linux/drivers/leds/Kconfig
<<
>>
Prefs
   1config LEDS_GPIO_REGISTER
   2        bool
   3        help
   4          This option provides the function gpio_led_register_device.
   5          As this function is used by arch code it must not be compiled as a
   6          module.
   7
   8menuconfig NEW_LEDS
   9        bool "LED Support"
  10        help
  11          Say Y to enable Linux LED support.  This allows control of supported
  12          LEDs from both userspace and optionally, by kernel events (triggers).
  13
  14          This is not related to standard keyboard LEDs which are controlled
  15          via the input system.
  16
  17if NEW_LEDS
  18
  19config LEDS_CLASS
  20        tristate "LED Class Support"
  21        help
  22          This option enables the led sysfs class in /sys/class/leds.  You'll
  23          need this to do anything useful with LEDs.  If unsure, say N.
  24
  25comment "LED drivers"
  26
  27config LEDS_88PM860X
  28        tristate "LED Support for Marvell 88PM860x PMIC"
  29        depends on LEDS_CLASS
  30        depends on MFD_88PM860X
  31        help
  32          This option enables support for on-chip LED drivers found on Marvell
  33          Semiconductor 88PM8606 PMIC.
  34
  35config LEDS_ATMEL_PWM
  36        tristate "LED Support using Atmel PWM outputs"
  37        depends on LEDS_CLASS
  38        depends on ATMEL_PWM
  39        help
  40          This option enables support for LEDs driven using outputs
  41          of the dedicated PWM controller found on newer Atmel SOCs.
  42
  43config LEDS_LM3530
  44        tristate "LCD Backlight driver for LM3530"
  45        depends on LEDS_CLASS
  46        depends on I2C
  47        help
  48          This option enables support for the LCD backlight using
  49          LM3530 ambient light sensor chip. This ALS chip can be
  50          controlled manually or using PWM input or using ambient
  51          light automatically.
  52
  53config LEDS_LM3533
  54        tristate "LED support for LM3533"
  55        depends on LEDS_CLASS
  56        depends on MFD_LM3533
  57        help
  58          This option enables support for the LEDs on National Semiconductor /
  59          TI LM3533 Lighting Power chips.
  60
  61          The LEDs can be controlled directly, through PWM input, or by the
  62          ambient-light-sensor interface. The chip supports
  63          hardware-accelerated blinking with maximum on and off periods of 9.8
  64          and 77 seconds respectively.
  65
  66config LEDS_LM3642
  67        tristate "LED support for LM3642 Chip"
  68        depends on LEDS_CLASS && I2C
  69        select REGMAP_I2C
  70        help
  71          This option enables support for LEDs connected to LM3642.
  72          The LM3642 is a 4MHz fixed-frequency synchronous boost
  73          converter plus 1.5A constant current driver for a high-current
  74          white LED.
  75
  76
  77config LEDS_LOCOMO
  78        tristate "LED Support for Locomo device"
  79        depends on LEDS_CLASS
  80        depends on SHARP_LOCOMO
  81        help
  82          This option enables support for the LEDs on Sharp Locomo.
  83          Zaurus models SL-5500 and SL-5600.
  84
  85config LEDS_MIKROTIK_RB532
  86        tristate "LED Support for Mikrotik Routerboard 532"
  87        depends on LEDS_CLASS
  88        depends on MIKROTIK_RB532
  89        help
  90          This option enables support for the so called "User LED" of
  91          Mikrotik's Routerboard 532.
  92
  93config LEDS_S3C24XX
  94        tristate "LED Support for Samsung S3C24XX GPIO LEDs"
  95        depends on LEDS_CLASS
  96        depends on ARCH_S3C24XX
  97        help
  98          This option enables support for LEDs connected to GPIO lines
  99          on Samsung S3C24XX series CPUs, such as the S3C2410 and S3C2440.
 100
 101config LEDS_NET48XX
 102        tristate "LED Support for Soekris net48xx series Error LED"
 103        depends on LEDS_CLASS
 104        depends on SCx200_GPIO
 105        help
 106          This option enables support for the Soekris net4801 and net4826 error
 107          LED.
 108
 109config LEDS_FSG
 110        tristate "LED Support for the Freecom FSG-3"
 111        depends on LEDS_CLASS
 112        depends on MACH_FSG
 113        help
 114          This option enables support for the LEDs on the Freecom FSG-3.
 115
 116config LEDS_WRAP
 117        tristate "LED Support for the WRAP series LEDs"
 118        depends on LEDS_CLASS
 119        depends on SCx200_GPIO
 120        help
 121          This option enables support for the PCEngines WRAP programmable LEDs.
 122
 123config LEDS_COBALT_QUBE
 124        tristate "LED Support for the Cobalt Qube series front LED"
 125        depends on LEDS_CLASS
 126        depends on MIPS_COBALT
 127        help
 128          This option enables support for the front LED on Cobalt Qube series
 129
 130config LEDS_COBALT_RAQ
 131        bool "LED Support for the Cobalt Raq series"
 132        depends on LEDS_CLASS=y && MIPS_COBALT
 133        select LEDS_TRIGGERS
 134        help
 135          This option enables support for the Cobalt Raq series LEDs.
 136
 137config LEDS_SUNFIRE
 138        tristate "LED support for SunFire servers."
 139        depends on LEDS_CLASS
 140        depends on SPARC64
 141        select LEDS_TRIGGERS
 142        help
 143          This option enables support for the Left, Middle, and Right
 144          LEDs on the I/O and CPU boards of SunFire UltraSPARC servers.
 145
 146config LEDS_HP6XX
 147        tristate "LED Support for the HP Jornada 6xx"
 148        depends on LEDS_CLASS
 149        depends on SH_HP6XX
 150        help
 151          This option enables LED support for the handheld
 152          HP Jornada 620/660/680/690.
 153
 154config LEDS_PCA9532
 155        tristate "LED driver for PCA9532 dimmer"
 156        depends on LEDS_CLASS
 157        depends on I2C && INPUT
 158        help
 159          This option enables support for NXP pca9532
 160          LED controller. It is generally only useful
 161          as a platform driver
 162
 163config LEDS_PCA9532_GPIO
 164        bool "Enable GPIO support for PCA9532"
 165        depends on LEDS_PCA9532
 166        depends on GPIOLIB
 167        help
 168          Allow unused pins on PCA9532 to be used as gpio.
 169
 170          To use a pin as gpio pca9532_type in pca9532_platform data needs to
 171          set to PCA9532_TYPE_GPIO.
 172
 173config LEDS_GPIO
 174        tristate "LED Support for GPIO connected LEDs"
 175        depends on LEDS_CLASS
 176        depends on GENERIC_GPIO
 177        help
 178          This option enables support for the LEDs connected to GPIO
 179          outputs. To be useful the particular board must have LEDs
 180          and they must be connected to the GPIO lines.  The LEDs must be
 181          defined as platform devices and/or OpenFirmware platform devices.
 182          The code to use these bindings can be selected below.
 183
 184config LEDS_LP3944
 185        tristate "LED Support for N.S. LP3944 (Fun Light) I2C chip"
 186        depends on LEDS_CLASS
 187        depends on I2C
 188        help
 189          This option enables support for LEDs connected to the National
 190          Semiconductor LP3944 Lighting Management Unit (LMU) also known as
 191          Fun Light Chip.
 192
 193          To compile this driver as a module, choose M here: the
 194          module will be called leds-lp3944.
 195
 196config LEDS_LP55XX_COMMON
 197        tristate "Common Driver for TI/National LP5521 and LP5523/55231"
 198        depends on LEDS_LP5521 || LEDS_LP5523
 199        select FW_LOADER
 200        help
 201          This option supports common operations for LP5521 and LP5523/55231
 202          devices.
 203
 204config LEDS_LP5521
 205        tristate "LED Support for N.S. LP5521 LED driver chip"
 206        depends on LEDS_CLASS && I2C
 207        select LEDS_LP55XX_COMMON
 208        help
 209          If you say yes here you get support for the National Semiconductor
 210          LP5521 LED driver. It is 3 channel chip with programmable engines.
 211          Driver provides direct control via LED class and interface for
 212          programming the engines.
 213
 214config LEDS_LP5523
 215        tristate "LED Support for TI/National LP5523/55231 LED driver chip"
 216        depends on LEDS_CLASS && I2C
 217        select LEDS_LP55XX_COMMON
 218        help
 219          If you say yes here you get support for TI/National Semiconductor
 220          LP5523/55231 LED driver.
 221          It is 9 channel chip with programmable engines.
 222          Driver provides direct control via LED class and interface for
 223          programming the engines.
 224
 225config LEDS_LP8788
 226        tristate "LED support for the TI LP8788 PMIC"
 227        depends on LEDS_CLASS
 228        depends on MFD_LP8788
 229        help
 230          This option enables support for the Keyboard LEDs on the LP8788 PMIC.
 231
 232config LEDS_CLEVO_MAIL
 233        tristate "Mail LED on Clevo notebook"
 234        depends on LEDS_CLASS
 235        depends on X86 && SERIO_I8042 && DMI
 236        help
 237          This driver makes the mail LED accessible from userspace
 238          programs through the leds subsystem. This LED have three
 239          known mode: off, blink at 0.5Hz and blink at 1Hz.
 240
 241          The driver supports two kinds of interface: using ledtrig-timer
 242          or through /sys/class/leds/clevo::mail/brightness. As this LED
 243          cannot change it's brightness it blinks instead. The brightness
 244          value 0 means off, 1..127 means blink at 0.5Hz and 128..255 means
 245          blink at 1Hz.
 246
 247          This module can drive the mail LED for the following notebooks:
 248
 249                Clevo D400P
 250                Clevo D410J
 251                Clevo D410V
 252                Clevo D400V/D470V (not tested, but might work)
 253                Clevo M540N
 254                Clevo M5x0N (not tested, but might work)
 255                Positivo Mobile (Clevo M5x0V)
 256
 257          If your model is not listed here you can try the "nodetect"
 258          module parameter.
 259
 260          To compile this driver as a module, choose M here: the
 261          module will be called leds-clevo-mail.
 262
 263config LEDS_PCA955X
 264        tristate "LED Support for PCA955x I2C chips"
 265        depends on LEDS_CLASS
 266        depends on I2C
 267        help
 268          This option enables support for LEDs connected to PCA955x
 269          LED driver chips accessed via the I2C bus.  Supported
 270          devices include PCA9550, PCA9551, PCA9552, and PCA9553.
 271
 272config LEDS_PCA9633
 273        tristate "LED support for PCA9633 I2C chip"
 274        depends on LEDS_CLASS
 275        depends on I2C
 276        help
 277          This option enables support for LEDs connected to the PCA9633
 278          LED driver chip accessed via the I2C bus.
 279
 280config LEDS_WM831X_STATUS
 281        tristate "LED support for status LEDs on WM831x PMICs"
 282        depends on LEDS_CLASS
 283        depends on MFD_WM831X
 284        help
 285          This option enables support for the status LEDs of the WM831x
 286          series of PMICs.
 287
 288config LEDS_WM8350
 289        tristate "LED Support for WM8350 AudioPlus PMIC"
 290        depends on LEDS_CLASS
 291        depends on MFD_WM8350
 292        help
 293          This option enables support for LEDs driven by the Wolfson
 294          Microelectronics WM8350 AudioPlus PMIC.
 295
 296config LEDS_DA903X
 297        tristate "LED Support for DA9030/DA9034 PMIC"
 298        depends on LEDS_CLASS
 299        depends on PMIC_DA903X
 300        help
 301          This option enables support for on-chip LED drivers found
 302          on Dialog Semiconductor DA9030/DA9034 PMICs.
 303
 304config LEDS_DA9052
 305        tristate "Dialog DA9052/DA9053 LEDS"
 306        depends on LEDS_CLASS
 307        depends on PMIC_DA9052
 308        help
 309          This option enables support for on-chip LED drivers found
 310          on Dialog Semiconductor DA9052-BC and DA9053-AA/Bx PMICs.
 311
 312config LEDS_DAC124S085
 313        tristate "LED Support for DAC124S085 SPI DAC"
 314        depends on LEDS_CLASS
 315        depends on SPI
 316        help
 317          This option enables support for DAC124S085 SPI DAC from NatSemi,
 318          which can be used to control up to four LEDs.
 319
 320config LEDS_PWM
 321        tristate "PWM driven LED Support"
 322        depends on LEDS_CLASS
 323        depends on PWM
 324        help
 325          This option enables support for pwm driven LEDs
 326
 327config LEDS_REGULATOR
 328        tristate "REGULATOR driven LED support"
 329        depends on LEDS_CLASS
 330        depends on REGULATOR
 331        help
 332          This option enables support for regulator driven LEDs.
 333
 334config LEDS_BD2802
 335        tristate "LED driver for BD2802 RGB LED"
 336        depends on LEDS_CLASS
 337        depends on I2C
 338        help
 339          This option enables support for BD2802GU RGB LED driver chips
 340          accessed via the I2C bus.
 341
 342config LEDS_INTEL_SS4200
 343        tristate "LED driver for Intel NAS SS4200 series"
 344        depends on LEDS_CLASS
 345        depends on PCI && DMI
 346        help
 347          This option enables support for the Intel SS4200 series of
 348          Network Attached Storage servers.  You may control the hard
 349          drive or power LEDs on the front panel.  Using this driver
 350          can stop the front LED from blinking after startup.
 351
 352config LEDS_LT3593
 353        tristate "LED driver for LT3593 controllers"
 354        depends on LEDS_CLASS
 355        depends on GENERIC_GPIO
 356        help
 357          This option enables support for LEDs driven by a Linear Technology
 358          LT3593 controller. This controller uses a special one-wire pulse
 359          coding protocol to set the brightness.
 360
 361config LEDS_ADP5520
 362        tristate "LED Support for ADP5520/ADP5501 PMIC"
 363        depends on LEDS_CLASS
 364        depends on PMIC_ADP5520
 365        help
 366          This option enables support for on-chip LED drivers found
 367          on Analog Devices ADP5520/ADP5501 PMICs.
 368
 369          To compile this driver as a module, choose M here: the module will
 370          be called leds-adp5520.
 371
 372config LEDS_DELL_NETBOOKS
 373        tristate "External LED on Dell Business Netbooks"
 374        depends on LEDS_CLASS
 375        depends on X86 && ACPI_WMI
 376        help
 377          This adds support for the Latitude 2100 and similar
 378          notebooks that have an external LED.
 379
 380config LEDS_MC13783
 381        tristate "LED Support for MC13783 PMIC"
 382        depends on LEDS_CLASS
 383        depends on MFD_MC13783
 384        help
 385          This option enable support for on-chip LED drivers found
 386          on Freescale Semiconductor MC13783 PMIC.
 387
 388config LEDS_NS2
 389        tristate "LED support for Network Space v2 GPIO LEDs"
 390        depends on LEDS_CLASS
 391        depends on MACH_NETSPACE_V2 || MACH_INETSPACE_V2 || \
 392                   MACH_NETSPACE_MAX_V2 || MACH_D2NET_V2 || \
 393                   MACH_NETSPACE_V2_DT || MACH_INETSPACE_V2_DT || \
 394                   MACH_NETSPACE_MAX_V2_DT || MACH_NETSPACE_MINI_V2_DT
 395        default y
 396        help
 397          This option enable support for the dual-GPIO LED found on the
 398          Network Space v2 board (and parents). This include Internet Space v2,
 399          Network Space (Max) v2 and d2 Network v2 boards.
 400
 401config LEDS_NETXBIG
 402        tristate "LED support for Big Network series LEDs"
 403        depends on MACH_NET2BIG_V2 || MACH_NET5BIG_V2
 404        depends on LEDS_CLASS
 405        default y
 406        help
 407          This option enable support for LEDs found on the LaCie 2Big
 408          and 5Big Network v2 boards. The LEDs are wired to a CPLD and are
 409          controlled through a GPIO extension bus.
 410
 411config LEDS_ASIC3
 412        bool "LED support for the HTC ASIC3"
 413        depends on LEDS_CLASS=y
 414        depends on MFD_ASIC3
 415        default y
 416        help
 417          This option enables support for the LEDs on the HTC ASIC3. The HTC
 418          ASIC3 LED GPIOs are inputs, not outputs, thus the leds-gpio driver
 419          cannot be used. This driver supports hardware blinking with an on+off
 420          period from 62ms to 125s. Say Y to enable LEDs on the HP iPAQ hx4700.
 421
 422config LEDS_RENESAS_TPU
 423        bool "LED support for Renesas TPU"
 424        depends on LEDS_CLASS=y && HAVE_CLK && GENERIC_GPIO
 425        help
 426          This option enables build of the LED TPU platform driver,
 427          suitable to drive any TPU channel on newer Renesas SoCs.
 428          The driver controls the GPIO pin connected to the LED via
 429          the GPIO framework and expects the LED to be connected to
 430          a pin that can be driven in both GPIO mode and using TPU
 431          pin function. The latter to support brightness control.
 432          Brightness control is supported but hardware blinking is not.
 433
 434config LEDS_TCA6507
 435        tristate "LED Support for TCA6507 I2C chip"
 436        depends on LEDS_CLASS && I2C
 437        help
 438          This option enables support for LEDs connected to TC6507
 439          LED driver chips accessed via the I2C bus.
 440          Driver support brightness control and hardware-assisted blinking.
 441
 442config LEDS_MAX8997
 443        tristate "LED support for MAX8997 PMIC"
 444        depends on LEDS_CLASS && MFD_MAX8997
 445        help
 446          This option enables support for on-chip LED drivers on
 447          MAXIM MAX8997 PMIC.
 448
 449config LEDS_LM355x
 450        tristate "LED support for LM355x Chips, LM3554 and LM3556"
 451        depends on LEDS_CLASS && I2C
 452        select REGMAP_I2C
 453        help
 454          This option enables support for LEDs connected to LM355x.
 455          LM355x includes Torch, Flash and Indicator functions.
 456
 457config LEDS_OT200
 458        tristate "LED support for the Bachmann OT200"
 459        depends on LEDS_CLASS && HAS_IOMEM
 460        help
 461          This option enables support for the LEDs on the Bachmann OT200.
 462          Say Y to enable LEDs on the Bachmann OT200.
 463
 464config LEDS_BLINKM
 465        tristate "LED support for the BlinkM I2C RGB LED"
 466        depends on LEDS_CLASS
 467        depends on I2C
 468        help
 469          This option enables support for the BlinkM RGB LED connected
 470          through I2C. Say Y to enable support for the BlinkM LED.
 471
 472config LEDS_TRIGGERS
 473        bool "LED Trigger support"
 474        depends on LEDS_CLASS
 475        help
 476          This option enables trigger support for the leds class.
 477          These triggers allow kernel events to drive the LEDs and can
 478          be configured via sysfs. If unsure, say Y.
 479
 480comment "LED Triggers"
 481
 482config LEDS_TRIGGER_TIMER
 483        tristate "LED Timer Trigger"
 484        depends on LEDS_TRIGGERS
 485        help
 486          This allows LEDs to be controlled by a programmable timer
 487          via sysfs. Some LED hardware can be programmed to start
 488          blinking the LED without any further software interaction.
 489          For more details read Documentation/leds/leds-class.txt.
 490
 491          If unsure, say Y.
 492
 493config LEDS_TRIGGER_ONESHOT
 494        tristate "LED One-shot Trigger"
 495        depends on LEDS_TRIGGERS
 496        help
 497          This allows LEDs to blink in one-shot pulses with parameters
 498          controlled via sysfs.  It's useful to notify the user on
 499          sporadic events, when there are no clear begin and end trap points,
 500          or on dense events, where this blinks the LED at constant rate if
 501          rearmed continuously.
 502
 503          It also shows how to use the led_blink_set_oneshot() function.
 504
 505          If unsure, say Y.
 506
 507config LEDS_TRIGGER_IDE_DISK
 508        bool "LED IDE Disk Trigger"
 509        depends on IDE_GD_ATA
 510        depends on LEDS_TRIGGERS
 511        help
 512          This allows LEDs to be controlled by IDE disk activity.
 513          If unsure, say Y.
 514
 515config LEDS_TRIGGER_HEARTBEAT
 516        tristate "LED Heartbeat Trigger"
 517        depends on LEDS_TRIGGERS
 518        help
 519          This allows LEDs to be controlled by a CPU load average.
 520          The flash frequency is a hyperbolic function of the 1-minute
 521          load average.
 522          If unsure, say Y.
 523
 524config LEDS_TRIGGER_BACKLIGHT
 525        tristate "LED backlight Trigger"
 526        depends on LEDS_TRIGGERS
 527        help
 528          This allows LEDs to be controlled as a backlight device: they
 529          turn off and on when the display is blanked and unblanked.
 530
 531          If unsure, say N.
 532
 533config LEDS_TRIGGER_CPU
 534        bool "LED CPU Trigger"
 535        depends on LEDS_TRIGGERS
 536        help
 537          This allows LEDs to be controlled by active CPUs. This shows
 538          the active CPUs across an array of LEDs so you can see which
 539          CPUs are active on the system at any given moment.
 540
 541          If unsure, say N.
 542
 543config LEDS_TRIGGER_GPIO
 544        tristate "LED GPIO Trigger"
 545        depends on LEDS_TRIGGERS
 546        depends on GPIOLIB
 547        help
 548          This allows LEDs to be controlled by gpio events. It's good
 549          when using gpios as switches and triggering the needed LEDs
 550          from there. One use case is n810's keypad LEDs that could
 551          be triggered by this trigger when user slides up to show
 552          keypad.
 553
 554          If unsure, say N.
 555
 556config LEDS_TRIGGER_DEFAULT_ON
 557        tristate "LED Default ON Trigger"
 558        depends on LEDS_TRIGGERS
 559        help
 560          This allows LEDs to be initialised in the ON state.
 561          If unsure, say Y.
 562
 563comment "iptables trigger is under Netfilter config (LED target)"
 564        depends on LEDS_TRIGGERS
 565
 566config LEDS_TRIGGER_TRANSIENT
 567        tristate "LED Transient Trigger"
 568        depends on LEDS_TRIGGERS
 569        help
 570          This allows one time activation of a transient state on
 571          GPIO/PWM based hardware.
 572          If unsure, say Y.
 573
 574endif # NEW_LEDS
 575
lxr.linux.no kindly hosted by Redpill Linpro AS, provider of Linux consulting and operations services since 1995.