be called i810fb.
1162
1163          For more information, please read 
1164          <file:Documentation/fb/intel810.txt>
1165
1166config FB_I810_GTF
1167        bool "use VESA Generalized Timing Formula"
1168        depends on FB_I810
1169        help
1170          If you say Y, then the VESA standard, Generalized Timing Formula 
1171          or GTF, will be used to calculate the required video timing values
1172          per video mode.  Since the GTF allows nondiscrete timings 
1173          (nondiscrete being a range of values as opposed to discrete being a
1174          set of values), you'll be able to use any combination of horizontal 
1175          and vertical resolutions, and vertical refresh rates without having
1176          to specify your own timing parameters.  This is especially useful
1177          to maximize the performance of an aging display, or if you just 
1178          have a display with nonstandard dimensions. A VESA compliant 
1179          monitor is recommended, but can still work with non-compliant ones.
1180          If you need or want this, then select this option. The timings may 
1181          not be compliant with Intel's recommended values. Use at your own 
1182          risk.
1183
1184          If you say N, the driver will revert to discrete video timings 
1185          using a set recommended by Intel in their documentation.
1186  
1187          If unsure, say N.
1188
1189config FB_I810_I2C
1190        bool "Enable DDC Support"
1191        depends on FB_I810 && FB_I810_GTF
1192        select FB_DDC
1193        help
1194
1195config FB_LE80578
1196        tristate "Intel LE80578 (Vermilion) support"
1197        depends on FB && PCI && X86
1198        select FB_MODE_HELPERS
1199        select FB_CFB_FILLRECT
1200        select FB_CFB_COPYAREA
1201        select FB_CFB_IMAGEBLIT
1202        help
1203          This driver supports the LE80578 (Vermilion Range) chipset
1204
1205config FB_CARILLO_RANCH
1206        tristate "Intel Carillo Ranch support"
1207        depends on FB_LE80578 && FB && PCI && X86
1208        help
1209          This driver supports the LE80578 (Carillo Ranch) board
1210
1211config FB_INTEL
1212        tristate "Intel 830M/845G/852GM/855GM/865G/915G/945G/945GM/965G/965GM support"
1213        depends on FB && PCI && X86 && AGP_INTEL && EXPERT
1214        select FB_MODE_HELPERS
1215        select FB_CFB_FILLRECT
1216        select FB_CFB_COPYAREA
1217        select FB_CFB_IMAGEBLIT
1218        select FB_BOOT_VESA_SUPPORT if FB_INTEL = y
1219        depends on !DRM_I915
1220        help
1221          This driver supports the on-board graphics built in to the Intel
1222          830M/845G/852GM/855GM/865G/915G/915GM/945G/945GM/965G/965GM chipsets.
1223          Say Y if you have and plan to use such a board.
1224
1225          To make FB_INTELFB=Y work you need to say AGP_INTEL=y too.
1226
1227          To compile this driver as a module, choose M here: the
1228          module will be called intelfb.
1229
1230          For more information, please read <file:Documentation/fb/intelfb.txt>
1231
1232config FB_INTEL_DEBUG
1233        bool "Intel driver Debug Messages"
1234        depends on FB_INTEL
1235        ---help---
1236          Say Y here if you want the Intel driver to output all sorts
1237          of debugging information to provide to the maintainer when
1238          something goes wrong.
1239
1240config FB_INTEL_I2C
1241        bool "DDC/I2C for Intel framebuffer support"
1242        depends on FB_INTEL
1243        select FB_DDC
1244        default y
1245        help
1246          Say Y here if you want DDC/I2C support for your on-board Intel graphics.
1247
1248config FB_MATROX
1249        tristate "Matrox acceleration"
1250        depends on FB && PCI
1251        select FB_CFB_FILLRECT
1252        select FB_CFB_COPYAREA
1253        select FB_CFB_IMAGEBLIT
1254        select FB_TILEBLITTING
1255        select FB_MACMODES if PPC_PMAC
1256        ---help---
1257          Say Y here if you have a Matrox Millennium, Matrox Millennium II,
1258          Matrox Mystique, Matrox Mystique 220, Matrox Productiva G100, Matrox
1259          Mystique G200, Matrox Millennium G200, Matrox Marvel G200 video,
1260          Matrox G400, G450 or G550 card in your box.
1261
1262          To compile this driver as a module, choose M here: the
1263          module will be called matroxfb.
1264
1265          You can pass several parameters to the driver at boot time or at
1266          module load time. The parameters look like "video=matroxfb:XXX", and
1267          are described in <file:Documentation/fb/matroxfb.txt>.
1268
1269config FB_MATROX_MILLENIUM
1270        bool "Millennium I/II support"
1271        depends on FB_MATROX
1272        help
1273          Say Y here if you have a Matrox Millennium or Matrox Millennium II
1274          video card. If you select "Advanced lowlevel driver options" below,
1275          you should check 4 bpp packed pixel, 8 bpp packed pixel, 16 bpp
1276          packed pixel, 24 bpp packed pixel and 32 bpp packed pixel. You can
1277          also use font widths different from 8.
1278
1279config FB_MATROX_MYSTIQUE
1280        bool "Mystique support"
1281        depends on FB_MATROX
1282        help
1283          Say Y here if you have a Matrox Mystique or Matrox Mystique 220
1284          video card. If you select "Advanced lowlevel driver options" below,
1285          you should check 8 bpp packed pixel, 16 bpp packed pixel, 24 bpp
1286          packed pixel and 32 bpp packed pixel. You can also use font widths
1287          different from 8.
1288
1289config FB_MATROX_G
1290        bool "G100/G200/G400/G450/G550 support"
1291        depends on FB_MATROX
1292        ---help---
1293          Say Y here if you have a Matrox G100, G200, G400, G450 or G550 based
1294          video card. If you select "Advanced lowlevel driver options", you
1295          should check 8 bpp packed pixel, 16 bpp packed pixel, 24 bpp packed
1296          pixel and 32 bpp packed pixel. You can also use font widths
1297          different from 8.
1298
1299          If you need support for G400 secondary head, you must say Y to
1300          "Matrox I2C support" and "G400 second head support" right below.
1301          G450/G550 secondary head and digital output are supported without
1302          additional modules.
1303
1304          The driver starts in monitor mode. You must use the matroxset tool 
1305          (available at <ftp://platan.vc.cvut.cz/pub/linux/matrox-latest/>) to 
1306          swap primary and secondary head outputs, or to change output mode.  
1307          Secondary head driver always start in 640x480 resolution and you 
1308          must use fbset to change it.
1309
1310          Do not forget that second head supports only 16 and 32 bpp
1311          packed pixels, so it is a good idea to compile them into the kernel
1312          too. You can use only some font widths, as the driver uses generic
1313          painting procedures (the secondary head does not use acceleration
1314          engine).
1315
1316          G450/G550 hardware can display TV picture only from secondary CRTC,
1317          and it performs no scaling, so picture must have 525 or 625 lines.
1318
1319config FB_MATROX_I2C
1320        tristate "Matrox I2C support"
1321        depends on FB_MATROX
1322        select FB_DDC
1323        ---help---
1324          This drivers creates I2C buses which are needed for accessing the
1325          DDC (I2C) bus present on all Matroxes, an I2C bus which
1326          interconnects Matrox optional devices, like MGA-TVO on G200 and
1327          G400, and the secondary head DDC bus, present on G400 only.
1328
1329          You can say Y or M here if you want to experiment with monitor
1330          detection code. You must say Y or M here if you want to use either
1331          second head of G400 or MGA-TVO on G200 or G400.
1332
1333          If you compile it as module, it will create a module named
1334          i2c-matroxfb.
1335
1336config FB_MATROX_MAVEN
1337        tristate "G400 second head support"
1338        depends on FB_MATROX_G && FB_MATROX_I2C
1339        ---help---
1340          WARNING !!! This support does not work with G450 !!!
1341
1342          Say Y or M here if you want to use a secondary head (meaning two
1343          monitors in parallel) on G400 or MGA-TVO add-on on G200. Secondary
1344          head is not compatible with accelerated XFree 3.3.x SVGA servers -
1345          secondary head output is blanked while you are in X. With XFree
1346          3.9.17 preview you can use both heads if you use SVGA over fbdev or
1347          the fbdev driver on first head and the fbdev driver on second head.
1348
1349          If you compile it as module, two modules are created,
1350          matroxfb_crtc2 and matroxfb_maven. Matroxfb_maven is needed for
1351          both G200 and G400, matroxfb_crtc2 is needed only by G400. You must
1352          also load i2c-matroxfb to get it to run.
1353
1354          The driver starts in monitor mode and you must use the matroxset
1355          tool (available at
1356          <ftp://platan.vc.cvut.cz/pub/linux/matrox-latest/>) to switch it to
1357          PAL or NTSC or to swap primary and secondary head outputs.
1358          Secondary head driver also always start in 640x480 resolution, you
1359          must use fbset to change it.
1360
1361          Also do not forget that second head supports only 16 and 32 bpp
1362          packed pixels, so it is a good idea to compile them into the kernel
1363          too.  You can use only some font widths, as the driver uses generic
1364          painting procedures (the secondary head does not use acceleration
1365          engine).
1366
1367config FB_RADEON
1368        tristate "ATI Radeon display support"
1369        depends on FB && PCI
1370        select FB_BACKLIGHT if FB_RADEON_BACKLIGHT
1371        select FB_MODE_HELPERS
1372        select FB_CFB_FILLRECT
1373        select FB_CFB_COPYAREA
1374        select FB_CFB_IMAGEBLIT
1375        select FB_MACMODES if PPC_OF
1376        help
1377          Choose this option if you want to use an ATI Radeon graphics card as
1378          a framebuffer device.  There are both PCI and AGP versions.  You
1379          don't need to choose this to run the Radeon in plain VGA mode.
1380
1381          There is a product page at
1382          http://products.amd.com/en-us/GraphicCardResult.aspx
1383
1384config FB_RADEON_I2C
1385        bool "DDC/I2C for ATI Radeon support"
1386        depends on FB_RADEON
1387        select FB_DDC
1388        default y
1389        help
1390          Say Y here if you want DDC/I2C support for your Radeon board. 
1391
1392config FB_RADEON_BACKLIGHT
1393        bool "Support for backlight control"
1394        depends on FB_RADEON
1395        default y
1396        help
1397          Say Y here if you want to control the backlight of your display.
1398
1399config FB_RADEON_DEBUG
1400        bool "Lots of debug output from Radeon driver"
1401        depends on FB_RADEON
1402        default n
1403        help
1404          Say Y here if you want the Radeon driver to output all sorts
1405          of debugging information to provide to the maintainer when
1406          something goes wrong.
1407
1408config FB_ATY128
1409        tristate "ATI Rage128 display support"
1410        depends on FB && PCI
1411        select FB_CFB_FILLRECT
1412        select FB_CFB_COPYAREA
1413        select FB_CFB_IMAGEBLIT
1414        select FB_BACKLIGHT if FB_ATY128_BACKLIGHT
1415        select FB_MACMODES if PPC_PMAC
1416        help
1417          This driver supports graphics boards with the ATI Rage128 chips.
1418          Say Y if you have such a graphics board and read
1419          <file:Documentation/fb/aty128fb.txt>.
1420
1421          To compile this driver as a module, choose M here: the
1422          module will be called aty128fb.
1423
1424config FB_ATY128_BACKLIGHT
1425        bool "Support for backlight control"
1426        depends on FB_ATY128
1427        default y
1428        help
1429          Say Y here if you want to control the backlight of your display.
1430
1431config FB_ATY
1432        tristate "ATI Mach64 display support" if PCI || ATARI
1433        depends on FB && !SPARC32
1434        select FB_CFB_FILLRECT
1435        select FB_CFB_COPYAREA
1436        select FB_CFB_IMAGEBLIT
1437        select FB_BACKLIGHT if FB_ATY_BACKLIGHT
1438        select FB_MACMODES if PPC
1439        help
1440          This driver supports graphics boards with the ATI Mach64 chips.
1441          Say Y if you have such a graphics board.
1442
1443          To compile this driver as a module, choose M here: the
1444          module will be called atyfb.
1445
1446config FB_ATY_CT
1447        bool "Mach64 CT/VT/GT/LT (incl. 3D RAGE) support"
1448        depends on PCI && FB_ATY
1449        default y if SPARC64 && PCI
1450        help
1451          Say Y here to support use of ATI's 64-bit Rage boards (or other
1452          boards based on the Mach64 CT, VT, GT, and LT chipsets) as a
1453          framebuffer device.  The ATI product support page for these boards
1454          is at <http://support.ati.com/products/pc/mach64/mach64.html>.
1455
1456config FB_ATY_GENERIC_LCD
1457        bool "Mach64 generic LCD support"
1458        depends on FB_ATY_CT
1459        help
1460          Say Y if you have a laptop with an ATI Rage LT PRO, Rage Mobility,
1461          Rage XC, or Rage XL chipset.
1462
1463config FB_ATY_GX
1464        bool "Mach64 GX support" if PCI
1465        depends on FB_ATY
1466        default y if ATARI
1467        help
1468          Say Y here to support use of the ATI Mach64 Graphics Expression
1469          board (or other boards based on the Mach64 GX chipset) as a
1470          framebuffer device.  The ATI product support page for these boards
1471          is at
1472          <http://support.ati.com/products/pc/mach64/graphics_xpression.html>.
1473
1474config FB_ATY_BACKLIGHT
1475        bool "Support for backlight control"
1476        depends on FB_ATY
1477        default y
1478        help
1479          Say Y here if you want to control the backlight of your display.
1480
1481config FB_S3
1482        tristate "S3 Trio/Virge support"
1483        depends on FB && PCI
1484        select FB_CFB_FILLRECT
1485        select FB_CFB_COPYAREA
1486        select FB_CFB_IMAGEBLIT
1487        select FB_TILEBLITTING
1488        select FB_SVGALIB
1489        select VGASTATE
1490        select FONT_8x16 if FRAMEBUFFER_CONSOLE
1491        ---help---
1492          Driver for graphics boards with S3 Trio / S3 Virge chip.
1493
1494config FB_S3_DDC
1495        bool "DDC for S3 support"
1496        depends on FB_S3
1497        select FB_DDC
1498        default y
1499        help
1500          Say Y here if you want DDC support for your S3 graphics card.
1501
1502config FB_SAVAGE
1503        tristate "S3 Savage support"
1504        depends on FB && PCI
1505        select FB_MODE_HELPERS
1506        select FB_CFB_FILLRECT
1507        select FB_CFB_COPYAREA
1508        select FB_CFB_IMAGEBLIT
1509        select VGASTATE
1510        help
1511          This driver supports notebooks and computers with S3 Savage PCI/AGP
1512          chips.
1513
1514          Say Y if you have such a graphics card.
1515
1516          To compile this driver as a module, choose M here; the module
1517          will be called savagefb.
1518
1519config FB_SAVAGE_I2C
1520       bool "Enable DDC2 Support"
1521       depends on FB_SAVAGE
1522       select FB_DDC
1523       help
1524          This enables I2C support for S3 Savage Chipsets.  This is used
1525          only for getting EDID information from the attached display
1526          allowing for robust video mode handling and switching.
1527
1528          Because fbdev-2.6 requires that drivers must be able to
1529          independently validate video mode parameters, you should say Y
1530          here.
1531
1532config FB_SAVAGE_ACCEL
1533       bool "Enable Console Acceleration"
1534       depends on FB_SAVAGE
1535       default n
1536       help
1537          This option will compile in console acceleration support. If
1538          the resulting framebuffer console has bothersome glitches, then
1539          choose N here.
1540
1541config FB_SIS
1542        tristate "SiS/XGI display support"
1543        depends on FB && PCI
1544        select FB_CFB_FILLRECT
1545        select FB_CFB_COPYAREA
1546        select FB_CFB_IMAGEBLIT
1547        select FB_BOOT_VESA_SUPPORT if FB_SIS = y
1548        help
1549          This is the frame buffer device driver for the SiS 300, 315, 330
1550          and 340 series as well as XGI V3XT, V5, V8, Z7 graphics chipsets.
1551          Specs available at <http://www.sis.com> and <http://www.xgitech.com>.
1552
1553          To compile this driver as a module, choose M here; the module
1554          will be called sisfb.
1555
1556config FB_SIS_300
1557        bool "SiS 300 series support"
1558        depends on FB_SIS
1559        help
1560          Say Y here to support use of the SiS 300/305, 540, 630 and 730.
1561
1562config FB_SIS_315
1563        bool "SiS 315/330/340 series and XGI support"
1564        depends on FB_SIS
1565        help
1566          Say Y here to support use of the SiS 315, 330 and 340 series
1567          (315/H/PRO, 55x, 650, 651, 740, 330, 661, 741, 760, 761) as well
1568          as XGI V3XT, V5, V8 and Z7.
1569
1570config FB_VIA
1571       tristate "VIA UniChrome (Pro) and Chrome9 display support"
1572       depends on FB && PCI && X86
1573       select FB_CFB_FILLRECT
1574       select FB_CFB_COPYAREA
1575       select FB_CFB_IMAGEBLIT
1576       select I2C_ALGOBIT
1577       select I2C
1578       select GPIOLIB
1579       help
1580          This is the frame buffer device driver for Graphics chips of VIA
1581          UniChrome (Pro) Family (CLE266,PM800/CN400,P4M800CE/P4M800Pro/
1582          CN700/VN800,CX700/VX700,P4M890) and Chrome9 Family (K8M890,CN896
1583          /P4M900,VX800)
1584          Say Y if you have a VIA UniChrome graphics board.
1585
1586          To compile this driver as a module, choose M here: the
1587          module will be called viafb.
1588
1589if FB_VIA
1590
1591config FB_VIA_DIRECT_PROCFS
1592        bool "direct hardware access via procfs (DEPRECATED)(DANGEROUS)"
1593        depends on FB_VIA
1594        default n
1595        help
1596          Allow direct hardware access to some output registers via procfs.
1597          This is dangerous but may provide the only chance to get the
1598          correct output device configuration.
1599          Its use is strongly discouraged.
1600
1601config FB_VIA_X_COMPATIBILITY
1602        bool "X server compatibility"
1603        depends on FB_VIA
1604        default n
1605        help
1606          This option reduces the functionality (power saving, ...) of the
1607          framebuffer to avoid negative impact on the OpenChrome X server.
1608          If you use any X server other than fbdev you should enable this
1609          otherwise it should be safe to disable it and allow using all
1610          features.
1611
1612endif
1613
1614config FB_NEOMAGIC
1615        tristate "NeoMagic display support"
1616        depends on FB && PCI
1617        select FB_MODE_HELPERS
1618        select FB_CFB_FILLRECT
1619        select FB_CFB_COPYAREA
1620        select FB_CFB_IMAGEBLIT
1621        select VGASTATE
1622        help
1623          This driver supports notebooks with NeoMagic PCI chips.
1624          Say Y if you have such a graphics card. 
1625
1626          To compile this driver as a module, choose M here: the
1627          module will be called neofb.
1628
1629config FB_KYRO
1630        tristate "IMG Kyro support"
1631        depends on FB && PCI
1632        select FB_CFB_FILLRECT
1633        select FB_CFB_COPYAREA
1634        select FB_CFB_IMAGEBLIT
1635        help
1636          Say Y here if you have a STG4000 / Kyro / PowerVR 3 based
1637          graphics board.
1638
1639          To compile this driver as a module, choose M here: the
1640          module will be called kyrofb.
1641
1642config FB_3DFX
1643        tristate "3Dfx Banshee/Voodoo3/Voodoo5 display support"
1644        depends on FB && PCI
1645        select FB_CFB_IMAGEBLIT
1646        select FB_CFB_FILLRECT
1647        select FB_CFB_COPYAREA
1648        select FB_MODE_HELPERS
1649        help
1650          This driver supports graphics boards with the 3Dfx Banshee,
1651          Voodoo3 or VSA-100 (aka Voodoo4/5) chips. Say Y if you have
1652          such a graphics board.
1653
1654          To compile this driver as a module, choose M here: the
1655          module will be called tdfxfb.
1656
1657config FB_3DFX_ACCEL
1658        bool "3Dfx Acceleration functions"
1659        depends on FB_3DFX
1660        ---help---
1661        This will compile the 3Dfx Banshee/Voodoo3/VSA-100 frame buffer
1662        device driver with acceleration functions.
1663
1664config FB_3DFX_I2C
1665        bool "Enable DDC/I2C support"
1666        depends on FB_3DFX
1667        select FB_DDC
1668        default y
1669        help
1670          Say Y here if you want DDC/I2C support for your 3dfx Voodoo3.
1671
1672config FB_VOODOO1
1673        tristate "3Dfx Voodoo Graphics (sst1) support"
1674        depends on FB && PCI
1675        select FB_CFB_FILLRECT
1676        select FB_CFB_COPYAREA
1677        select FB_CFB_IMAGEBLIT
1678        ---help---
1679          Say Y here if you have a 3Dfx Voodoo Graphics (Voodoo1/sst1) or 
1680          Voodoo2 (cvg) based graphics card.
1681
1682          To compile this driver as a module, choose M here: the
1683          module will be called sstfb.
1684
1685          WARNING: Do not use any application that uses the 3D engine
1686          (namely glide) while using this driver.
1687          Please read the <file:Documentation/fb/sstfb.txt> for supported
1688          options and other important info  support.
1689
1690config FB_VT8623
1691        tristate "VIA VT8623 support"
1692        depends on FB && PCI
1693        select FB_CFB_FILLRECT
1694        select FB_CFB_COPYAREA
1695        select FB_CFB_IMAGEBLIT
1696        select FB_TILEBLITTING
1697        select FB_SVGALIB
1698        select VGASTATE
1699        select FONT_8x16 if FRAMEBUFFER_CONSOLE
1700        ---help---
1701          Driver for CastleRock integrated graphics core in the
1702          VIA VT8623 [Apollo CLE266] chipset.
1703
1704config FB_TRIDENT
1705        tristate "Trident/CyberXXX/CyberBlade support"
1706        depends on FB && PCI
1707        select FB_CFB_FILLRECT
1708        select FB_CFB_COPYAREA
1709        select FB_CFB_IMAGEBLIT
1710        ---help---
1711          This is the frame buffer device driver for Trident PCI/AGP chipsets.
1712          Supported chipset families are TGUI 9440/96XX, 3DImage, Blade3D
1713          and Blade XP.
1714          There are also integrated versions of these chips called CyberXXXX,
1715          CyberImage or CyberBlade. These chips are mostly found in laptops
1716          but also on some motherboards including early VIA EPIA motherboards.
1717          For more information, read <file:Documentation/fb/tridentfb.txt>
1718
1719          Say Y if you have such a graphics board.
1720
1721          To compile this driver as a module, choose M here: the
1722          module will be called tridentfb.
1723
1724config FB_ARK
1725        tristate "ARK 2000PV support"
1726        depends on FB && PCI
1727        select FB_CFB_FILLRECT
1728        select FB_CFB_COPYAREA
1729        select FB_CFB_IMAGEBLIT
1730        select FB_TILEBLITTING
1731        select FB_SVGALIB
1732        select VGASTATE
1733        select FONT_8x16 if FRAMEBUFFER_CONSOLE
1734        ---help---
1735          Driver for PCI graphics boards with ARK 2000PV chip
1736          and ICS 5342 RAMDAC.
1737
1738config FB_PM3
1739        tristate "Permedia3 support"
1740        depends on FB && PCI
1741        select FB_CFB_FILLRECT
1742        select FB_CFB_COPYAREA
1743        select FB_CFB_IMAGEBLIT
1744        help
1745          This is the frame buffer device driver for the 3DLabs Permedia3
1746          chipset, used in Formac ProFormance III, 3DLabs Oxygen VX1 &
1747          similar boards, 3DLabs Permedia3 Create!, Appian Jeronimo 2000
1748          and maybe other boards.
1749
1750config FB_CARMINE
1751        tristate "Fujitsu carmine frame buffer support"
1752        depends on FB && PCI
1753        select FB_CFB_FILLRECT
1754        select FB_CFB_COPYAREA
1755        select FB_CFB_IMAGEBLIT
1756        help
1757          This is the frame buffer device driver for the Fujitsu Carmine chip.
1758          The driver provides two independent frame buffer devices.
1759
1760choice
1761        depends on FB_CARMINE
1762        prompt "DRAM timing"
1763        default FB_CARMINE_DRAM_EVAL
1764
1765config FB_CARMINE_DRAM_EVAL
1766        bool "Eval board timings"
1767        help
1768          Use timings which work on the eval card.
1769
1770config CARMINE_DRAM_CUSTOM
1771        bool "Custom board timings"
1772        help
1773          Use custom board timings.
1774endchoice
1775
1776config FB_AU1100
1777        bool "Au1100 LCD Driver"
1778        depends on (FB = y) && MIPS_ALCHEMY
1779        select FB_CFB_FILLRECT
1780        select FB_CFB_COPYAREA
1781        select FB_CFB_IMAGEBLIT
1782        help
1783          This is the framebuffer driver for the AMD Au1100 SOC.  It can drive
1784          various panels and CRTs by passing in kernel cmd line option
1785          au1100fb:panel=<name>.
1786
1787config FB_AU1200
1788        bool "Au1200/Au1300 LCD Driver"
1789        depends on (FB = y) && MIPS_ALCHEMY
1790        select FB_SYS_FILLRECT
1791        select FB_SYS_COPYAREA
1792        select FB_SYS_IMAGEBLIT
1793        select FB_SYS_FOPS
1794        help
1795          This is the framebuffer driver for the Au1200/Au1300 SOCs.
1796          It can drive various panels and CRTs by passing in kernel cmd line
1797          option au1200fb:panel=<name>.
1798
1799config FB_VT8500
1800        bool "VT8500 LCD Driver"
1801        depends on (FB = y) && ARM && ARCH_VT8500
1802        select FB_WMT_GE_ROPS
1803        select FB_SYS_IMAGEBLIT
1804        help
1805          This is the framebuffer driver for VIA VT8500 integrated LCD
1806          controller.
1807
1808config FB_WM8505
1809        bool "WM8505 frame buffer support"
1810        depends on (FB = y) && ARM && ARCH_VT8500
1811        select FB_WMT_GE_ROPS
1812        select FB_SYS_IMAGEBLIT
1813        help
1814          This is the framebuffer driver for WonderMedia WM8505/WM8650
1815          integrated LCD controller.
1816
1817source "drivers/video/geode/Kconfig"
1818
1819config FB_HIT
1820        tristate "HD64461 Frame Buffer support"
1821        depends on FB && HD64461
1822        select FB_CFB_FILLRECT
1823        select FB_CFB_COPYAREA
1824        select FB_CFB_IMAGEBLIT
1825        help
1826          This is the frame buffer device driver for the Hitachi HD64461 LCD
1827          frame buffer card.
1828
1829config FB_PMAG_AA
1830        bool "PMAG-AA TURBOchannel framebuffer support"
1831        depends on (FB = y) && TC
1832        select FB_CFB_FILLRECT
1833        select FB_CFB_COPYAREA
1834        select FB_CFB_IMAGEBLIT
1835        help
1836          Support for the PMAG-AA TURBOchannel framebuffer card (1280x1024x1)
1837          used mainly in the MIPS-based DECstation series.
1838
1839config FB_PMAG_BA
1840        tristate "PMAG-BA TURBOchannel framebuffer support"
1841        depends on FB && TC
1842        select FB_CFB_FILLRECT
1843        select FB_CFB_COPYAREA
1844        select FB_CFB_IMAGEBLIT
1845        help
1846          Support for the PMAG-BA TURBOchannel framebuffer card (1024x864x8)
1847          used mainly in the MIPS-based DECstation series.
1848
1849config FB_PMAGB_B
1850        tristate "PMAGB-B TURBOchannel framebuffer support"
1851        depends on FB && TC
1852        select FB_CFB_FILLRECT
1853        select FB_CFB_COPYAREA
1854        select FB_CFB_IMAGEBLIT
1855        help
1856          Support for the PMAGB-B TURBOchannel framebuffer card used mainly
1857          in the MIPS-based DECstation series. The card is currently only
1858          supported in 1280x1024x8 mode.
1859
1860config FB_MAXINE
1861        bool "Maxine (Personal DECstation) onboard framebuffer support"
1862        depends on (FB = y) && MACH_DECSTATION
1863        select FB_CFB_FILLRECT
1864        select FB_CFB_COPYAREA
1865        select FB_CFB_IMAGEBLIT
1866        help
1867          Support for the onboard framebuffer (1024x768x8) in the Personal
1868          DECstation series (Personal DECstation 5000/20, /25, /33, /50,
1869          Codename "Maxine").
1870
1871config FB_G364
1872        bool "G364 frame buffer support"
1873        depends on (FB = y) && (MIPS_MAGNUM_4000 || OLIVETTI_M700)
1874        select FB_CFB_FILLRECT
1875        select FB_CFB_COPYAREA
1876        select FB_CFB_IMAGEBLIT
1877        help
1878          The G364 driver is the framebuffer used in MIPS Magnum 4000 and
1879          Olivetti M700-10 systems.
1880
1881config FB_68328
1882        bool "Motorola 68328 native frame buffer support"
1883        depends on (FB = y) && (M68328 || M68EZ328 || M68VZ328)
1884        select FB_CFB_FILLRECT
1885        select FB_CFB_COPYAREA
1886        select FB_CFB_IMAGEBLIT
1887        help
1888          Say Y here if you want to support the built-in frame buffer of
1889          the Motorola 68328 CPU family.
1890
1891config FB_PXA168
1892        tristate "PXA168/910 LCD framebuffer support"
1893        depends on FB && (CPU_PXA168 || CPU_PXA910)
1894        select FB_CFB_FILLRECT
1895        select FB_CFB_COPYAREA
1896        select FB_CFB_IMAGEBLIT
1897        ---help---
1898          Frame buffer driver for the built-in LCD controller in the Marvell
1899          MMP processor.
1900
1901config FB_PXA
1902        tristate "PXA LCD framebuffer support"
1903        depends on FB && ARCH_PXA
1904        select FB_CFB_FILLRECT
1905        select FB_CFB_COPYAREA
1906        select FB_CFB_IMAGEBLIT
1907        ---help---
1908          Frame buffer driver for the built-in LCD controller in the Intel
1909          PXA2x0 processor.
1910
1911          This driver is also available as a module ( = code which can be
1912          inserted and removed from the running kernel whenever you want). The
1913          module will be called pxafb. If you want to compile it as a module,
1914          say M here and read <file:Documentation/kbuild/modules.txt>.
1915
1916          If unsure, say N.
1917
1918config FB_PXA_OVERLAY
1919        bool "Support PXA27x/PXA3xx Overlay(s) as framebuffer"
1920        default n
1921        depends on FB_PXA && (PXA27x || PXA3xx)
1922
1923config FB_PXA_SMARTPANEL
1924        bool "PXA Smartpanel LCD support"
1925        default n
1926        depends on FB_PXA
1927
1928config FB_PXA_PARAMETERS
1929        bool "PXA LCD command line parameters"
1930        default n
1931        depends on FB_PXA
1932        ---help---
1933          Enable the use of kernel command line or module parameters
1934          to configure the physical properties of the LCD panel when
1935          using the PXA LCD driver.
1936
1937          This option allows you to override the panel parameters
1938          supplied by the platform in order to support multiple
1939          different models of flatpanel. If you will only be using a
1940          single model of flatpanel then you can safely leave this
1941          option disabled.
1942
1943          <file:Documentation/fb/pxafb.txt> describes the available parameters.
1944
1945config PXA3XX_GCU
1946        tristate "PXA3xx 2D graphics accelerator driver"
1947        depends on FB_PXA
1948        help
1949          Kernelspace driver for the 2D graphics controller unit (GCU)
1950          found on PXA3xx processors. There is a counterpart driver in the
1951          DirectFB suite, see http://www.directfb.org/
1952
1953          If you compile this as a module, it will be called pxa3xx_gcu.
1954
1955config FB_MBX
1956        tristate "2700G LCD framebuffer support"
1957        depends on FB && ARCH_PXA
1958        select FB_CFB_FILLRECT
1959        select FB_CFB_COPYAREA
1960        select FB_CFB_IMAGEBLIT
1961        ---help---
1962          Framebuffer driver for the Intel 2700G (Marathon) Graphics
1963          Accelerator
1964
1965config FB_MBX_DEBUG
1966       bool "Enable debugging info via debugfs"
1967       depends on FB_MBX && DEBUG_FS
1968       default n
1969       ---help---
1970         Enable this if you want debugging information using the debug
1971         filesystem (debugfs)
1972
1973         If unsure, say N.
1974
1975config FB_FSL_DIU
1976        tristate "Freescale DIU framebuffer support"
1977        depends on FB && FSL_SOC
1978        select FB_MODE_HELPERS
1979        select FB_CFB_FILLRECT
1980        select FB_CFB_COPYAREA
1981        select FB_CFB_IMAGEBLIT
1982        select PPC_LIB_RHEAP
1983        ---help---
1984          Framebuffer driver for the Freescale SoC DIU
1985
1986config FB_W100
1987        tristate "W100 frame buffer support"
1988        depends on FB && ARCH_PXA
1989        select FB_CFB_FILLRECT
1990        select FB_CFB_COPYAREA
1991        select FB_CFB_IMAGEBLIT
1992        ---help---
1993          Frame buffer driver for the w100 as found on the Sharp SL-Cxx series.
1994          It can also drive the w3220 chip found on iPAQ hx4700.
1995
1996          This driver is also available as a module ( = code which can be
1997          inserted and removed from the running kernel whenever you want). The
1998          module will be called w100fb. If you want to compile it as a module,
1999          say M here and read <file:Documentation/kbuild/modules.txt>.
2000
2001          If unsure, say N.
2002
2003config FB_SH_MOBILE_LCDC
2004        tristate "SuperH Mobile LCDC framebuffer support"
2005        depends on FB && (SUPERH || ARCH_SHMOBILE) && HAVE_CLK
2006        select FB_SYS_FILLRECT
2007        select FB_SYS_COPYAREA
2008        select FB_SYS_IMAGEBLIT
2009        select FB_SYS_FOPS
2010        select FB_DEFERRED_IO
2011        select FB_BACKLIGHT
2012        select SH_MIPI_DSI if SH_LCD_MIPI_DSI
2013        ---help---
2014          Frame buffer driver for the on-chip SH-Mobile LCD controller.
2015
2016config FB_SH_MOBILE_HDMI
2017        tristate "SuperH Mobile HDMI controller support"
2018        depends on FB_SH_MOBILE_LCDC
2019        select FB_MODE_HELPERS
2020        select SOUND
2021        select SND
2022        select SND_SOC
2023        ---help---
2024          Driver for the on-chip SH-Mobile HDMI controller.
2025
2026config FB_TMIO
2027        tristate "Toshiba Mobile IO FrameBuffer support"
2028        depends on FB && MFD_CORE
2029        select FB_CFB_FILLRECT
2030        select FB_CFB_COPYAREA
2031        select FB_CFB_IMAGEBLIT
2032        ---help---
2033          Frame buffer driver for the Toshiba Mobile IO integrated as found
2034          on the Sharp SL-6000 series
2035
2036          This driver is also available as a module ( = code which can be
2037          inserted and removed from the running kernel whenever you want). The
2038          module will be called tmiofb. If you want to compile it as a module,
2039          say M here and read <file:Documentation/kbuild/modules.txt>.
2040
2041          If unsure, say N.
2042
2043config FB_TMIO_ACCELL
2044        bool "tmiofb acceleration"
2045        depends on FB_TMIO
2046        default y
2047
2048config FB_S3C
2049        tristate "Samsung S3C framebuffer support"
2050        depends on FB && (CPU_S3C2416 || ARCH_S3C64XX || ARCH_S5P64X0 || \
2051                ARCH_S5PC100 || ARCH_S5PV210 || ARCH_EXYNOS)
2052        select FB_CFB_FILLRECT
2053        select FB_CFB_COPYAREA
2054        select FB_CFB_IMAGEBLIT
2055        ---help---
2056          Frame buffer driver for the built-in FB controller in the Samsung
2057          SoC line from the S3C2443 onwards, including the S3C2416, S3C2450,
2058          and the S3C64XX series such as the S3C6400 and S3C6410.
2059
2060          These chips all have the same basic framebuffer design with the
2061          actual capabilities depending on the chip. For instance the S3C6400
2062          and S3C6410 support 4 hardware windows whereas the S3C24XX series
2063          currently only have two.
2064
2065          Currently the support is only for the S3C6400 and S3C6410 SoCs.
2066
2067config FB_S3C_DEBUG_REGWRITE
2068       bool "Debug register writes"
2069       depends on FB_S3C
2070       ---help---
2071         Show all register writes via pr_debug()
2072
2073config FB_S3C2410
2074        tristate "S3C2410 LCD framebuffer support"
2075        depends on FB && ARCH_S3C24XX
2076        select FB_CFB_FILLRECT
2077        select FB_CFB_COPYAREA
2078        select FB_CFB_IMAGEBLIT
2079        ---help---
2080          Frame buffer driver for the built-in LCD controller in the Samsung
2081          S3C2410 processor.
2082
2083          This driver is also available as a module ( = code which can be
2084          inserted and removed from the running kernel whenever you want). The
2085          module will be called s3c2410fb. If you want to compile it as a module,
2086          say M here and read <file:Documentation/kbuild/modules.txt>.
2087
2088          If unsure, say N.
2089config FB_S3C2410_DEBUG
2090        bool "S3C2410 lcd debug messages"
2091        depends on FB_S3C2410
2092        help
2093          Turn on debugging messages. Note that you can set/unset at run time
2094          through sysfs
2095
2096config FB_NUC900
2097        bool "NUC900 LCD framebuffer support"
2098        depends on FB && ARCH_W90X900
2099        select FB_CFB_FILLRECT
2100        select FB_CFB_COPYAREA
2101        select FB_CFB_IMAGEBLIT
2102        ---help---
2103          Frame buffer driver for the built-in LCD controller in the Nuvoton
2104          NUC900 processor
2105
2106config GPM1040A0_320X240
2107        bool "Giantplus Technology GPM1040A0 320x240 Color TFT LCD"
2108        depends on FB_NUC900
2109
2110config FB_NUC900_DEBUG
2111        bool "NUC900 lcd debug messages"
2112        depends on FB_NUC900
2113        help
2114          Turn on debugging messages. Note that you can set/unset at run time
2115          through sysfs
2116
2117config FB_SM501
2118        tristate "Silicon Motion SM501 framebuffer support"
2119        depends on FB && MFD_SM501
2120        select FB_CFB_FILLRECT
2121        select FB_CFB_COPYAREA
2122        select FB_CFB_IMAGEBLIT
2123        ---help---
2124          Frame buffer driver for the CRT and LCD controllers in the Silicon
2125          Motion SM501.
2126
2127          This driver is also available as a module ( = code which can be
2128          inserted and removed from the running kernel whenever you want). The
2129          module will be called sm501fb. If you want to compile it as a module,
2130          say M here and read <file:Documentation/kbuild/modules.txt>.
2131
2132          If unsure, say N.
2133
2134config FB_SMSCUFX
2135        tristate "SMSC UFX6000/7000 USB Framebuffer support"
2136        depends on FB && USB
2137        select FB_MODE_HELPERS
2138        select FB_SYS_FILLRECT
2139        select FB_SYS_COPYAREA
2140        select FB_SYS_IMAGEBLIT
2141        select FB_SYS_FOPS
2142        select FB_DEFERRED_IO
2143        ---help---
2144          This is a kernel framebuffer driver for SMSC UFX USB devices.
2145          Supports fbdev clients like xf86-video-fbdev, kdrive, fbi, and
2146          mplayer -vo fbdev. Supports both UFX6000 (USB 2.0) and UFX7000
2147          (USB 3.0) devices.
2148          To compile as a module, choose M here: the module name is smscufx.
2149
2150config FB_UDL
2151        tristate "Displaylink USB Framebuffer support"
2152        depends on FB && USB
2153        select FB_MODE_HELPERS
2154        select FB_SYS_FILLRECT
2155        select FB_SYS_COPYAREA
2156        select FB_SYS_IMAGEBLIT
2157        select FB_SYS_FOPS
2158        select FB_DEFERRED_IO
2159        ---help---
2160          This is a kernel framebuffer driver for DisplayLink USB devices.
2161          Supports fbdev clients like xf86-video-fbdev, kdrive, fbi, and
2162          mplayer -vo fbdev. Supports all USB 2.0 era DisplayLink devices.
2163          To compile as a module, choose M here: the module name is udlfb.
2164
2165config FB_IBM_GXT4500
2166        tristate "Framebuffer support for IBM GXT4000P/4500P/6000P/6500P adaptors"
2167        depends on FB && PPC
2168        select FB_CFB_FILLRECT
2169        select FB_CFB_COPYAREA
2170        select FB_CFB_IMAGEBLIT
2171        ---help---
2172          Say Y here to enable support for the IBM GXT4000P/6000P and
2173          GXT4500P/6500P display adaptor based on Raster Engine RC1000,
2174          found on some IBM System P (pSeries) machines. This driver
2175          doesn't use Geometry Engine GT1000.
2176
2177config FB_PS3
2178        tristate "PS3 GPU framebuffer driver"
2179        depends on FB && PS3_PS3AV
2180        select FB_SYS_FILLRECT
2181        select FB_SYS_COPYAREA
2182        select FB_SYS_IMAGEBLIT
2183        select FB_SYS_FOPS
2184        select VT_HW_CONSOLE_BINDING if FRAMEBUFFER_CONSOLE
2185        ---help---
2186          Include support for the virtual frame buffer in the PS3 platform.
2187
2188config FB_PS3_DEFAULT_SIZE_M
2189        int "PS3 default frame buffer size (in MiB)"
2190        depends on FB_PS3
2191        default 9
2192        ---help---
2193          This is the default size (in MiB) of the virtual frame buffer in
2194          the PS3.
2195          The default value can be overridden on the kernel command line
2196          using the "ps3fb" option (e.g. "ps3fb=9M");
2197
2198config FB_XILINX
2199        tristate "Xilinx frame buffer support"
2200        depends on FB && (XILINX_VIRTEX || MICROBLAZE)
2201        select FB_CFB_FILLRECT
2202        select FB_CFB_COPYAREA
2203        select FB_CFB_IMAGEBLIT
2204        ---help---
2205          Include support for the Xilinx ML300/ML403 reference design
2206          framebuffer. ML300 carries a 640*480 LCD display on the board,
2207          ML403 uses a standard DB15 VGA connector.
2208
2209config FB_GOLDFISH
2210        tristate "Goldfish Framebuffer"
2211        depends on FB
2212        select FB_CFB_FILLRECT
2213        select FB_CFB_COPYAREA
2214        select FB_CFB_IMAGEBLIT
2215        ---help---
2216          Framebuffer driver for Goldfish Virtual Platform
2217
2218config FB_COBALT
2219        tristate "Cobalt server LCD frame buffer support"
2220        depends on FB && (MIPS_COBALT || MIPS_SEAD3)
2221
2222config FB_SH7760
2223        bool "SH7760/SH7763/SH7720/SH7721 LCDC support"
2224        depends on FB && (CPU_SUBTYPE_SH7760 || CPU_SUBTYPE_SH7763 \
2225                || CPU_SUBTYPE_SH7720 || CPU_SUBTYPE_SH7721)
2226        select FB_CFB_FILLRECT
2227        select FB_CFB_COPYAREA
2228        select FB_CFB_IMAGEBLIT
2229        ---help---
2230          Support for the SH7760/SH7763/SH7720/SH7721 integrated
2231          (D)STN/TFT LCD Controller.
2232          Supports display resolutions up to 1024x1024 pixel, grayscale and
2233          color operation, with depths ranging from 1 bpp to 8 bpp monochrome
2234          and 8, 15 or 16 bpp color; 90 degrees clockwise display rotation for
2235          panels <= 320 pixel horizontal resolution.
2236
2237config FB_DA8XX
2238        tristate "DA8xx/OMAP-L1xx Framebuffer support"
2239        depends on FB && ARCH_DAVINCI_DA8XX
2240        select FB_CFB_FILLRECT
2241        select FB_CFB_COPYAREA
2242        select FB_CFB_IMAGEBLIT
2243        select FB_CFB_REV_PIXELS_IN_BYTE
2244        ---help---
2245          This is the frame buffer device driver for the TI LCD controller
2246          found on DA8xx/OMAP-L1xx SoCs.
2247          If unsure, say N.
2248
2249config FB_VIRTUAL
2250        tristate "Virtual Frame Buffer support (ONLY FOR TESTING!)"
2251        depends on FB
2252        select FB_SYS_FILLRECT
2253        select FB_SYS_COPYAREA
2254        select FB_SYS_IMAGEBLIT
2255        select FB_SYS_FOPS
2256        ---help---
2257          This is a `virtual' frame buffer device. It operates on a chunk of
2258          unswappable kernel memory instead of on the memory of a graphics
2259          board. This means you cannot see any output sent to this frame
2260          buffer device, while it does consume precious memory. The main use
2261          of this frame buffer device is testing and debugging the frame
2262          buffer subsystem. Do NOT enable it for normal systems! To protect
2263          the innocent, it has to be enabled explicitly at boot time using the
2264          kernel option `video=vfb:'.
2265
2266          To compile this driver as a module, choose M here: the
2267          module will be called vfb. In order to load it, you must use
2268          the vfb_enable=1 option.
2269
2270          If unsure, say N.
2271
2272config XEN_FBDEV_FRONTEND
2273        tristate "Xen virtual frame buffer support"
2274        depends on FB && XEN
2275        select FB_SYS_FILLRECT
2276        select FB_SYS_COPYAREA
2277        select FB_SYS_IMAGEBLIT
2278        select FB_SYS_FOPS
2279        select FB_DEFERRED_IO
2280        select INPUT_XEN_KBDDEV_FRONTEND
2281        select XEN_XENBUS_FRONTEND
2282        default y
2283        help
2284          This driver implements the front-end of the Xen virtual
2285          frame buffer driver.  It communicates with a back-end
2286          in another domain.
2287
2288config FB_METRONOME
2289        tristate "E-Ink Metronome/8track controller support"
2290        depends on FB
2291        select FB_SYS_FILLRECT
2292        select FB_SYS_COPYAREA
2293        select FB_SYS_IMAGEBLIT
2294        select FB_SYS_FOPS
2295        select FB_DEFERRED_IO
2296        help
2297          This driver implements support for the E-Ink Metronome
2298          controller. The pre-release name for this device was 8track
2299          and could also have been called by some vendors as PVI-nnnn.
2300
2301config FB_MB862XX
2302        tristate "Fujitsu MB862xx GDC support"
2303        depends on FB
2304        depends on PCI || (OF && PPC)
2305        select FB_CFB_FILLRECT
2306        select FB_CFB_COPYAREA
2307        select FB_CFB_IMAGEBLIT
2308        ---help---
2309          Frame buffer driver for Fujitsu Carmine/Coral-P(A)/Lime controllers.
2310
2311choice
2312        prompt "GDC variant"
2313        depends on FB_MB862XX
2314
2315config FB_MB862XX_PCI_GDC
2316        bool "Carmine/Coral-P(A) GDC"
2317        depends on PCI
2318        ---help---
2319          This enables framebuffer support for Fujitsu Carmine/Coral-P(A)
2320          PCI graphics controller devices.
2321
2322config FB_MB862XX_LIME
2323        bool "Lime GDC"
2324        depends on OF && PPC
2325        select FB_FOREIGN_ENDIAN
2326        select FB_LITTLE_ENDIAN
2327        ---help---
2328          Framebuffer support for Fujitsu Lime GDC on host CPU bus.
2329
2330endchoice
2331
2332config FB_MB862XX_I2C
2333        bool "Support I2C bus on MB862XX GDC"
2334        depends on FB_MB862XX && I2C
2335        default y
2336        help
2337          Selecting this option adds Coral-P(A)/Lime GDC I2C bus adapter
2338          driver to support accessing I2C devices on controller's I2C bus.
2339          These are usually some video decoder chips.
2340
2341config FB_EP93XX
2342        tristate "EP93XX frame buffer support"
2343        depends on FB && ARCH_EP93XX
2344        select FB_CFB_FILLRECT
2345        select FB_CFB_COPYAREA
2346        select FB_CFB_IMAGEBLIT
2347        ---help---
2348          Framebuffer driver for the Cirrus Logic EP93XX series of processors.
2349          This driver is also available as a module. The module will be called
2350          ep93xx-fb.
2351
2352config FB_PRE_INIT_FB
2353        bool "Don't reinitialize, use bootloader's GDC/Display configuration"
2354        depends on FB && FB_MB862XX_LIME
2355        ---help---
2356          Select this option if display contents should be inherited as set by
2357          the bootloader.
2358
2359config FB_MSM
2360        tristate "MSM Framebuffer support"
2361        depends on FB && ARCH_MSM
2362        select FB_CFB_FILLRECT
2363        select FB_CFB_COPYAREA
2364        select FB_CFB_IMAGEBLIT
2365
2366config FB_MX3
2367        tristate "MX3 Framebuffer support"
2368        depends on FB && MX3_IPU
2369        select FB_CFB_FILLRECT
2370        select FB_CFB_COPYAREA
2371        select FB_CFB_IMAGEBLIT
2372        default y
2373        help
2374          This is a framebuffer device for the i.MX31 LCD Controller. So
2375          far only synchronous displays are supported. If you plan to use
2376          an LCD display with your i.MX31 system, say Y here.
2377
2378config FB_BROADSHEET
2379        tristate "E-Ink Broadsheet/Epson S1D13521 controller support"
2380        depends on FB
2381        select FB_SYS_FILLRECT
2382        select FB_SYS_COPYAREA
2383        select FB_SYS_IMAGEBLIT
2384        select FB_SYS_FOPS
2385        select FB_DEFERRED_IO
2386        help
2387          This driver implements support for the E-Ink Broadsheet
2388          controller. The release name for this device was Epson S1D13521
2389          and could also have been called by other names when coupled with
2390          a bridge adapter.
2391
2392config FB_AUO_K190X
2393        tristate "AUO-K190X EPD controller support"
2394        depends on FB
2395        select FB_SYS_FILLRECT
2396        select FB_SYS_COPYAREA
2397        select FB_SYS_IMAGEBLIT
2398        select FB_SYS_FOPS
2399        select FB_DEFERRED_IO
2400        help
2401          Provides support for epaper controllers from the K190X series
2402          of AUO. These controllers can be used to drive epaper displays
2403          from Sipix.
2404
2405          This option enables the common support, shared by the individual
2406          controller drivers. You will also have to enable the driver
2407          for the controller type used in your device.
2408
2409config FB_AUO_K1900
2410        tristate "AUO-K1900 EPD controller support"
2411        depends on FB && FB_AUO_K190X
2412        help
2413          This driver implements support for the AUO K1900 epd-controller.
2414          This controller can drive Sipix epaper displays but can only do
2415          serial updates, reducing the number of possible frames per second.
2416
2417config FB_AUO_K1901
2418        tristate "AUO-K1901 EPD controller support"
2419        depends on FB && FB_AUO_K190X
2420        help
2421          This driver implements support for the AUO K1901 epd-controller.
2422          This controller can drive Sipix epaper displays and supports
2423          concurrent updates, making higher frames per second possible.
2424
2425config FB_JZ4740
2426        tristate "JZ4740 LCD framebuffer support"
2427        depends on FB && MACH_JZ4740
2428        select FB_SYS_FILLRECT
2429        select FB_SYS_COPYAREA
2430        select FB_SYS_IMAGEBLIT
2431        help
2432          Framebuffer support for the JZ4740 SoC.
2433
2434config FB_MXS
2435        tristate "MXS LCD framebuffer support"
2436        depends on FB && ARCH_MXS
2437        select FB_CFB_FILLRECT
2438        select FB_CFB_COPYAREA
2439        select FB_CFB_IMAGEBLIT
2440        help
2441          Framebuffer support for the MXS SoC.
2442
2443config FB_PUV3_UNIGFX
2444        tristate "PKUnity v3 Unigfx framebuffer support"
2445        depends on FB && UNICORE32 && ARCH_PUV3
2446        select FB_SYS_FILLRECT
2447        select FB_SYS_COPYAREA
2448        select FB_SYS_IMAGEBLIT
2449        select FB_SYS_FOPS
2450        help
2451          Choose this option if you want to use the Unigfx device as a
2452          framebuffer device. Without the support of PCI & AGP.
2453
2454source "drivers/video/omap/Kconfig"
2455source "drivers/video/omap2/Kconfig"
2456source "drivers/video/exynos/Kconfig"
2457source "drivers/video/mmp/Kconfig"
2458source "drivers/video/backlight/Kconfig"
2459
2460if VT
2461        source "drivers/video/console/Kconfig"
2462endif
2463
2464if FB || SGI_NEWPORT_CONSOLE
2465        source "drivers/video/logo/Kconfig"
2466endif
2467
2468config FB_SH_MOBILE_MERAM
2469        tristate "SuperH Mobile MERAM read ahead support"
2470        depends on (SUPERH || ARCH_SHMOBILE)
2471        select GENERIC_ALLOCATOR
2472        ---help---
2473          Enable MERAM support for the SuperH controller.
2474
2475          This will allow for caching of the framebuffer to provide more
2476          reliable access under heavy main memory bus traffic situations.
2477          Up to 4 memory channels can be configured, allowing 4 RGB or
2478          2 YCbCr framebuffers to be configured.
2479
2480config FB_SSD1307
2481        tristate "Solomon SSD1307 framebuffer support"
2482        depends on FB && I2C
2483        depends on OF
2484        depends on GENERIC_GPIO
2485        select FB_SYS_FOPS
2486        select FB_SYS_FILLRECT
2487        select FB_SYS_COPYAREA
2488        select FB_SYS_IMAGEBLIT
2489        select FB_DEFERRED_IO
2490        select PWM
2491        help
2492          This driver implements support for the Solomon SSD1307
2493          OLED controller over I2C.
2494
2495endmenu
2496
lxr.linux.no kindly hosted by Redpill Linpro AS, provider of Linux consulting and operations services since 1995.