linux/drivers/scsi/ncr53c8xx.h
<<
>>
Prefs
   1/******************************************************************************
   2**  Device driver for the PCI-SCSI NCR538XX controller family.
   3**
   4**  Copyright (C) 1994  Wolfgang Stanglmeier
   5**  Copyright (C) 1998-2001  Gerard Roudier <groudier@free.fr>
   6**
   7**  This program is free software; you can redistribute it and/or modify
   8**  it under the terms of the GNU General Public License as published by
   9**  the Free Software Foundation; either version 2 of the License, or
  10**  (at your option) any later version.
  11**
  12**  This program is distributed in the hope that it will be useful,
  13**  but WITHOUT ANY WARRANTY; without even the implied warranty of
  14**  MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
  15**  GNU General Public License for more details.
  16**
  17**  You should have received a copy of the GNU General Public License
  18**  along with this program; if not, write to the Free Software
  19**  Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
  20**
  21**-----------------------------------------------------------------------------
  22**
  23**  This driver has been ported to Linux from the FreeBSD NCR53C8XX driver
  24**  and is currently maintained by
  25**
  26**          Gerard Roudier              <groudier@free.fr>
  27**
  28**  Being given that this driver originates from the FreeBSD version, and
  29**  in order to keep synergy on both, any suggested enhancements and corrections
  30**  received on Linux are automatically a potential candidate for the FreeBSD 
  31**  version.
  32**
  33**  The original driver has been written for 386bsd and FreeBSD by
  34**          Wolfgang Stanglmeier        <wolf@cologne.de>
  35**          Stefan Esser                <se@mi.Uni-Koeln.de>
  36**
  37**  And has been ported to NetBSD by
  38**          Charles M. Hannum           <mycroft@gnu.ai.mit.edu>
  39**
  40**  NVRAM detection and reading.
  41**    Copyright (C) 1997 Richard Waltham <dormouse@farsrobt.demon.co.uk>
  42**
  43**  Added support for MIPS big endian systems.
  44**    Carsten Langgaard, carstenl@mips.com
  45**    Copyright (C) 2000 MIPS Technologies, Inc.  All rights reserved.
  46**
  47**  Added support for HP PARISC big endian systems.
  48**    Copyright (C) 2000 MIPS Technologies, Inc.  All rights reserved.
  49**
  50*******************************************************************************
  51*/
  52
  53#ifndef NCR53C8XX_H
  54#define NCR53C8XX_H
  55
  56#include <scsi/scsi_host.h>
  57
  58
  59/*
  60**      If you want a driver as small as possible, donnot define the 
  61**      following options.
  62*/
  63#define SCSI_NCR_BOOT_COMMAND_LINE_SUPPORT
  64#define SCSI_NCR_DEBUG_INFO_SUPPORT
  65
  66/*
  67**      To disable integrity checking, do not define the 
  68**      following option.
  69*/
  70#ifdef  CONFIG_SCSI_NCR53C8XX_INTEGRITY_CHECK
  71#       define SCSI_NCR_ENABLE_INTEGRITY_CHECK
  72#endif
  73
  74/* ---------------------------------------------------------------------
  75** Take into account kernel configured parameters.
  76** Most of these options can be overridden at startup by a command line.
  77** ---------------------------------------------------------------------
  78*/
  79
  80/*
  81 * For Ultra2 and Ultra3 SCSI support option, use special features. 
  82 *
  83 * Value (default) means:
  84 *      bit 0 : all features enabled, except:
  85 *              bit 1 : PCI Write And Invalidate.
  86 *              bit 2 : Data Phase Mismatch handling from SCRIPTS.
  87 *
  88 * Use boot options ncr53c8xx=specf:1 if you want all chip features to be 
  89 * enabled by the driver.
  90 */
  91#define SCSI_NCR_SETUP_SPECIAL_FEATURES         (3)
  92
  93#define SCSI_NCR_MAX_SYNC                       (80)
  94
  95/*
  96 * Allow tags from 2 to 256, default 8
  97 */
  98#ifdef  CONFIG_SCSI_NCR53C8XX_MAX_TAGS
  99#if     CONFIG_SCSI_NCR53C8XX_MAX_TAGS < 2
 100#define SCSI_NCR_MAX_TAGS       (2)
 101#elif   CONFIG_SCSI_NCR53C8XX_MAX_TAGS > 256
 102#define SCSI_NCR_MAX_TAGS       (256)
 103#else
 104#define SCSI_NCR_MAX_TAGS       CONFIG_SCSI_NCR53C8XX_MAX_TAGS
 105#endif
 106#else
 107#define SCSI_NCR_MAX_TAGS       (8)
 108#endif
 109
 110/*
 111 * Allow tagged command queuing support if configured with default number 
 112 * of tags set to max (see above).
 113 */
 114#ifdef  CONFIG_SCSI_NCR53C8XX_DEFAULT_TAGS
 115#define SCSI_NCR_SETUP_DEFAULT_TAGS     CONFIG_SCSI_NCR53C8XX_DEFAULT_TAGS
 116#elif   defined CONFIG_SCSI_NCR53C8XX_TAGGED_QUEUE
 117#define SCSI_NCR_SETUP_DEFAULT_TAGS     SCSI_NCR_MAX_TAGS
 118#else
 119#define SCSI_NCR_SETUP_DEFAULT_TAGS     (0)
 120#endif
 121
 122/*
 123 * Immediate arbitration
 124 */
 125#if defined(CONFIG_SCSI_NCR53C8XX_IARB)
 126#define SCSI_NCR_IARB_SUPPORT
 127#endif
 128
 129/*
 130 * Sync transfer frequency at startup.
 131 * Allow from 5Mhz to 80Mhz default 20 Mhz.
 132 */
 133#ifndef CONFIG_SCSI_NCR53C8XX_SYNC
 134#define CONFIG_SCSI_NCR53C8XX_SYNC      (20)
 135#elif   CONFIG_SCSI_NCR53C8XX_SYNC > SCSI_NCR_MAX_SYNC
 136#undef  CONFIG_SCSI_NCR53C8XX_SYNC
 137#define CONFIG_SCSI_NCR53C8XX_SYNC      SCSI_NCR_MAX_SYNC
 138#endif
 139
 140#if     CONFIG_SCSI_NCR53C8XX_SYNC == 0
 141#define SCSI_NCR_SETUP_DEFAULT_SYNC     (255)
 142#elif   CONFIG_SCSI_NCR53C8XX_SYNC <= 5
 143#define SCSI_NCR_SETUP_DEFAULT_SYNC     (50)
 144#elif   CONFIG_SCSI_NCR53C8XX_SYNC <= 20
 145#define SCSI_NCR_SETUP_DEFAULT_SYNC     (250/(CONFIG_SCSI_NCR53C8XX_SYNC))
 146#elif   CONFIG_SCSI_NCR53C8XX_SYNC <= 33
 147#define SCSI_NCR_SETUP_DEFAULT_SYNC     (11)
 148#elif   CONFIG_SCSI_NCR53C8XX_SYNC <= 40
 149#define SCSI_NCR_SETUP_DEFAULT_SYNC     (10)
 150#else
 151#define SCSI_NCR_SETUP_DEFAULT_SYNC     (9)
 152#endif
 153
 154/*
 155 * Disallow disconnections at boot-up
 156 */
 157#ifdef CONFIG_SCSI_NCR53C8XX_NO_DISCONNECT
 158#define SCSI_NCR_SETUP_DISCONNECTION    (0)
 159#else
 160#define SCSI_NCR_SETUP_DISCONNECTION    (1)
 161#endif
 162
 163/*
 164 * Force synchronous negotiation for all targets
 165 */
 166#ifdef CONFIG_SCSI_NCR53C8XX_FORCE_SYNC_NEGO
 167#define SCSI_NCR_SETUP_FORCE_SYNC_NEGO  (1)
 168#else
 169#define SCSI_NCR_SETUP_FORCE_SYNC_NEGO  (0)
 170#endif
 171
 172/*
 173 * Disable master parity checking (flawed hardwares need that)
 174 */
 175#ifdef CONFIG_SCSI_NCR53C8XX_DISABLE_MPARITY_CHECK
 176#define SCSI_NCR_SETUP_MASTER_PARITY    (0)
 177#else
 178#define SCSI_NCR_SETUP_MASTER_PARITY    (1)
 179#endif
 180
 181/*
 182 * Disable scsi parity checking (flawed devices may need that)
 183 */
 184#ifdef CONFIG_SCSI_NCR53C8XX_DISABLE_PARITY_CHECK
 185#define SCSI_NCR_SETUP_SCSI_PARITY      (0)
 186#else
 187#define SCSI_NCR_SETUP_SCSI_PARITY      (1)
 188#endif
 189
 190/*
 191 * Settle time after reset at boot-up
 192 */
 193#define SCSI_NCR_SETUP_SETTLE_TIME      (2)
 194
 195/*
 196**      Bridge quirks work-around option defaulted to 1.
 197*/
 198#ifndef SCSI_NCR_PCIQ_WORK_AROUND_OPT
 199#define SCSI_NCR_PCIQ_WORK_AROUND_OPT   1
 200#endif
 201
 202/*
 203**      Work-around common bridge misbehaviour.
 204**
 205**      - Do not flush posted writes in the opposite 
 206**        direction on read.
 207**      - May reorder DMA writes to memory.
 208**
 209**      This option should not affect performances 
 210**      significantly, so it is the default.
 211*/
 212#if     SCSI_NCR_PCIQ_WORK_AROUND_OPT == 1
 213#define SCSI_NCR_PCIQ_MAY_NOT_FLUSH_PW_UPSTREAM
 214#define SCSI_NCR_PCIQ_MAY_REORDER_WRITES
 215#define SCSI_NCR_PCIQ_MAY_MISS_COMPLETIONS
 216
 217/*
 218**      Same as option 1, but also deal with 
 219**      misconfigured interrupts.
 220**
 221**      - Edge triggered instead of level sensitive.
 222**      - No interrupt line connected.
 223**      - IRQ number misconfigured.
 224**      
 225**      If no interrupt is delivered, the driver will 
 226**      catch the interrupt conditions 10 times per 
 227**      second. No need to say that this option is 
 228**      not recommended.
 229*/
 230#elif   SCSI_NCR_PCIQ_WORK_AROUND_OPT == 2
 231#define SCSI_NCR_PCIQ_MAY_NOT_FLUSH_PW_UPSTREAM
 232#define SCSI_NCR_PCIQ_MAY_REORDER_WRITES
 233#define SCSI_NCR_PCIQ_MAY_MISS_COMPLETIONS
 234#define SCSI_NCR_PCIQ_BROKEN_INTR
 235
 236/*
 237**      Some bridge designers decided to flush 
 238**      everything prior to deliver the interrupt.
 239**      This option tries to deal with such a 
 240**      behaviour.
 241*/
 242#elif   SCSI_NCR_PCIQ_WORK_AROUND_OPT == 3
 243#define SCSI_NCR_PCIQ_SYNC_ON_INTR
 244#endif
 245
 246/*
 247**      Other parameters not configurable with "make config"
 248**      Avoid to change these constants, unless you know what you are doing.
 249*/
 250
 251#define SCSI_NCR_ALWAYS_SIMPLE_TAG
 252#define SCSI_NCR_MAX_SCATTER    (127)
 253#define SCSI_NCR_MAX_TARGET     (16)
 254
 255/*
 256**   Compute some desirable value for CAN_QUEUE 
 257**   and CMD_PER_LUN.
 258**   The driver will use lower values if these 
 259**   ones appear to be too large.
 260*/
 261#define SCSI_NCR_CAN_QUEUE      (8*SCSI_NCR_MAX_TAGS + 2*SCSI_NCR_MAX_TARGET)
 262#define SCSI_NCR_CMD_PER_LUN    (SCSI_NCR_MAX_TAGS)
 263
 264#define SCSI_NCR_SG_TABLESIZE   (SCSI_NCR_MAX_SCATTER)
 265#define SCSI_NCR_TIMER_INTERVAL (HZ)
 266
 267#if 1 /* defined CONFIG_SCSI_MULTI_LUN */
 268#define SCSI_NCR_MAX_LUN        (16)
 269#else
 270#define SCSI_NCR_MAX_LUN        (1)
 271#endif
 272
 273/*
 274 *  IO functions definition for big/little endian CPU support.
 275 *  For now, the NCR is only supported in little endian addressing mode, 
 276 */
 277
 278#ifdef  __BIG_ENDIAN
 279
 280#define inw_l2b         inw
 281#define inl_l2b         inl
 282#define outw_b2l        outw
 283#define outl_b2l        outl
 284
 285#define readb_raw       readb
 286#define writeb_raw      writeb
 287
 288#if defined(SCSI_NCR_BIG_ENDIAN)
 289#define readw_l2b       __raw_readw
 290#define readl_l2b       __raw_readl
 291#define writew_b2l      __raw_writew
 292#define writel_b2l      __raw_writel
 293#define readw_raw       __raw_readw
 294#define readl_raw       __raw_readl
 295#define writew_raw      __raw_writew
 296#define writel_raw      __raw_writel
 297#else   /* Other big-endian */
 298#define readw_l2b       readw
 299#define readl_l2b       readl
 300#define writew_b2l      writew
 301#define writel_b2l      writel
 302#define readw_raw       readw
 303#define readl_raw       readl
 304#define writew_raw      writew
 305#define writel_raw      writel
 306#endif
 307
 308#else   /* little endian */
 309
 310#define inw_raw         inw
 311#define inl_raw         inl
 312#define outw_raw        outw
 313#define outl_raw        outl
 314
 315#define readb_raw       readb
 316#define readw_raw       readw
 317#define readl_raw       readl
 318#define writeb_raw      writeb
 319#define writew_raw      writew
 320#define writel_raw      writel
 321
 322#endif
 323
 324#if !defined(__hppa__) && !defined(__mips__)
 325#ifdef  SCSI_NCR_BIG_ENDIAN
 326#error  "The NCR in BIG ENDIAN addressing mode is not (yet) supported"
 327#endif
 328#endif
 329
 330#define MEMORY_BARRIER()        mb()
 331
 332
 333/*
 334 *  If the NCR uses big endian addressing mode over the 
 335 *  PCI, actual io register addresses for byte and word 
 336 *  accesses must be changed according to lane routing.
 337 *  Btw, ncr_offb() and ncr_offw() macros only apply to 
 338 *  constants and so donnot generate bloated code.
 339 */
 340
 341#if     defined(SCSI_NCR_BIG_ENDIAN)
 342
 343#define ncr_offb(o)     (((o)&~3)+((~((o)&3))&3))
 344#define ncr_offw(o)     (((o)&~3)+((~((o)&3))&2))
 345
 346#else
 347
 348#define ncr_offb(o)     (o)
 349#define ncr_offw(o)     (o)
 350
 351#endif
 352
 353/*
 354 *  If the CPU and the NCR use same endian-ness addressing,
 355 *  no byte reordering is needed for script patching.
 356 *  Macro cpu_to_scr() is to be used for script patching.
 357 *  Macro scr_to_cpu() is to be used for getting a DWORD 
 358 *  from the script.
 359 */
 360
 361#if     defined(__BIG_ENDIAN) && !defined(SCSI_NCR_BIG_ENDIAN)
 362
 363#define cpu_to_scr(dw)  cpu_to_le32(dw)
 364#define scr_to_cpu(dw)  le32_to_cpu(dw)
 365
 366#elif   defined(__LITTLE_ENDIAN) && defined(SCSI_NCR_BIG_ENDIAN)
 367
 368#define cpu_to_scr(dw)  cpu_to_be32(dw)
 369#define scr_to_cpu(dw)  be32_to_cpu(dw)
 370
 371#else
 372
 373#define cpu_to_scr(dw)  (dw)
 374#define scr_to_cpu(dw)  (dw)
 375
 376#endif
 377
 378/*
 379 *  Access to the controller chip.
 380 *
 381 *  If the CPU and the NCR use same endian-ness addressing,
 382 *  no byte reordering is needed for accessing chip io 
 383 *  registers. Functions suffixed by '_raw' are assumed 
 384 *  to access the chip over the PCI without doing byte 
 385 *  reordering. Functions suffixed by '_l2b' are 
 386 *  assumed to perform little-endian to big-endian byte 
 387 *  reordering, those suffixed by '_b2l' blah, blah,
 388 *  blah, ...
 389 */
 390
 391/*
 392 *  MEMORY mapped IO input / output
 393 */
 394
 395#define INB_OFF(o)              readb_raw((char __iomem *)np->reg + ncr_offb(o))
 396#define OUTB_OFF(o, val)        writeb_raw((val), (char __iomem *)np->reg + ncr_offb(o))
 397
 398#if     defined(__BIG_ENDIAN) && !defined(SCSI_NCR_BIG_ENDIAN)
 399
 400#define INW_OFF(o)              readw_l2b((char __iomem *)np->reg + ncr_offw(o))
 401#define INL_OFF(o)              readl_l2b((char __iomem *)np->reg + (o))
 402
 403#define OUTW_OFF(o, val)        writew_b2l((val), (char __iomem *)np->reg + ncr_offw(o))
 404#define OUTL_OFF(o, val)        writel_b2l((val), (char __iomem *)np->reg + (o))
 405
 406#elif   defined(__LITTLE_ENDIAN) && defined(SCSI_NCR_BIG_ENDIAN)
 407
 408#define INW_OFF(o)              readw_b2l((char __iomem *)np->reg + ncr_offw(o))
 409#define INL_OFF(o)              readl_b2l((char __iomem *)np->reg + (o))
 410
 411#define OUTW_OFF(o, val)        writew_l2b((val), (char __iomem *)np->reg + ncr_offw(o))
 412#define OUTL_OFF(o, val)        writel_l2b((val), (char __iomem *)np->reg + (o))
 413
 414#else
 415
 416#ifdef CONFIG_SCSI_NCR53C8XX_NO_WORD_TRANSFERS
 417/* Only 8 or 32 bit transfers allowed */
 418#define INW_OFF(o)              (readb((char __iomem *)np->reg + ncr_offw(o)) << 8 | readb((char __iomem *)np->reg + ncr_offw(o) + 1))
 419#else
 420#define INW_OFF(o)              readw_raw((char __iomem *)np->reg + ncr_offw(o))
 421#endif
 422#define INL_OFF(o)              readl_raw((char __iomem *)np->reg + (o))
 423
 424#ifdef CONFIG_SCSI_NCR53C8XX_NO_WORD_TRANSFERS
 425/* Only 8 or 32 bit transfers allowed */
 426#define OUTW_OFF(o, val)        do { writeb((char)((val) >> 8), (char __iomem *)np->reg + ncr_offw(o)); writeb((char)(val), (char __iomem *)np->reg + ncr_offw(o) + 1); } while (0)
 427#else
 428#define OUTW_OFF(o, val)        writew_raw((val), (char __iomem *)np->reg + ncr_offw(o))
 429#endif
 430#define OUTL_OFF(o, val)        writel_raw((val), (char __iomem *)np->reg + (o))
 431
 432#endif
 433
 434#define INB(r)          INB_OFF (offsetof(struct ncr_reg,r))
 435#define INW(r)          INW_OFF (offsetof(struct ncr_reg,r))
 436#define INL(r)          INL_OFF (offsetof(struct ncr_reg,r))
 437
 438#define OUTB(r, val)    OUTB_OFF (offsetof(struct ncr_reg,r), (val))
 439#define OUTW(r, val)    OUTW_OFF (offsetof(struct ncr_reg,r), (val))
 440#define OUTL(r, val)    OUTL_OFF (offsetof(struct ncr_reg,r), (val))
 441
 442/*
 443 *  Set bit field ON, OFF 
 444 */
 445
 446#define OUTONB(r, m)    OUTB(r, INB(r) | (m))
 447#define OUTOFFB(r, m)   OUTB(r, INB(r) & ~(m))
 448#define OUTONW(r, m)    OUTW(r, INW(r) | (m))
 449#define OUTOFFW(r, m)   OUTW(r, INW(r) & ~(m))
 450#define OUTONL(r, m)    OUTL(r, INL(r) | (m))
 451#define OUTOFFL(r, m)   OUTL(r, INL(r) & ~(m))
 452
 453/*
 454 *  We normally want the chip to have a consistent view
 455 *  of driver internal data structures when we restart it.
 456 *  Thus these macros.
 457 */
 458#define OUTL_DSP(v)                             \
 459        do {                                    \
 460                MEMORY_BARRIER();               \
 461                OUTL (nc_dsp, (v));             \
 462        } while (0)
 463
 464#define OUTONB_STD()                            \
 465        do {                                    \
 466                MEMORY_BARRIER();               \
 467                OUTONB (nc_dcntl, (STD|NOCOM)); \
 468        } while (0)
 469
 470
 471/*
 472**   NCR53C8XX devices features table.
 473*/
 474struct ncr_chip {
 475        unsigned short  revision_id;
 476        unsigned char   burst_max;      /* log-base-2 of max burst */
 477        unsigned char   offset_max;
 478        unsigned char   nr_divisor;
 479        unsigned int    features;
 480#define FE_LED0         (1<<0)
 481#define FE_WIDE         (1<<1)    /* Wide data transfers */
 482#define FE_ULTRA        (1<<2)    /* Ultra speed 20Mtrans/sec */
 483#define FE_DBLR         (1<<4)    /* Clock doubler present */
 484#define FE_QUAD         (1<<5)    /* Clock quadrupler present */
 485#define FE_ERL          (1<<6)    /* Enable read line */
 486#define FE_CLSE         (1<<7)    /* Cache line size enable */
 487#define FE_WRIE         (1<<8)    /* Write & Invalidate enable */
 488#define FE_ERMP         (1<<9)    /* Enable read multiple */
 489#define FE_BOF          (1<<10)   /* Burst opcode fetch */
 490#define FE_DFS          (1<<11)   /* DMA fifo size */
 491#define FE_PFEN         (1<<12)   /* Prefetch enable */
 492#define FE_LDSTR        (1<<13)   /* Load/Store supported */
 493#define FE_RAM          (1<<14)   /* On chip RAM present */
 494#define FE_VARCLK       (1<<15)   /* SCSI clock may vary */
 495#define FE_RAM8K        (1<<16)   /* On chip RAM sized 8Kb */
 496#define FE_64BIT        (1<<17)   /* Have a 64-bit PCI interface */
 497#define FE_IO256        (1<<18)   /* Requires full 256 bytes in PCI space */
 498#define FE_NOPM         (1<<19)   /* Scripts handles phase mismatch */
 499#define FE_LEDC         (1<<20)   /* Hardware control of LED */
 500#define FE_DIFF         (1<<21)   /* Support Differential SCSI */
 501#define FE_66MHZ        (1<<23)   /* 66MHz PCI Support */
 502#define FE_DAC          (1<<24)   /* Support DAC cycles (64 bit addressing) */
 503#define FE_ISTAT1       (1<<25)   /* Have ISTAT1, MBOX0, MBOX1 registers */
 504#define FE_DAC_IN_USE   (1<<26)   /* Platform does DAC cycles */
 505#define FE_EHP          (1<<27)   /* 720: Even host parity */
 506#define FE_MUX          (1<<28)   /* 720: Multiplexed bus */
 507#define FE_EA           (1<<29)   /* 720: Enable Ack */
 508
 509#define FE_CACHE_SET    (FE_ERL|FE_CLSE|FE_WRIE|FE_ERMP)
 510#define FE_SCSI_SET     (FE_WIDE|FE_ULTRA|FE_DBLR|FE_QUAD|F_CLK80)
 511#define FE_SPECIAL_SET  (FE_CACHE_SET|FE_BOF|FE_DFS|FE_LDSTR|FE_PFEN|FE_RAM)
 512};
 513
 514
 515/*
 516**      Driver setup structure.
 517**
 518**      This structure is initialized from linux config options.
 519**      It can be overridden at boot-up by the boot command line.
 520*/
 521#define SCSI_NCR_MAX_EXCLUDES 8
 522struct ncr_driver_setup {
 523        u8      master_parity;
 524        u8      scsi_parity;
 525        u8      disconnection;
 526        u8      special_features;
 527        u8      force_sync_nego;
 528        u8      reverse_probe;
 529        u8      pci_fix_up;
 530        u8      use_nvram;
 531        u8      verbose;
 532        u8      default_tags;
 533        u16     default_sync;
 534        u16     debug;
 535        u8      burst_max;
 536        u8      led_pin;
 537        u8      max_wide;
 538        u8      settle_delay;
 539        u8      diff_support;
 540        u8      irqm;
 541        u8      bus_check;
 542        u8      optimize;
 543        u8      recovery;
 544        u8      host_id;
 545        u16     iarb;
 546        u32     excludes[SCSI_NCR_MAX_EXCLUDES];
 547        char    tag_ctrl[100];
 548};
 549
 550/*
 551**      Initial setup.
 552**      Can be overridden at startup by a command line.
 553*/
 554#define SCSI_NCR_DRIVER_SETUP                   \
 555{                                               \
 556        SCSI_NCR_SETUP_MASTER_PARITY,           \
 557        SCSI_NCR_SETUP_SCSI_PARITY,             \
 558        SCSI_NCR_SETUP_DISCONNECTION,           \
 559        SCSI_NCR_SETUP_SPECIAL_FEATURES,        \
 560        SCSI_NCR_SETUP_FORCE_SYNC_NEGO,         \
 561        0,                                      \
 562        0,                                      \
 563        1,                                      \
 564        0,                                      \
 565        SCSI_NCR_SETUP_DEFAULT_TAGS,            \
 566        SCSI_NCR_SETUP_DEFAULT_SYNC,            \
 567        0x00,                                   \
 568        7,                                      \
 569        0,                                      \
 570        1,                                      \
 571        SCSI_NCR_SETUP_SETTLE_TIME,             \
 572        0,                                      \
 573        0,                                      \
 574        1,                                      \
 575        0,                                      \
 576        0,                                      \
 577        255,                                    \
 578        0x00                                    \
 579}
 580
 581/*
 582**      Boot fail safe setup.
 583**      Override initial setup from boot command line:
 584**      ncr53c8xx=safe:y
 585*/
 586#define SCSI_NCR_DRIVER_SAFE_SETUP              \
 587{                                               \
 588        0,                                      \
 589        1,                                      \
 590        0,                                      \
 591        0,                                      \
 592        0,                                      \
 593        0,                                      \
 594        0,                                      \
 595        1,                                      \
 596        2,                                      \
 597        0,                                      \
 598        255,                                    \
 599        0x00,                                   \
 600        255,                                    \
 601        0,                                      \
 602        0,                                      \
 603        10,                                     \
 604        1,                                      \
 605        1,                                      \
 606        1,                                      \
 607        0,                                      \
 608        0,                                      \
 609        255                                     \
 610}
 611
 612/**************** ORIGINAL CONTENT of ncrreg.h from FreeBSD ******************/
 613
 614/*-----------------------------------------------------------------
 615**
 616**      The ncr 53c810 register structure.
 617**
 618**-----------------------------------------------------------------
 619*/
 620
 621struct ncr_reg {
 622/*00*/  u8      nc_scntl0;    /* full arb., ena parity, par->ATN  */
 623
 624/*01*/  u8      nc_scntl1;    /* no reset                         */
 625        #define   ISCON   0x10  /* connected to scsi                */
 626        #define   CRST    0x08  /* force reset                      */
 627        #define   IARB    0x02  /* immediate arbitration            */
 628
 629/*02*/  u8      nc_scntl2;    /* no disconnect expected           */
 630        #define   SDU     0x80  /* cmd: disconnect will raise error */
 631        #define   CHM     0x40  /* sta: chained mode                */
 632        #define   WSS     0x08  /* sta: wide scsi send           [W]*/
 633        #define   WSR     0x01  /* sta: wide scsi received       [W]*/
 634
 635/*03*/  u8      nc_scntl3;    /* cnf system clock dependent       */
 636        #define   EWS     0x08  /* cmd: enable wide scsi         [W]*/
 637        #define   ULTRA   0x80  /* cmd: ULTRA enable                */
 638                                /* bits 0-2, 7 rsvd for C1010       */
 639
 640/*04*/  u8      nc_scid;        /* cnf host adapter scsi address    */
 641        #define   RRE     0x40  /* r/w:e enable response to resel.  */
 642        #define   SRE     0x20  /* r/w:e enable response to select  */
 643
 644/*05*/  u8      nc_sxfer;       /* ### Sync speed and count         */
 645                                /* bits 6-7 rsvd for C1010          */
 646
 647/*06*/  u8      nc_sdid;        /* ### Destination-ID               */
 648
 649/*07*/  u8      nc_gpreg;       /* ??? IO-Pins                      */
 650
 651/*08*/  u8      nc_sfbr;        /* ### First byte in phase          */
 652
 653/*09*/  u8      nc_socl;
 654        #define   CREQ    0x80  /* r/w: SCSI-REQ                    */
 655        #define   CACK    0x40  /* r/w: SCSI-ACK                    */
 656        #define   CBSY    0x20  /* r/w: SCSI-BSY                    */
 657        #define   CSEL    0x10  /* r/w: SCSI-SEL                    */
 658        #define   CATN    0x08  /* r/w: SCSI-ATN                    */
 659        #define   CMSG    0x04  /* r/w: SCSI-MSG                    */
 660        #define   CC_D    0x02  /* r/w: SCSI-C_D                    */
 661        #define   CI_O    0x01  /* r/w: SCSI-I_O                    */
 662
 663/*0a*/  u8      nc_ssid;
 664
 665/*0b*/  u8      nc_sbcl;
 666
 667/*0c*/  u8      nc_dstat;
 668        #define   DFE     0x80  /* sta: dma fifo empty              */
 669        #define   MDPE    0x40  /* int: master data parity error    */
 670        #define   BF      0x20  /* int: script: bus fault           */
 671        #define   ABRT    0x10  /* int: script: command aborted     */
 672        #define   SSI     0x08  /* int: script: single step         */
 673        #define   SIR     0x04  /* int: script: interrupt instruct. */
 674        #define   IID     0x01  /* int: script: illegal instruct.   */
 675
 676/*0d*/  u8      nc_sstat0;
 677        #define   ILF     0x80  /* sta: data in SIDL register lsb   */
 678        #define   ORF     0x40  /* sta: data in SODR register lsb   */
 679        #define   OLF     0x20  /* sta: data in SODL register lsb   */
 680        #define   AIP     0x10  /* sta: arbitration in progress     */
 681        #define   LOA     0x08  /* sta: arbitration lost            */
 682        #define   WOA     0x04  /* sta: arbitration won             */
 683        #define   IRST    0x02  /* sta: scsi reset signal           */
 684        #define   SDP     0x01  /* sta: scsi parity signal          */
 685
 686/*0e*/  u8      nc_sstat1;
 687        #define   FF3210  0xf0  /* sta: bytes in the scsi fifo      */
 688
 689/*0f*/  u8      nc_sstat2;
 690        #define   ILF1    0x80  /* sta: data in SIDL register msb[W]*/
 691        #define   ORF1    0x40  /* sta: data in SODR register msb[W]*/
 692        #define   OLF1    0x20  /* sta: data in SODL register msb[W]*/
 693        #define   DM      0x04  /* sta: DIFFSENS mismatch (895/6 only) */
 694        #define   LDSC    0x02  /* sta: disconnect & reconnect      */
 695
 696/*10*/  u8      nc_dsa; /* --> Base page                    */
 697/*11*/  u8      nc_dsa1;
 698/*12*/  u8      nc_dsa2;
 699/*13*/  u8      nc_dsa3;
 700
 701/*14*/  u8      nc_istat;       /* --> Main Command and status      */
 702        #define   CABRT   0x80  /* cmd: abort current operation     */
 703        #define   SRST    0x40  /* mod: reset chip                  */
 704        #define   SIGP    0x20  /* r/w: message from host to ncr    */
 705        #define   SEM     0x10  /* r/w: message between host + ncr  */
 706        #define   CON     0x08  /* sta: connected to scsi           */
 707        #define   INTF    0x04  /* sta: int on the fly (reset by wr)*/
 708        #define   SIP     0x02  /* sta: scsi-interrupt              */
 709        #define   DIP     0x01  /* sta: host/script interrupt       */
 710
 711/*15*/  u8      nc_istat1;      /* 896 and later cores only */
 712        #define   FLSH    0x04  /* sta: chip is flushing            */
 713        #define   SRUN    0x02  /* sta: scripts are running         */
 714        #define   SIRQD   0x01  /* r/w: disable INT pin             */
 715
 716/*16*/  u8      nc_mbox0;       /* 896 and later cores only */
 717/*17*/  u8      nc_mbox1;       /* 896 and later cores only */
 718
 719/*18*/  u8      nc_ctest0;
 720        #define   EHP     0x04  /* 720 even host parity             */
 721/*19*/  u8      nc_ctest1;
 722
 723/*1a*/  u8      nc_ctest2;
 724        #define   CSIGP   0x40
 725                                /* bits 0-2,7 rsvd for C1010        */
 726
 727/*1b*/  u8      nc_ctest3;
 728        #define   FLF     0x08  /* cmd: flush dma fifo              */
 729        #define   CLF     0x04  /* cmd: clear dma fifo              */
 730        #define   FM      0x02  /* mod: fetch pin mode              */
 731        #define   WRIE    0x01  /* mod: write and invalidate enable */
 732                                /* bits 4-7 rsvd for C1010          */
 733
 734/*1c*/  u32    nc_temp; /* ### Temporary stack              */
 735
 736/*20*/  u8      nc_dfifo;
 737/*21*/  u8      nc_ctest4;
 738        #define   MUX     0x80  /* 720 host bus multiplex mode      */
 739        #define   BDIS    0x80  /* mod: burst disable               */
 740        #define   MPEE    0x08  /* mod: master parity error enable  */
 741
 742/*22*/  u8      nc_ctest5;
 743        #define   DFS     0x20  /* mod: dma fifo size               */
 744                                /* bits 0-1, 3-7 rsvd for C1010          */
 745/*23*/  u8      nc_ctest6;
 746
 747/*24*/  u32    nc_dbc;  /* ### Byte count and command       */
 748/*28*/  u32    nc_dnad; /* ### Next command register        */
 749/*2c*/  u32    nc_dsp;  /* --> Script Pointer               */
 750/*30*/  u32    nc_dsps; /* --> Script pointer save/opcode#2 */
 751
 752/*34*/  u8      nc_scratcha;  /* Temporary register a            */
 753/*35*/  u8      nc_scratcha1;
 754/*36*/  u8      nc_scratcha2;
 755/*37*/  u8      nc_scratcha3;
 756
 757/*38*/  u8      nc_dmode;
 758        #define   BL_2    0x80  /* mod: burst length shift value +2 */
 759        #define   BL_1    0x40  /* mod: burst length shift value +1 */
 760        #define   ERL     0x08  /* mod: enable read line            */
 761        #define   ERMP    0x04  /* mod: enable read multiple        */
 762        #define   BOF     0x02  /* mod: burst op code fetch         */
 763
 764/*39*/  u8      nc_dien;
 765/*3a*/  u8      nc_sbr;
 766
 767/*3b*/  u8      nc_dcntl;       /* --> Script execution control     */
 768        #define   CLSE    0x80  /* mod: cache line size enable      */
 769        #define   PFF     0x40  /* cmd: pre-fetch flush             */
 770        #define   PFEN    0x20  /* mod: pre-fetch enable            */
 771        #define   EA      0x20  /* mod: 720 enable-ack              */
 772        #define   SSM     0x10  /* mod: single step mode            */
 773        #define   IRQM    0x08  /* mod: irq mode (1 = totem pole !) */
 774        #define   STD     0x04  /* cmd: start dma mode              */
 775        #define   IRQD    0x02  /* mod: irq disable                 */
 776        #define   NOCOM   0x01  /* cmd: protect sfbr while reselect */
 777                                /* bits 0-1 rsvd for C1010          */
 778
 779/*3c*/  u32     nc_adder;
 780
 781/*40*/  u16     nc_sien;        /* -->: interrupt enable            */
 782/*42*/  u16     nc_sist;        /* <--: interrupt status            */
 783        #define   SBMC    0x1000/* sta: SCSI Bus Mode Change (895/6 only) */
 784        #define   STO     0x0400/* sta: timeout (select)            */
 785        #define   GEN     0x0200/* sta: timeout (general)           */
 786        #define   HTH     0x0100/* sta: timeout (handshake)         */
 787        #define   MA      0x80  /* sta: phase mismatch              */
 788        #define   CMP     0x40  /* sta: arbitration complete        */
 789        #define   SEL     0x20  /* sta: selected by another device  */
 790        #define   RSL     0x10  /* sta: reselected by another device*/
 791        #define   SGE     0x08  /* sta: gross error (over/underflow)*/
 792        #define   UDC     0x04  /* sta: unexpected disconnect       */
 793        #define   RST     0x02  /* sta: scsi bus reset detected     */
 794        #define   PAR     0x01  /* sta: scsi parity error           */
 795
 796/*44*/  u8      nc_slpar;
 797/*45*/  u8      nc_swide;
 798/*46*/  u8      nc_macntl;
 799/*47*/  u8      nc_gpcntl;
 800/*48*/  u8      nc_stime0;    /* cmd: timeout for select&handshake*/
 801/*49*/  u8      nc_stime1;    /* cmd: timeout user defined        */
 802/*4a*/  u16   nc_respid;    /* sta: Reselect-IDs                */
 803
 804/*4c*/  u8      nc_stest0;
 805
 806/*4d*/  u8      nc_stest1;
 807        #define   SCLK    0x80  /* Use the PCI clock as SCSI clock      */
 808        #define   DBLEN   0x08  /* clock doubler running                */
 809        #define   DBLSEL  0x04  /* clock doubler selected               */
 810  
 811
 812/*4e*/  u8      nc_stest2;
 813        #define   ROF     0x40  /* reset scsi offset (after gross error!) */
 814        #define   DIF     0x20  /* 720 SCSI differential mode             */
 815        #define   EXT     0x02  /* extended filtering                     */
 816
 817/*4f*/  u8      nc_stest3;
 818        #define   TE     0x80   /* c: tolerAnt enable */
 819        #define   HSC    0x20   /* c: Halt SCSI Clock */
 820        #define   CSF    0x02   /* c: clear scsi fifo */
 821
 822/*50*/  u16   nc_sidl;  /* Lowlevel: latched from scsi data */
 823/*52*/  u8      nc_stest4;
 824        #define   SMODE  0xc0   /* SCSI bus mode      (895/6 only) */
 825        #define    SMODE_HVD 0x40       /* High Voltage Differential       */
 826        #define    SMODE_SE  0x80       /* Single Ended                    */
 827        #define    SMODE_LVD 0xc0       /* Low Voltage Differential        */
 828        #define   LCKFRQ 0x20   /* Frequency Lock (895/6 only)     */
 829                                /* bits 0-5 rsvd for C1010          */
 830
 831/*53*/  u8      nc_53_;
 832/*54*/  u16     nc_sodl;        /* Lowlevel: data out to scsi data  */
 833/*56*/  u8      nc_ccntl0;      /* Chip Control 0 (896)             */
 834        #define   ENPMJ  0x80   /* Enable Phase Mismatch Jump       */
 835        #define   PMJCTL 0x40   /* Phase Mismatch Jump Control      */
 836        #define   ENNDJ  0x20   /* Enable Non Data PM Jump          */
 837        #define   DISFC  0x10   /* Disable Auto FIFO Clear          */
 838        #define   DILS   0x02   /* Disable Internal Load/Store      */
 839        #define   DPR    0x01   /* Disable Pipe Req                 */
 840
 841/*57*/  u8      nc_ccntl1;      /* Chip Control 1 (896)             */
 842        #define   ZMOD   0x80   /* High Impedance Mode              */
 843        #define   DIC    0x10   /* Disable Internal Cycles          */
 844        #define   DDAC   0x08   /* Disable Dual Address Cycle       */
 845        #define   XTIMOD 0x04   /* 64-bit Table Ind. Indexing Mode  */
 846        #define   EXTIBMV 0x02  /* Enable 64-bit Table Ind. BMOV    */
 847        #define   EXDBMV 0x01   /* Enable 64-bit Direct BMOV        */
 848
 849/*58*/  u16     nc_sbdl;        /* Lowlevel: data from scsi data    */
 850/*5a*/  u16     nc_5a_;
 851
 852/*5c*/  u8      nc_scr0;        /* Working register B               */
 853/*5d*/  u8      nc_scr1;        /*                                  */
 854/*5e*/  u8      nc_scr2;        /*                                  */
 855/*5f*/  u8      nc_scr3;        /*                                  */
 856
 857/*60*/  u8      nc_scrx[64];    /* Working register C-R             */
 858/*a0*/  u32     nc_mmrs;        /* Memory Move Read Selector        */
 859/*a4*/  u32     nc_mmws;        /* Memory Move Write Selector       */
 860/*a8*/  u32     nc_sfs;         /* Script Fetch Selector            */
 861/*ac*/  u32     nc_drs;         /* DSA Relative Selector            */
 862/*b0*/  u32     nc_sbms;        /* Static Block Move Selector       */
 863/*b4*/  u32     nc_dbms;        /* Dynamic Block Move Selector      */
 864/*b8*/  u32     nc_dnad64;      /* DMA Next Address 64              */
 865/*bc*/  u16     nc_scntl4;      /* C1010 only                       */
 866        #define   U3EN   0x80   /* Enable Ultra 3                   */
 867        #define   AIPEN  0x40   /* Allow check upper byte lanes     */
 868        #define   XCLKH_DT 0x08 /* Extra clock of data hold on DT
 869                                        transfer edge               */
 870        #define   XCLKH_ST 0x04 /* Extra clock of data hold on ST
 871                                        transfer edge               */
 872
 873/*be*/  u8      nc_aipcntl0;    /* Epat Control 1 C1010 only        */
 874/*bf*/  u8      nc_aipcntl1;    /* AIP Control C1010_66 Only        */
 875
 876/*c0*/  u32     nc_pmjad1;      /* Phase Mismatch Jump Address 1    */
 877/*c4*/  u32     nc_pmjad2;      /* Phase Mismatch Jump Address 2    */
 878/*c8*/  u8      nc_rbc;         /* Remaining Byte Count             */
 879/*c9*/  u8      nc_rbc1;        /*                                  */
 880/*ca*/  u8      nc_rbc2;        /*                                  */
 881/*cb*/  u8      nc_rbc3;        /*                                  */
 882
 883/*cc*/  u8      nc_ua;          /* Updated Address                  */
 884/*cd*/  u8      nc_ua1;         /*                                  */
 885/*ce*/  u8      nc_ua2;         /*                                  */
 886/*cf*/  u8      nc_ua3;         /*                                  */
 887/*d0*/  u32     nc_esa;         /* Entry Storage Address            */
 888/*d4*/  u8      nc_ia;          /* Instruction Address              */
 889/*d5*/  u8      nc_ia1;
 890/*d6*/  u8      nc_ia2;
 891/*d7*/  u8      nc_ia3;
 892/*d8*/  u32     nc_sbc;         /* SCSI Byte Count (3 bytes only)   */
 893/*dc*/  u32     nc_csbc;        /* Cumulative SCSI Byte Count       */
 894
 895                                /* Following for C1010 only         */
 896/*e0*/  u16     nc_crcpad;      /* CRC Value                        */
 897/*e2*/  u8      nc_crccntl0;    /* CRC control register             */
 898        #define   SNDCRC  0x10  /* Send CRC Request                 */
 899/*e3*/  u8      nc_crccntl1;    /* CRC control register             */
 900/*e4*/  u32     nc_crcdata;     /* CRC data register                */ 
 901/*e8*/  u32     nc_e8_;         /* rsvd                             */
 902/*ec*/  u32     nc_ec_;         /* rsvd                             */
 903/*f0*/  u16     nc_dfbc;        /* DMA FIFO byte count              */ 
 904
 905};
 906
 907/*-----------------------------------------------------------
 908**
 909**      Utility macros for the script.
 910**
 911**-----------------------------------------------------------
 912*/
 913
 914#define REGJ(p,r) (offsetof(struct ncr_reg, p ## r))
 915#define REG(r) REGJ (nc_, r)
 916
 917typedef u32 ncrcmd;
 918
 919/*-----------------------------------------------------------
 920**
 921**      SCSI phases
 922**
 923**      DT phases illegal for ncr driver.
 924**
 925**-----------------------------------------------------------
 926*/
 927
 928#define SCR_DATA_OUT    0x00000000
 929#define SCR_DATA_IN     0x01000000
 930#define SCR_COMMAND     0x02000000
 931#define SCR_STATUS      0x03000000
 932#define SCR_DT_DATA_OUT 0x04000000
 933#define SCR_DT_DATA_IN  0x05000000
 934#define SCR_MSG_OUT     0x06000000
 935#define SCR_MSG_IN      0x07000000
 936
 937#define SCR_ILG_OUT     0x04000000
 938#define SCR_ILG_IN      0x05000000
 939
 940/*-----------------------------------------------------------
 941**
 942**      Data transfer via SCSI.
 943**
 944**-----------------------------------------------------------
 945**
 946**      MOVE_ABS (LEN)
 947**      <<start address>>
 948**
 949**      MOVE_IND (LEN)
 950**      <<dnad_offset>>
 951**
 952**      MOVE_TBL
 953**      <<dnad_offset>>
 954**
 955**-----------------------------------------------------------
 956*/
 957
 958#define OPC_MOVE          0x08000000
 959
 960#define SCR_MOVE_ABS(l) ((0x00000000 | OPC_MOVE) | (l))
 961#define SCR_MOVE_IND(l) ((0x20000000 | OPC_MOVE) | (l))
 962#define SCR_MOVE_TBL     (0x10000000 | OPC_MOVE)
 963
 964#define SCR_CHMOV_ABS(l) ((0x00000000) | (l))
 965#define SCR_CHMOV_IND(l) ((0x20000000) | (l))
 966#define SCR_CHMOV_TBL     (0x10000000)
 967
 968struct scr_tblmove {
 969        u32  size;
 970        u32  addr;
 971};
 972
 973/*-----------------------------------------------------------
 974**
 975**      Selection
 976**
 977**-----------------------------------------------------------
 978**
 979**      SEL_ABS | SCR_ID (0..15)    [ | REL_JMP]
 980**      <<alternate_address>>
 981**
 982**      SEL_TBL | << dnad_offset>>  [ | REL_JMP]
 983**      <<alternate_address>>
 984**
 985**-----------------------------------------------------------
 986*/
 987
 988#define SCR_SEL_ABS     0x40000000
 989#define SCR_SEL_ABS_ATN 0x41000000
 990#define SCR_SEL_TBL     0x42000000
 991#define SCR_SEL_TBL_ATN 0x43000000
 992
 993
 994#ifdef SCSI_NCR_BIG_ENDIAN
 995struct scr_tblsel {
 996        u8      sel_scntl3;
 997        u8      sel_id;
 998        u8      sel_sxfer;
 999        u8      sel_scntl4;     
1000};
1001#else
1002struct scr_tblsel {
1003        u8      sel_scntl4;     
1004        u8      sel_sxfer;
1005        u8      sel_id;
1006        u8      sel_scntl3;
1007};
1008#endif
1009
1010#define SCR_JMP_REL     0x04000000
1011#define SCR_ID(id)      (((u32)(id)) << 16)
1012
1013/*-----------------------------------------------------------
1014**
1015**      Waiting for Disconnect or Reselect
1016**
1017**-----------------------------------------------------------
1018**
1019**      WAIT_DISC
1020**      dummy: <<alternate_address>>
1021**
1022**      WAIT_RESEL
1023**      <<alternate_address>>
1024**
1025**-----------------------------------------------------------
1026*/
1027
1028#define SCR_WAIT_DISC   0x48000000
1029#define SCR_WAIT_RESEL  0x50000000
1030
1031/*-----------------------------------------------------------
1032**
1033**      Bit Set / Reset
1034**
1035**-----------------------------------------------------------
1036**
1037**      SET (flags {|.. })
1038**
1039**      CLR (flags {|.. })
1040**
1041**-----------------------------------------------------------
1042*/
1043
1044#define SCR_SET(f)     (0x58000000 | (f))
1045#define SCR_CLR(f)     (0x60000000 | (f))
1046
1047#define SCR_CARRY       0x00000400
1048#define SCR_TRG         0x00000200
1049#define SCR_ACK         0x00000040
1050#define SCR_ATN         0x00000008
1051
1052
1053
1054
1055/*-----------------------------------------------------------
1056**
1057**      Memory to memory move
1058**
1059**-----------------------------------------------------------
1060**
1061**      COPY (bytecount)
1062**      << source_address >>
1063**      << destination_address >>
1064**
1065**      SCR_COPY   sets the NO FLUSH option by default.
1066**      SCR_COPY_F does not set this option.
1067**
1068**      For chips which do not support this option,
1069**      ncr_copy_and_bind() will remove this bit.
1070**-----------------------------------------------------------
1071*/
1072
1073#define SCR_NO_FLUSH 0x01000000
1074
1075#define SCR_COPY(n) (0xc0000000 | SCR_NO_FLUSH | (n))
1076#define SCR_COPY_F(n) (0xc0000000 | (n))
1077
1078/*-----------------------------------------------------------
1079**
1080**      Register move and binary operations
1081**
1082**-----------------------------------------------------------
1083**
1084**      SFBR_REG (reg, op, data)        reg  = SFBR op data
1085**      << 0 >>
1086**
1087**      REG_SFBR (reg, op, data)        SFBR = reg op data
1088**      << 0 >>
1089**
1090**      REG_REG  (reg, op, data)        reg  = reg op data
1091**      << 0 >>
1092**
1093**-----------------------------------------------------------
1094**      On 810A, 860, 825A, 875, 895 and 896 chips the content 
1095**      of SFBR register can be used as data (SCR_SFBR_DATA).
1096**      The 896 has additional IO registers starting at 
1097**      offset 0x80. Bit 7 of register offset is stored in 
1098**      bit 7 of the SCRIPTS instruction first DWORD.
1099**-----------------------------------------------------------
1100*/
1101
1102#define SCR_REG_OFS(ofs) ((((ofs) & 0x7f) << 16ul) + ((ofs) & 0x80)) 
1103
1104#define SCR_SFBR_REG(reg,op,data) \
1105        (0x68000000 | (SCR_REG_OFS(REG(reg))) | (op) | (((data)&0xff)<<8ul))
1106
1107#define SCR_REG_SFBR(reg,op,data) \
1108        (0x70000000 | (SCR_REG_OFS(REG(reg))) | (op) | (((data)&0xff)<<8ul))
1109
1110#define SCR_REG_REG(reg,op,data) \
1111        (0x78000000 | (SCR_REG_OFS(REG(reg))) | (op) | (((data)&0xff)<<8ul))
1112
1113
1114#define      SCR_LOAD   0x00000000
1115#define      SCR_SHL    0x01000000
1116#define      SCR_OR     0x02000000
1117#define      SCR_XOR    0x03000000
1118#define      SCR_AND    0x04000000
1119#define      SCR_SHR    0x05000000
1120#define      SCR_ADD    0x06000000
1121#define      SCR_ADDC   0x07000000
1122
1123#define      SCR_SFBR_DATA   (0x00800000>>8ul)  /* Use SFBR as data */
1124
1125/*-----------------------------------------------------------
1126**
1127**      FROM_REG (reg)            SFBR = reg
1128**      << 0 >>
1129**
1130**      TO_REG   (reg)            reg  = SFBR
1131**      << 0 >>
1132**
1133**      LOAD_REG (reg, data)      reg  = <data>
1134**      << 0 >>
1135**
1136**      LOAD_SFBR(data)           SFBR = <data>
1137**      << 0 >>
1138**
1139**-----------------------------------------------------------
1140*/
1141
1142#define SCR_FROM_REG(reg) \
1143        SCR_REG_SFBR(reg,SCR_OR,0)
1144
1145#define SCR_TO_REG(reg) \
1146        SCR_SFBR_REG(reg,SCR_OR,0)
1147
1148#define SCR_LOAD_REG(reg,data) \
1149        SCR_REG_REG(reg,SCR_LOAD,data)
1150
1151#define SCR_LOAD_SFBR(data) \
1152        (SCR_REG_SFBR (gpreg, SCR_LOAD, data))
1153
1154/*-----------------------------------------------------------
1155**
1156**      LOAD  from memory   to register.
1157**      STORE from register to memory.
1158**
1159**      Only supported by 810A, 860, 825A, 875, 895 and 896.
1160**
1161**-----------------------------------------------------------
1162**
1163**      LOAD_ABS (LEN)
1164**      <<start address>>
1165**
1166**      LOAD_REL (LEN)        (DSA relative)
1167**      <<dsa_offset>>
1168**
1169**-----------------------------------------------------------
1170*/
1171
1172#define SCR_REG_OFS2(ofs) (((ofs) & 0xff) << 16ul)
1173#define SCR_NO_FLUSH2   0x02000000
1174#define SCR_DSA_REL2    0x10000000
1175
1176#define SCR_LOAD_R(reg, how, n) \
1177        (0xe1000000 | how | (SCR_REG_OFS2(REG(reg))) | (n))
1178
1179#define SCR_STORE_R(reg, how, n) \
1180        (0xe0000000 | how | (SCR_REG_OFS2(REG(reg))) | (n))
1181
1182#define SCR_LOAD_ABS(reg, n)    SCR_LOAD_R(reg, SCR_NO_FLUSH2, n)
1183#define SCR_LOAD_REL(reg, n)    SCR_LOAD_R(reg, SCR_NO_FLUSH2|SCR_DSA_REL2, n)
1184#define SCR_LOAD_ABS_F(reg, n)  SCR_LOAD_R(reg, 0, n)
1185#define SCR_LOAD_REL_F(reg, n)  SCR_LOAD_R(reg, SCR_DSA_REL2, n)
1186
1187#define SCR_STORE_ABS(reg, n)   SCR_STORE_R(reg, SCR_NO_FLUSH2, n)
1188#define SCR_STORE_REL(reg, n)   SCR_STORE_R(reg, SCR_NO_FLUSH2|SCR_DSA_REL2,n)
1189#define SCR_STORE_ABS_F(reg, n) SCR_STORE_R(reg, 0, n)
1190#define SCR_STORE_REL_F(reg, n) SCR_STORE_R(reg, SCR_DSA_REL2, n)
1191
1192
1193/*-----------------------------------------------------------
1194**
1195**      Waiting for Disconnect or Reselect
1196**
1197**-----------------------------------------------------------
1198**
1199**      JUMP            [ | IFTRUE/IFFALSE ( ... ) ]
1200**      <<address>>
1201**
1202**      JUMPR           [ | IFTRUE/IFFALSE ( ... ) ]
1203**      <<distance>>
1204**
1205**      CALL            [ | IFTRUE/IFFALSE ( ... ) ]
1206**      <<address>>
1207**
1208**      CALLR           [ | IFTRUE/IFFALSE ( ... ) ]
1209**      <<distance>>
1210**
1211**      RETURN          [ | IFTRUE/IFFALSE ( ... ) ]
1212**      <<dummy>>
1213**
1214**      INT             [ | IFTRUE/IFFALSE ( ... ) ]
1215**      <<ident>>
1216**
1217**      INT_FLY         [ | IFTRUE/IFFALSE ( ... ) ]
1218**      <<ident>>
1219**
1220**      Conditions:
1221**           WHEN (phase)
1222**           IF   (phase)
1223**           CARRYSET
1224**           DATA (data, mask)
1225**
1226**-----------------------------------------------------------
1227*/
1228
1229#define SCR_NO_OP       0x80000000
1230#define SCR_JUMP        0x80080000
1231#define SCR_JUMP64      0x80480000
1232#define SCR_JUMPR       0x80880000
1233#define SCR_CALL        0x88080000
1234#define SCR_CALLR       0x88880000
1235#define SCR_RETURN      0x90080000
1236#define SCR_INT         0x98080000
1237#define SCR_INT_FLY     0x98180000
1238
1239#define IFFALSE(arg)   (0x00080000 | (arg))
1240#define IFTRUE(arg)    (0x00000000 | (arg))
1241
1242#define WHEN(phase)    (0x00030000 | (phase))
1243#define IF(phase)      (0x00020000 | (phase))
1244
1245#define DATA(D)        (0x00040000 | ((D) & 0xff))
1246#define MASK(D,M)      (0x00040000 | (((M ^ 0xff) & 0xff) << 8ul)|((D) & 0xff))
1247
1248#define CARRYSET       (0x00200000)
1249
1250/*-----------------------------------------------------------
1251**
1252**      SCSI  constants.
1253**
1254**-----------------------------------------------------------
1255*/
1256
1257/*
1258**      Status
1259*/
1260
1261#define S_GOOD          (0x00)
1262#define S_CHECK_COND    (0x02)
1263#define S_COND_MET      (0x04)
1264#define S_BUSY          (0x08)
1265#define S_INT           (0x10)
1266#define S_INT_COND_MET  (0x14)
1267#define S_CONFLICT      (0x18)
1268#define S_TERMINATED    (0x20)
1269#define S_QUEUE_FULL    (0x28)
1270#define S_ILLEGAL       (0xff)
1271#define S_SENSE         (0x80)
1272
1273/*
1274 * End of ncrreg from FreeBSD
1275 */
1276
1277/*
1278        Build a scatter/gather entry.
1279        see sym53c8xx_2/sym_hipd.h for more detailed sym_build_sge()
1280        implementation ;)
1281 */
1282
1283#define ncr_build_sge(np, data, badd, len)      \
1284do {                                            \
1285        (data)->addr = cpu_to_scr(badd);        \
1286        (data)->size = cpu_to_scr(len);         \
1287} while (0)
1288
1289/*==========================================================
1290**
1291**      Structures used by the detection routine to transmit 
1292**      device configuration to the attach function.
1293**
1294**==========================================================
1295*/
1296struct ncr_slot {
1297        u_long  base;
1298        u_long  base_2;
1299        u_long  base_c;
1300        u_long  base_2_c;
1301        void __iomem *base_v;
1302        void __iomem *base_2_v;
1303        int     irq;
1304/* port and reg fields to use INB, OUTB macros */
1305        volatile struct ncr_reg __iomem *reg;
1306};
1307
1308/*==========================================================
1309**
1310**      Structure used by detection routine to save data on 
1311**      each detected board for attach.
1312**
1313**==========================================================
1314*/
1315struct ncr_device {
1316        struct device  *dev;
1317        struct ncr_slot  slot;
1318        struct ncr_chip  chip;
1319        u_char host_id;
1320        u8 differential;
1321};
1322
1323extern struct Scsi_Host *ncr_attach(struct scsi_host_template *tpnt, int unit, struct ncr_device *device);
1324extern void ncr53c8xx_release(struct Scsi_Host *host);
1325irqreturn_t ncr53c8xx_intr(int irq, void *dev_id);
1326extern int ncr53c8xx_init(void);
1327extern void ncr53c8xx_exit(void);
1328
1329#endif /* NCR53C8XX_H */
1330
lxr.linux.no kindly hosted by Redpill Linpro AS, provider of Linux consulting and operations services since 1995.