linux/drivers/leds/Kconfig
<<
>>
Prefs
   1config LEDS_GPIO_REGISTER
   2        bool
   3        help
   4          This option provides the function gpio_led_register_device.
   5          As this function is used by arch code it must not be compiled as a
   6          module.
   7
   8menuconfig NEW_LEDS
   9        bool "LED Support"
  10        help
  11          Say Y to enable Linux LED support.  This allows control of supported
  12          LEDs from both userspace and optionally, by kernel events (triggers).
  13
  14          This is not related to standard keyboard LEDs which are controlled
  15          via the input system.
  16
  17if NEW_LEDS
  18
  19config LEDS_CLASS
  20        tristate "LED Class Support"
  21        help
  22          This option enables the led sysfs class in /sys/class/leds.  You'll
  23          need this to do anything useful with LEDs.  If unsure, say N.
  24
  25comment "LED drivers"
  26
  27config LEDS_88PM860X
  28        tristate "LED Support for Marvell 88PM860x PMIC"
  29        depends on LEDS_CLASS
  30        depends on MFD_88PM860X
  31        help
  32          This option enables support for on-chip LED drivers found on Marvell
  33          Semiconductor 88PM8606 PMIC.
  34
  35config LEDS_ATMEL_PWM
  36        tristate "LED Support using Atmel PWM outputs"
  37        depends on LEDS_CLASS
  38        depends on ATMEL_PWM
  39        help
  40          This option enables support for LEDs driven using outputs
  41          of the dedicated PWM controller found on newer Atmel SOCs.
  42
  43config LEDS_LM3530
  44        tristate "LCD Backlight driver for LM3530"
  45        depends on LEDS_CLASS
  46        depends on I2C
  47        help
  48          This option enables support for the LCD backlight using
  49          LM3530 ambient light sensor chip. This ALS chip can be
  50          controlled manually or using PWM input or using ambient
  51          light automatically.
  52
  53config LEDS_LM3533
  54        tristate "LED support for LM3533"
  55        depends on LEDS_CLASS
  56        depends on MFD_LM3533
  57        help
  58          This option enables support for the LEDs on National Semiconductor /
  59          TI LM3533 Lighting Power chips.
  60
  61          The LEDs can be controlled directly, through PWM input, or by the
  62          ambient-light-sensor interface. The chip supports
  63          hardware-accelerated blinking with maximum on and off periods of 9.8
  64          and 77 seconds respectively.
  65
  66config LEDS_LM3642
  67        tristate "LED support for LM3642 Chip"
  68        depends on LEDS_CLASS && I2C
  69        select REGMAP_I2C
  70        help
  71          This option enables support for LEDs connected to LM3642.
  72          The LM3642 is a 4MHz fixed-frequency synchronous boost
  73          converter plus 1.5A constant current driver for a high-current
  74          white LED.
  75
  76
  77config LEDS_LOCOMO
  78        tristate "LED Support for Locomo device"
  79        depends on LEDS_CLASS
  80        depends on SHARP_LOCOMO
  81        help
  82          This option enables support for the LEDs on Sharp Locomo.
  83          Zaurus models SL-5500 and SL-5600.
  84
  85config LEDS_MIKROTIK_RB532
  86        tristate "LED Support for Mikrotik Routerboard 532"
  87        depends on LEDS_CLASS
  88        depends on MIKROTIK_RB532
  89        help
  90          This option enables support for the so called "User LED" of
  91          Mikrotik's Routerboard 532.
  92
  93config LEDS_S3C24XX
  94        tristate "LED Support for Samsung S3C24XX GPIO LEDs"
  95        depends on LEDS_CLASS
  96        depends on ARCH_S3C24XX
  97        help
  98          This option enables support for LEDs connected to GPIO lines
  99          on Samsung S3C24XX series CPUs, such as the S3C2410 and S3C2440.
 100
 101config LEDS_NET48XX
 102        tristate "LED Support for Soekris net48xx series Error LED"
 103        depends on LEDS_CLASS
 104        depends on SCx200_GPIO
 105        help
 106          This option enables support for the Soekris net4801 and net4826 error
 107          LED.
 108
 109config LEDS_FSG
 110        tristate "LED Support for the Freecom FSG-3"
 111        depends on LEDS_CLASS
 112        depends on MACH_FSG
 113        help
 114          This option enables support for the LEDs on the Freecom FSG-3.
 115
 116config LEDS_WRAP
 117        tristate "LED Support for the WRAP series LEDs"
 118        depends on LEDS_CLASS
 119        depends on SCx200_GPIO
 120        help
 121          This option enables support for the PCEngines WRAP programmable LEDs.
 122
 123config LEDS_COBALT_QUBE
 124        tristate "LED Support for the Cobalt Qube series front LED"
 125        depends on LEDS_CLASS
 126        depends on MIPS_COBALT
 127        help
 128          This option enables support for the front LED on Cobalt Qube series
 129
 130config LEDS_COBALT_RAQ
 131        bool "LED Support for the Cobalt Raq series"
 132        depends on LEDS_CLASS=y && MIPS_COBALT
 133        select LEDS_TRIGGERS
 134        help
 135          This option enables support for the Cobalt Raq series LEDs.
 136
 137config LEDS_SUNFIRE
 138        tristate "LED support for SunFire servers."
 139        depends on LEDS_CLASS
 140        depends on SPARC64
 141        select LEDS_TRIGGERS
 142        help
 143          This option enables support for the Left, Middle, and Right
 144          LEDs on the I/O and CPU boards of SunFire UltraSPARC servers.
 145
 146config LEDS_HP6XX
 147        tristate "LED Support for the HP Jornada 6xx"
 148        depends on LEDS_CLASS
 149        depends on SH_HP6XX
 150        help
 151          This option enables LED support for the handheld
 152          HP Jornada 620/660/680/690.
 153
 154config LEDS_PCA9532
 155        tristate "LED driver for PCA9532 dimmer"
 156        depends on LEDS_CLASS
 157        depends on I2C && INPUT && EXPERIMENTAL
 158        help
 159          This option enables support for NXP pca9532
 160          LED controller. It is generally only useful
 161          as a platform driver
 162
 163config LEDS_PCA9532_GPIO
 164        bool "Enable GPIO support for PCA9532"
 165        depends on LEDS_PCA9532
 166        depends on GPIOLIB
 167        help
 168          Allow unused pins on PCA9532 to be used as gpio.
 169
 170          To use a pin as gpio pca9532_type in pca9532_platform data needs to
 171          set to PCA9532_TYPE_GPIO.
 172
 173config LEDS_GPIO
 174        tristate "LED Support for GPIO connected LEDs"
 175        depends on LEDS_CLASS
 176        depends on GENERIC_GPIO
 177        help
 178          This option enables support for the LEDs connected to GPIO
 179          outputs. To be useful the particular board must have LEDs
 180          and they must be connected to the GPIO lines.  The LEDs must be
 181          defined as platform devices and/or OpenFirmware platform devices.
 182          The code to use these bindings can be selected below.
 183
 184config LEDS_LP3944
 185        tristate "LED Support for N.S. LP3944 (Fun Light) I2C chip"
 186        depends on LEDS_CLASS
 187        depends on I2C
 188        help
 189          This option enables support for LEDs connected to the National
 190          Semiconductor LP3944 Lighting Management Unit (LMU) also known as
 191          Fun Light Chip.
 192
 193          To compile this driver as a module, choose M here: the
 194          module will be called leds-lp3944.
 195
 196config LEDS_LP5521
 197        tristate "LED Support for N.S. LP5521 LED driver chip"
 198        depends on LEDS_CLASS && I2C
 199        help
 200          If you say yes here you get support for the National Semiconductor
 201          LP5521 LED driver. It is 3 channel chip with programmable engines.
 202          Driver provides direct control via LED class and interface for
 203          programming the engines.
 204
 205config LEDS_LP5523
 206        tristate "LED Support for TI/National LP5523/55231 LED driver chip"
 207        depends on LEDS_CLASS && I2C
 208        help
 209          If you say yes here you get support for TI/National Semiconductor
 210          LP5523/55231 LED driver.
 211          It is 9 channel chip with programmable engines.
 212          Driver provides direct control via LED class and interface for
 213          programming the engines.
 214
 215config LEDS_LP8788
 216        tristate "LED support for the TI LP8788 PMIC"
 217        depends on LEDS_CLASS
 218        depends on MFD_LP8788
 219        help
 220          This option enables support for the Keyboard LEDs on the LP8788 PMIC.
 221
 222config LEDS_CLEVO_MAIL
 223        tristate "Mail LED on Clevo notebook"
 224        depends on LEDS_CLASS
 225        depends on X86 && SERIO_I8042 && DMI
 226        help
 227          This driver makes the mail LED accessible from userspace
 228          programs through the leds subsystem. This LED have three
 229          known mode: off, blink at 0.5Hz and blink at 1Hz.
 230
 231          The driver supports two kinds of interface: using ledtrig-timer
 232          or through /sys/class/leds/clevo::mail/brightness. As this LED
 233          cannot change it's brightness it blinks instead. The brightness
 234          value 0 means off, 1..127 means blink at 0.5Hz and 128..255 means
 235          blink at 1Hz.
 236
 237          This module can drive the mail LED for the following notebooks:
 238
 239                Clevo D400P
 240                Clevo D410J
 241                Clevo D410V
 242                Clevo D400V/D470V (not tested, but might work)
 243                Clevo M540N
 244                Clevo M5x0N (not tested, but might work)
 245                Positivo Mobile (Clevo M5x0V)
 246
 247          If your model is not listed here you can try the "nodetect"
 248          module parameter.
 249
 250          To compile this driver as a module, choose M here: the
 251          module will be called leds-clevo-mail.
 252
 253config LEDS_PCA955X
 254        tristate "LED Support for PCA955x I2C chips"
 255        depends on LEDS_CLASS
 256        depends on I2C
 257        help
 258          This option enables support for LEDs connected to PCA955x
 259          LED driver chips accessed via the I2C bus.  Supported
 260          devices include PCA9550, PCA9551, PCA9552, and PCA9553.
 261
 262config LEDS_PCA9633
 263        tristate "LED support for PCA9633 I2C chip"
 264        depends on LEDS_CLASS
 265        depends on I2C
 266        help
 267          This option enables support for LEDs connected to the PCA9633
 268          LED driver chip accessed via the I2C bus.
 269
 270config LEDS_WM831X_STATUS
 271        tristate "LED support for status LEDs on WM831x PMICs"
 272        depends on LEDS_CLASS
 273        depends on MFD_WM831X
 274        help
 275          This option enables support for the status LEDs of the WM831x
 276          series of PMICs.
 277
 278config LEDS_WM8350
 279        tristate "LED Support for WM8350 AudioPlus PMIC"
 280        depends on LEDS_CLASS
 281        depends on MFD_WM8350
 282        help
 283          This option enables support for LEDs driven by the Wolfson
 284          Microelectronics WM8350 AudioPlus PMIC.
 285
 286config LEDS_DA903X
 287        tristate "LED Support for DA9030/DA9034 PMIC"
 288        depends on LEDS_CLASS
 289        depends on PMIC_DA903X
 290        help
 291          This option enables support for on-chip LED drivers found
 292          on Dialog Semiconductor DA9030/DA9034 PMICs.
 293
 294config LEDS_DA9052
 295        tristate "Dialog DA9052/DA9053 LEDS"
 296        depends on LEDS_CLASS
 297        depends on PMIC_DA9052
 298        help
 299          This option enables support for on-chip LED drivers found
 300          on Dialog Semiconductor DA9052-BC and DA9053-AA/Bx PMICs.
 301
 302config LEDS_DAC124S085
 303        tristate "LED Support for DAC124S085 SPI DAC"
 304        depends on LEDS_CLASS
 305        depends on SPI
 306        help
 307          This option enables support for DAC124S085 SPI DAC from NatSemi,
 308          which can be used to control up to four LEDs.
 309
 310config LEDS_PWM
 311        tristate "PWM driven LED Support"
 312        depends on LEDS_CLASS
 313        depends on HAVE_PWM
 314        help
 315          This option enables support for pwm driven LEDs
 316
 317config LEDS_REGULATOR
 318        tristate "REGULATOR driven LED support"
 319        depends on LEDS_CLASS
 320        depends on REGULATOR
 321        help
 322          This option enables support for regulator driven LEDs.
 323
 324config LEDS_BD2802
 325        tristate "LED driver for BD2802 RGB LED"
 326        depends on LEDS_CLASS
 327        depends on I2C
 328        help
 329          This option enables support for BD2802GU RGB LED driver chips
 330          accessed via the I2C bus.
 331
 332config LEDS_INTEL_SS4200
 333        tristate "LED driver for Intel NAS SS4200 series"
 334        depends on LEDS_CLASS
 335        depends on PCI && DMI
 336        help
 337          This option enables support for the Intel SS4200 series of
 338          Network Attached Storage servers.  You may control the hard
 339          drive or power LEDs on the front panel.  Using this driver
 340          can stop the front LED from blinking after startup.
 341
 342config LEDS_LT3593
 343        tristate "LED driver for LT3593 controllers"
 344        depends on LEDS_CLASS
 345        depends on GENERIC_GPIO
 346        help
 347          This option enables support for LEDs driven by a Linear Technology
 348          LT3593 controller. This controller uses a special one-wire pulse
 349          coding protocol to set the brightness.
 350
 351config LEDS_ADP5520
 352        tristate "LED Support for ADP5520/ADP5501 PMIC"
 353        depends on LEDS_CLASS
 354        depends on PMIC_ADP5520
 355        help
 356          This option enables support for on-chip LED drivers found
 357          on Analog Devices ADP5520/ADP5501 PMICs.
 358
 359          To compile this driver as a module, choose M here: the module will
 360          be called leds-adp5520.
 361
 362config LEDS_DELL_NETBOOKS
 363        tristate "External LED on Dell Business Netbooks"
 364        depends on LEDS_CLASS
 365        depends on X86 && ACPI_WMI
 366        help
 367          This adds support for the Latitude 2100 and similar
 368          notebooks that have an external LED.
 369
 370config LEDS_MC13783
 371        tristate "LED Support for MC13783 PMIC"
 372        depends on LEDS_CLASS
 373        depends on MFD_MC13783
 374        help
 375          This option enable support for on-chip LED drivers found
 376          on Freescale Semiconductor MC13783 PMIC.
 377
 378config LEDS_NS2
 379        tristate "LED support for Network Space v2 GPIO LEDs"
 380        depends on LEDS_CLASS
 381        depends on MACH_NETSPACE_V2 || MACH_INETSPACE_V2 || \
 382                   MACH_NETSPACE_MAX_V2 || MACH_D2NET_V2 || \
 383                   MACH_NETSPACE_V2_DT || MACH_INETSPACE_V2_DT || \
 384                   MACH_NETSPACE_MAX_V2_DT || MACH_NETSPACE_MINI_V2_DT
 385        default y
 386        help
 387          This option enable support for the dual-GPIO LED found on the
 388          Network Space v2 board (and parents). This include Internet Space v2,
 389          Network Space (Max) v2 and d2 Network v2 boards.
 390
 391config LEDS_NETXBIG
 392        tristate "LED support for Big Network series LEDs"
 393        depends on MACH_NET2BIG_V2 || MACH_NET5BIG_V2
 394        depends on LEDS_CLASS
 395        default y
 396        help
 397          This option enable support for LEDs found on the LaCie 2Big
 398          and 5Big Network v2 boards. The LEDs are wired to a CPLD and are
 399          controlled through a GPIO extension bus.
 400
 401config LEDS_ASIC3
 402        bool "LED support for the HTC ASIC3"
 403        depends on LEDS_CLASS=y
 404        depends on MFD_ASIC3
 405        default y
 406        help
 407          This option enables support for the LEDs on the HTC ASIC3. The HTC
 408          ASIC3 LED GPIOs are inputs, not outputs, thus the leds-gpio driver
 409          cannot be used. This driver supports hardware blinking with an on+off
 410          period from 62ms to 125s. Say Y to enable LEDs on the HP iPAQ hx4700.
 411
 412config LEDS_RENESAS_TPU
 413        bool "LED support for Renesas TPU"
 414        depends on LEDS_CLASS=y && HAVE_CLK && GENERIC_GPIO
 415        help
 416          This option enables build of the LED TPU platform driver,
 417          suitable to drive any TPU channel on newer Renesas SoCs.
 418          The driver controls the GPIO pin connected to the LED via
 419          the GPIO framework and expects the LED to be connected to
 420          a pin that can be driven in both GPIO mode and using TPU
 421          pin function. The latter to support brightness control.
 422          Brightness control is supported but hardware blinking is not.
 423
 424config LEDS_TCA6507
 425        tristate "LED Support for TCA6507 I2C chip"
 426        depends on LEDS_CLASS && I2C
 427        help
 428          This option enables support for LEDs connected to TC6507
 429          LED driver chips accessed via the I2C bus.
 430          Driver support brightness control and hardware-assisted blinking.
 431
 432config LEDS_MAX8997
 433        tristate "LED support for MAX8997 PMIC"
 434        depends on LEDS_CLASS && MFD_MAX8997
 435        help
 436          This option enables support for on-chip LED drivers on
 437          MAXIM MAX8997 PMIC.
 438
 439config LEDS_LM355x
 440        tristate "LED support for LM355x Chips, LM3554 and LM3556"
 441        depends on LEDS_CLASS && I2C
 442        select REGMAP_I2C
 443        help
 444          This option enables support for LEDs connected to LM355x.
 445          LM355x includes Torch, Flash and Indicator functions.
 446
 447config LEDS_OT200
 448        tristate "LED support for the Bachmann OT200"
 449        depends on LEDS_CLASS && HAS_IOMEM
 450        help
 451          This option enables support for the LEDs on the Bachmann OT200.
 452          Say Y to enable LEDs on the Bachmann OT200.
 453
 454config LEDS_BLINKM
 455        tristate "LED support for the BlinkM I2C RGB LED"
 456        depends on LEDS_CLASS
 457        depends on I2C
 458        help
 459          This option enables support for the BlinkM RGB LED connected
 460          through I2C. Say Y to enable support for the BlinkM LED.
 461
 462config LEDS_TRIGGERS
 463        bool "LED Trigger support"
 464        depends on LEDS_CLASS
 465        help
 466          This option enables trigger support for the leds class.
 467          These triggers allow kernel events to drive the LEDs and can
 468          be configured via sysfs. If unsure, say Y.
 469
 470comment "LED Triggers"
 471
 472config LEDS_TRIGGER_TIMER
 473        tristate "LED Timer Trigger"
 474        depends on LEDS_TRIGGERS
 475        help
 476          This allows LEDs to be controlled by a programmable timer
 477          via sysfs. Some LED hardware can be programmed to start
 478          blinking the LED without any further software interaction.
 479          For more details read Documentation/leds/leds-class.txt.
 480
 481          If unsure, say Y.
 482
 483config LEDS_TRIGGER_ONESHOT
 484        tristate "LED One-shot Trigger"
 485        depends on LEDS_TRIGGERS
 486        help
 487          This allows LEDs to blink in one-shot pulses with parameters
 488          controlled via sysfs.  It's useful to notify the user on
 489          sporadic events, when there are no clear begin and end trap points,
 490          or on dense events, where this blinks the LED at constant rate if
 491          rearmed continuously.
 492
 493          It also shows how to use the led_blink_set_oneshot() function.
 494
 495          If unsure, say Y.
 496
 497config LEDS_TRIGGER_IDE_DISK
 498        bool "LED IDE Disk Trigger"
 499        depends on IDE_GD_ATA
 500        depends on LEDS_TRIGGERS
 501        help
 502          This allows LEDs to be controlled by IDE disk activity.
 503          If unsure, say Y.
 504
 505config LEDS_TRIGGER_HEARTBEAT
 506        tristate "LED Heartbeat Trigger"
 507        depends on LEDS_TRIGGERS
 508        help
 509          This allows LEDs to be controlled by a CPU load average.
 510          The flash frequency is a hyperbolic function of the 1-minute
 511          load average.
 512          If unsure, say Y.
 513
 514config LEDS_TRIGGER_BACKLIGHT
 515        tristate "LED backlight Trigger"
 516        depends on LEDS_TRIGGERS
 517        help
 518          This allows LEDs to be controlled as a backlight device: they
 519          turn off and on when the display is blanked and unblanked.
 520
 521          If unsure, say N.
 522
 523config LEDS_TRIGGER_CPU
 524        bool "LED CPU Trigger"
 525        depends on LEDS_TRIGGERS
 526        help
 527          This allows LEDs to be controlled by active CPUs. This shows
 528          the active CPUs across an array of LEDs so you can see which
 529          CPUs are active on the system at any given moment.
 530
 531          If unsure, say N.
 532
 533config LEDS_TRIGGER_GPIO
 534        tristate "LED GPIO Trigger"
 535        depends on LEDS_TRIGGERS
 536        depends on GPIOLIB
 537        help
 538          This allows LEDs to be controlled by gpio events. It's good
 539          when using gpios as switches and triggering the needed LEDs
 540          from there. One use case is n810's keypad LEDs that could
 541          be triggered by this trigger when user slides up to show
 542          keypad.
 543
 544          If unsure, say N.
 545
 546config LEDS_TRIGGER_DEFAULT_ON
 547        tristate "LED Default ON Trigger"
 548        depends on LEDS_TRIGGERS
 549        help
 550          This allows LEDs to be initialised in the ON state.
 551          If unsure, say Y.
 552
 553comment "iptables trigger is under Netfilter config (LED target)"
 554        depends on LEDS_TRIGGERS
 555
 556config LEDS_TRIGGER_TRANSIENT
 557        tristate "LED Transient Trigger"
 558        depends on LEDS_TRIGGERS
 559        help
 560          This allows one time activation of a transient state on
 561          GPIO/PWM based hardware.
 562          If unsure, say Y.
 563
 564endif # NEW_LEDS
 565
lxr.linux.no kindly hosted by Redpill Linpro AS, provider of Linux consulting and operations services since 1995.