linux/drivers/power/ab8500_bmdata.c
<<
>>
Prefs
   1#include <linux/export.h>
   2#include <linux/power_supply.h>
   3#include <linux/of.h>
   4#include <linux/mfd/abx500.h>
   5#include <linux/mfd/abx500/ab8500.h>
   6#include <linux/mfd/abx500/ab8500-bm.h>
   7
   8/*
   9 * These are the defined batteries that uses a NTC and ID resistor placed
  10 * inside of the battery pack.
  11 * Note that the res_to_temp table must be strictly sorted by falling resistance
  12 * values to work.
  13 */
  14static struct abx500_res_to_temp temp_tbl_A_thermistor[] = {
  15        {-5, 53407},
  16        { 0, 48594},
  17        { 5, 43804},
  18        {10, 39188},
  19        {15, 34870},
  20        {20, 30933},
  21        {25, 27422},
  22        {30, 24347},
  23        {35, 21694},
  24        {40, 19431},
  25        {45, 17517},
  26        {50, 15908},
  27        {55, 14561},
  28        {60, 13437},
  29        {65, 12500},
  30};
  31
  32static struct abx500_res_to_temp temp_tbl_B_thermistor[] = {
  33        {-5, 200000},
  34        { 0, 159024},
  35        { 5, 151921},
  36        {10, 144300},
  37        {15, 136424},
  38        {20, 128565},
  39        {25, 120978},
  40        {30, 113875},
  41        {35, 107397},
  42        {40, 101629},
  43        {45,  96592},
  44        {50,  92253},
  45        {55,  88569},
  46        {60,  85461},
  47        {65,  82869},
  48};
  49
  50static struct abx500_v_to_cap cap_tbl_A_thermistor[] = {
  51        {4171,  100},
  52        {4114,   95},
  53        {4009,   83},
  54        {3947,   74},
  55        {3907,   67},
  56        {3863,   59},
  57        {3830,   56},
  58        {3813,   53},
  59        {3791,   46},
  60        {3771,   33},
  61        {3754,   25},
  62        {3735,   20},
  63        {3717,   17},
  64        {3681,   13},
  65        {3664,    8},
  66        {3651,    6},
  67        {3635,    5},
  68        {3560,    3},
  69        {3408,    1},
  70        {3247,    0},
  71};
  72
  73static struct abx500_v_to_cap cap_tbl_B_thermistor[] = {
  74        {4161,  100},
  75        {4124,   98},
  76        {4044,   90},
  77        {4003,   85},
  78        {3966,   80},
  79        {3933,   75},
  80        {3888,   67},
  81        {3849,   60},
  82        {3813,   55},
  83        {3787,   47},
  84        {3772,   30},
  85        {3751,   25},
  86        {3718,   20},
  87        {3681,   16},
  88        {3660,   14},
  89        {3589,   10},
  90        {3546,    7},
  91        {3495,    4},
  92        {3404,    2},
  93        {3250,    0},
  94};
  95
  96static struct abx500_v_to_cap cap_tbl[] = {
  97        {4186,  100},
  98        {4163,   99},
  99        {4114,   95},
 100        {4068,   90},
 101        {3990,   80},
 102        {3926,   70},
 103        {3898,   65},
 104        {3866,   60},
 105        {3833,   55},
 106        {3812,   50},
 107        {3787,   40},
 108        {3768,   30},
 109        {3747,   25},
 110        {3730,   20},
 111        {3705,   15},
 112        {3699,   14},
 113        {3684,   12},
 114        {3672,    9},
 115        {3657,    7},
 116        {3638,    6},
 117        {3556,    4},
 118        {3424,    2},
 119        {3317,    1},
 120        {3094,    0},
 121};
 122
 123/*
 124 * Note that the res_to_temp table must be strictly sorted by falling
 125 * resistance values to work.
 126 */
 127static struct abx500_res_to_temp temp_tbl[] = {
 128        {-5, 214834},
 129        { 0, 162943},
 130        { 5, 124820},
 131        {10,  96520},
 132        {15,  75306},
 133        {20,  59254},
 134        {25,  47000},
 135        {30,  37566},
 136        {35,  30245},
 137        {40,  24520},
 138        {45,  20010},
 139        {50,  16432},
 140        {55,  13576},
 141        {60,  11280},
 142        {65,   9425},
 143};
 144
 145/*
 146 * Note that the batres_vs_temp table must be strictly sorted by falling
 147 * temperature values to work.
 148 */
 149static struct batres_vs_temp temp_to_batres_tbl_thermistor[] = {
 150        { 40, 120},
 151        { 30, 135},
 152        { 20, 165},
 153        { 10, 230},
 154        { 00, 325},
 155        {-10, 445},
 156        {-20, 595},
 157};
 158
 159/*
 160 * Note that the batres_vs_temp table must be strictly sorted by falling
 161 * temperature values to work.
 162 */
 163static struct batres_vs_temp temp_to_batres_tbl_ext_thermistor[] = {
 164        { 60, 300},
 165        { 30, 300},
 166        { 20, 300},
 167        { 10, 300},
 168        { 00, 300},
 169        {-10, 300},
 170        {-20, 300},
 171};
 172
 173/* battery resistance table for LI ION 9100 battery */
 174static struct batres_vs_temp temp_to_batres_tbl_9100[] = {
 175        { 60, 180},
 176        { 30, 180},
 177        { 20, 180},
 178        { 10, 180},
 179        { 00, 180},
 180        {-10, 180},
 181        {-20, 180},
 182};
 183
 184static struct abx500_battery_type bat_type_thermistor[] = {
 185        [BATTERY_UNKNOWN] = {
 186                /* First element always represent the UNKNOWN battery */
 187                .name = POWER_SUPPLY_TECHNOLOGY_UNKNOWN,
 188                .resis_high = 0,
 189                .resis_low = 0,
 190                .battery_resistance = 300,
 191                .charge_full_design = 612,
 192                .nominal_voltage = 3700,
 193                .termination_vol = 4050,
 194                .termination_curr = 200,
 195                .recharge_cap = 95,
 196                .normal_cur_lvl = 400,
 197                .normal_vol_lvl = 4100,
 198                .maint_a_cur_lvl = 400,
 199                .maint_a_vol_lvl = 4050,
 200                .maint_a_chg_timer_h = 60,
 201                .maint_b_cur_lvl = 400,
 202                .maint_b_vol_lvl = 4000,
 203                .maint_b_chg_timer_h = 200,
 204                .low_high_cur_lvl = 300,
 205                .low_high_vol_lvl = 4000,
 206                .n_temp_tbl_elements = ARRAY_SIZE(temp_tbl),
 207                .r_to_t_tbl = temp_tbl,
 208                .n_v_cap_tbl_elements = ARRAY_SIZE(cap_tbl),
 209                .v_to_cap_tbl = cap_tbl,
 210                .n_batres_tbl_elements = ARRAY_SIZE(temp_to_batres_tbl_thermistor),
 211                .batres_tbl = temp_to_batres_tbl_thermistor,
 212        },
 213        {
 214                .name = POWER_SUPPLY_TECHNOLOGY_LIPO,
 215                .resis_high = 53407,
 216                .resis_low = 12500,
 217                .battery_resistance = 300,
 218                .charge_full_design = 900,
 219                .nominal_voltage = 3600,
 220                .termination_vol = 4150,
 221                .termination_curr = 80,
 222                .recharge_cap = 95,
 223                .normal_cur_lvl = 700,
 224                .normal_vol_lvl = 4200,
 225                .maint_a_cur_lvl = 600,
 226                .maint_a_vol_lvl = 4150,
 227                .maint_a_chg_timer_h = 60,
 228                .maint_b_cur_lvl = 600,
 229                .maint_b_vol_lvl = 4100,
 230                .maint_b_chg_timer_h = 200,
 231                .low_high_cur_lvl = 300,
 232                .low_high_vol_lvl = 4000,
 233                .n_temp_tbl_elements = ARRAY_SIZE(temp_tbl_A_thermistor),
 234                .r_to_t_tbl = temp_tbl_A_thermistor,
 235                .n_v_cap_tbl_elements = ARRAY_SIZE(cap_tbl_A_thermistor),
 236                .v_to_cap_tbl = cap_tbl_A_thermistor,
 237                .n_batres_tbl_elements = ARRAY_SIZE(temp_to_batres_tbl_thermistor),
 238                .batres_tbl = temp_to_batres_tbl_thermistor,
 239
 240        },
 241        {
 242                .name = POWER_SUPPLY_TECHNOLOGY_LIPO,
 243                .resis_high = 200000,
 244                .resis_low = 82869,
 245                .battery_resistance = 300,
 246                .charge_full_design = 900,
 247                .nominal_voltage = 3600,
 248                .termination_vol = 4150,
 249                .termination_curr = 80,
 250                .recharge_cap = 95,
 251                .normal_cur_lvl = 700,
 252                .normal_vol_lvl = 4200,
 253                .maint_a_cur_lvl = 600,
 254                .maint_a_vol_lvl = 4150,
 255                .maint_a_chg_timer_h = 60,
 256                .maint_b_cur_lvl = 600,
 257                .maint_b_vol_lvl = 4100,
 258                .maint_b_chg_timer_h = 200,
 259                .low_high_cur_lvl = 300,
 260                .low_high_vol_lvl = 4000,
 261                .n_temp_tbl_elements = ARRAY_SIZE(temp_tbl_B_thermistor),
 262                .r_to_t_tbl = temp_tbl_B_thermistor,
 263                .n_v_cap_tbl_elements = ARRAY_SIZE(cap_tbl_B_thermistor),
 264                .v_to_cap_tbl = cap_tbl_B_thermistor,
 265                .n_batres_tbl_elements = ARRAY_SIZE(temp_to_batres_tbl_thermistor),
 266                .batres_tbl = temp_to_batres_tbl_thermistor,
 267        },
 268};
 269
 270static struct abx500_battery_type bat_type_ext_thermistor[] = {
 271        [BATTERY_UNKNOWN] = {
 272                /* First element always represent the UNKNOWN battery */
 273                .name = POWER_SUPPLY_TECHNOLOGY_UNKNOWN,
 274                .resis_high = 0,
 275                .resis_low = 0,
 276                .battery_resistance = 300,
 277                .charge_full_design = 612,
 278                .nominal_voltage = 3700,
 279                .termination_vol = 4050,
 280                .termination_curr = 200,
 281                .recharge_cap = 95,
 282                .normal_cur_lvl = 400,
 283                .normal_vol_lvl = 4100,
 284                .maint_a_cur_lvl = 400,
 285                .maint_a_vol_lvl = 4050,
 286                .maint_a_chg_timer_h = 60,
 287                .maint_b_cur_lvl = 400,
 288                .maint_b_vol_lvl = 4000,
 289                .maint_b_chg_timer_h = 200,
 290                .low_high_cur_lvl = 300,
 291                .low_high_vol_lvl = 4000,
 292                .n_temp_tbl_elements = ARRAY_SIZE(temp_tbl),
 293                .r_to_t_tbl = temp_tbl,
 294                .n_v_cap_tbl_elements = ARRAY_SIZE(cap_tbl),
 295                .v_to_cap_tbl = cap_tbl,
 296                .n_batres_tbl_elements = ARRAY_SIZE(temp_to_batres_tbl_thermistor),
 297                .batres_tbl = temp_to_batres_tbl_thermistor,
 298        },
 299/*
 300 * These are the batteries that doesn't have an internal NTC resistor to measure
 301 * its temperature. The temperature in this case is measure with a NTC placed
 302 * near the battery but on the PCB.
 303 */
 304        {
 305                .name = POWER_SUPPLY_TECHNOLOGY_LIPO,
 306                .resis_high = 76000,
 307                .resis_low = 53000,
 308                .battery_resistance = 300,
 309                .charge_full_design = 900,
 310                .nominal_voltage = 3700,
 311                .termination_vol = 4150,
 312                .termination_curr = 100,
 313                .recharge_cap = 95,
 314                .normal_cur_lvl = 700,
 315                .normal_vol_lvl = 4200,
 316                .maint_a_cur_lvl = 600,
 317                .maint_a_vol_lvl = 4150,
 318                .maint_a_chg_timer_h = 60,
 319                .maint_b_cur_lvl = 600,
 320                .maint_b_vol_lvl = 4100,
 321                .maint_b_chg_timer_h = 200,
 322                .low_high_cur_lvl = 300,
 323                .low_high_vol_lvl = 4000,
 324                .n_temp_tbl_elements = ARRAY_SIZE(temp_tbl),
 325                .r_to_t_tbl = temp_tbl,
 326                .n_v_cap_tbl_elements = ARRAY_SIZE(cap_tbl),
 327                .v_to_cap_tbl = cap_tbl,
 328                .n_batres_tbl_elements = ARRAY_SIZE(temp_to_batres_tbl_thermistor),
 329                .batres_tbl = temp_to_batres_tbl_thermistor,
 330        },
 331        {
 332                .name = POWER_SUPPLY_TECHNOLOGY_LION,
 333                .resis_high = 30000,
 334                .resis_low = 10000,
 335                .battery_resistance = 300,
 336                .charge_full_design = 950,
 337                .nominal_voltage = 3700,
 338                .termination_vol = 4150,
 339                .termination_curr = 100,
 340                .recharge_cap = 95,
 341                .normal_cur_lvl = 700,
 342                .normal_vol_lvl = 4200,
 343                .maint_a_cur_lvl = 600,
 344                .maint_a_vol_lvl = 4150,
 345                .maint_a_chg_timer_h = 60,
 346                .maint_b_cur_lvl = 600,
 347                .maint_b_vol_lvl = 4100,
 348                .maint_b_chg_timer_h = 200,
 349                .low_high_cur_lvl = 300,
 350                .low_high_vol_lvl = 4000,
 351                .n_temp_tbl_elements = ARRAY_SIZE(temp_tbl),
 352                .r_to_t_tbl = temp_tbl,
 353                .n_v_cap_tbl_elements = ARRAY_SIZE(cap_tbl),
 354                .v_to_cap_tbl = cap_tbl,
 355                .n_batres_tbl_elements = ARRAY_SIZE(temp_to_batres_tbl_thermistor),
 356                .batres_tbl = temp_to_batres_tbl_thermistor,
 357        },
 358        {
 359                .name = POWER_SUPPLY_TECHNOLOGY_LION,
 360                .resis_high = 95000,
 361                .resis_low = 76001,
 362                .battery_resistance = 300,
 363                .charge_full_design = 950,
 364                .nominal_voltage = 3700,
 365                .termination_vol = 4150,
 366                .termination_curr = 100,
 367                .recharge_cap = 95,
 368                .normal_cur_lvl = 700,
 369                .normal_vol_lvl = 4200,
 370                .maint_a_cur_lvl = 600,
 371                .maint_a_vol_lvl = 4150,
 372                .maint_a_chg_timer_h = 60,
 373                .maint_b_cur_lvl = 600,
 374                .maint_b_vol_lvl = 4100,
 375                .maint_b_chg_timer_h = 200,
 376                .low_high_cur_lvl = 300,
 377                .low_high_vol_lvl = 4000,
 378                .n_temp_tbl_elements = ARRAY_SIZE(temp_tbl),
 379                .r_to_t_tbl = temp_tbl,
 380                .n_v_cap_tbl_elements = ARRAY_SIZE(cap_tbl),
 381                .v_to_cap_tbl = cap_tbl,
 382                .n_batres_tbl_elements = ARRAY_SIZE(temp_to_batres_tbl_thermistor),
 383                .batres_tbl = temp_to_batres_tbl_thermistor,
 384        },
 385};
 386
 387static const struct abx500_bm_capacity_levels cap_levels = {
 388        .critical       = 2,
 389        .low            = 10,
 390        .normal         = 70,
 391        .high           = 95,
 392        .full           = 100,
 393};
 394
 395static const struct abx500_fg_parameters fg = {
 396        .recovery_sleep_timer = 10,
 397        .recovery_total_time = 100,
 398        .init_timer = 1,
 399        .init_discard_time = 5,
 400        .init_total_time = 40,
 401        .high_curr_time = 60,
 402        .accu_charging = 30,
 403        .accu_high_curr = 30,
 404        .high_curr_threshold = 50,
 405        .lowbat_threshold = 3100,
 406        .battok_falling_th_sel0 = 2860,
 407        .battok_raising_th_sel1 = 2860,
 408        .maint_thres = 95,
 409        .user_cap_limit = 15,
 410};
 411
 412static const struct abx500_maxim_parameters maxi_params = {
 413        .ena_maxi = true,
 414        .chg_curr = 910,
 415        .wait_cycles = 10,
 416        .charger_curr_step = 100,
 417};
 418
 419static const struct abx500_bm_charger_parameters chg = {
 420        .usb_volt_max           = 5500,
 421        .usb_curr_max           = 1500,
 422        .ac_volt_max            = 7500,
 423        .ac_curr_max            = 1500,
 424};
 425
 426struct abx500_bm_data ab8500_bm_data = {
 427        .temp_under             = 3,
 428        .temp_low               = 8,
 429        .temp_high              = 43,
 430        .temp_over              = 48,
 431        .main_safety_tmr_h      = 4,
 432        .temp_interval_chg      = 20,
 433        .temp_interval_nochg    = 120,
 434        .usb_safety_tmr_h       = 4,
 435        .bkup_bat_v             = BUP_VCH_SEL_2P6V,
 436        .bkup_bat_i             = BUP_ICH_SEL_150UA,
 437        .no_maintenance         = false,
 438        .capacity_scaling       = false,
 439        .adc_therm              = ABx500_ADC_THERM_BATCTRL,
 440        .chg_unknown_bat        = false,
 441        .enable_overshoot       = false,
 442        .fg_res                 = 100,
 443        .cap_levels             = &cap_levels,
 444        .bat_type               = bat_type_thermistor,
 445        .n_btypes               = 3,
 446        .batt_id                = 0,
 447        .interval_charging      = 5,
 448        .interval_not_charging  = 120,
 449        .temp_hysteresis        = 3,
 450        .gnd_lift_resistance    = 34,
 451        .maxi                   = &maxi_params,
 452        .chg_params             = &chg,
 453        .fg_params              = &fg,
 454};
 455
 456int ab8500_bm_of_probe(struct device *dev,
 457                       struct device_node *np,
 458                       struct abx500_bm_data *bm)
 459{
 460        struct batres_vs_temp *tmp_batres_tbl;
 461        struct device_node *battery_node;
 462        const char *btech;
 463        int i;
 464
 465        /* get phandle to 'battery-info' node */
 466        battery_node = of_parse_phandle(np, "battery", 0);
 467        if (!battery_node) {
 468                dev_err(dev, "battery node or reference missing\n");
 469                return -EINVAL;
 470        }
 471
 472        btech = of_get_property(battery_node, "stericsson,battery-type", NULL);
 473        if (!btech) {
 474                dev_warn(dev, "missing property battery-name/type\n");
 475                return -EINVAL;
 476        }
 477
 478        if (strncmp(btech, "LION", 4) == 0) {
 479                bm->no_maintenance  = true;
 480                bm->chg_unknown_bat = true;
 481                bm->bat_type[BATTERY_UNKNOWN].charge_full_design = 2600;
 482                bm->bat_type[BATTERY_UNKNOWN].termination_vol    = 4150;
 483                bm->bat_type[BATTERY_UNKNOWN].recharge_cap       = 95;
 484                bm->bat_type[BATTERY_UNKNOWN].normal_cur_lvl     = 520;
 485                bm->bat_type[BATTERY_UNKNOWN].normal_vol_lvl     = 4200;
 486        }
 487
 488        if (of_property_read_bool(battery_node, "thermistor-on-batctrl")) {
 489                if (strncmp(btech, "LION", 4) == 0)
 490                        tmp_batres_tbl = temp_to_batres_tbl_9100;
 491                else
 492                        tmp_batres_tbl = temp_to_batres_tbl_thermistor;
 493        } else {
 494                bm->n_btypes   = 4;
 495                bm->bat_type   = bat_type_ext_thermistor;
 496                bm->adc_therm  = ABx500_ADC_THERM_BATTEMP;
 497                tmp_batres_tbl = temp_to_batres_tbl_ext_thermistor;
 498        }
 499
 500        /* select the battery resolution table */
 501        for (i = 0; i < bm->n_btypes; ++i)
 502                bm->bat_type[i].batres_tbl = tmp_batres_tbl;
 503
 504        of_node_put(battery_node);
 505
 506        return 0;
 507}
 508
lxr.linux.no kindly hosted by Redpill Linpro AS, provider of Linux consulting and operations services since 1995.