linux/drivers/spi/spi-xilinx.c
<<
>>
Prefs
   1/*
   2 * Xilinx SPI controller driver (master mode only)
   3 *
   4 * Author: MontaVista Software, Inc.
   5 *      source@mvista.com
   6 *
   7 * Copyright (c) 2010 Secret Lab Technologies, Ltd.
   8 * Copyright (c) 2009 Intel Corporation
   9 * 2002-2007 (c) MontaVista Software, Inc.
  10
  11 * This program is free software; you can redistribute it and/or modify
  12 * it under the terms of the GNU General Public License version 2 as
  13 * published by the Free Software Foundation.
  14 */
  15
  16#include <linux/module.h>
  17#include <linux/init.h>
  18#include <linux/interrupt.h>
  19#include <linux/of.h>
  20#include <linux/platform_device.h>
  21#include <linux/spi/spi.h>
  22#include <linux/spi/spi_bitbang.h>
  23#include <linux/spi/xilinx_spi.h>
  24#include <linux/io.h>
  25
  26#define XILINX_SPI_NAME "xilinx_spi"
  27
  28/* Register definitions as per "OPB Serial Peripheral Interface (SPI) (v1.00e)
  29 * Product Specification", DS464
  30 */
  31#define XSPI_CR_OFFSET          0x60    /* Control Register */
  32
  33#define XSPI_CR_ENABLE          0x02
  34#define XSPI_CR_MASTER_MODE     0x04
  35#define XSPI_CR_CPOL            0x08
  36#define XSPI_CR_CPHA            0x10
  37#define XSPI_CR_MODE_MASK       (XSPI_CR_CPHA | XSPI_CR_CPOL)
  38#define XSPI_CR_TXFIFO_RESET    0x20
  39#define XSPI_CR_RXFIFO_RESET    0x40
  40#define XSPI_CR_MANUAL_SSELECT  0x80
  41#define XSPI_CR_TRANS_INHIBIT   0x100
  42#define XSPI_CR_LSB_FIRST       0x200
  43
  44#define XSPI_SR_OFFSET          0x64    /* Status Register */
  45
  46#define XSPI_SR_RX_EMPTY_MASK   0x01    /* Receive FIFO is empty */
  47#define XSPI_SR_RX_FULL_MASK    0x02    /* Receive FIFO is full */
  48#define XSPI_SR_TX_EMPTY_MASK   0x04    /* Transmit FIFO is empty */
  49#define XSPI_SR_TX_FULL_MASK    0x08    /* Transmit FIFO is full */
  50#define XSPI_SR_MODE_FAULT_MASK 0x10    /* Mode fault error */
  51
  52#define XSPI_TXD_OFFSET         0x68    /* Data Transmit Register */
  53#define XSPI_RXD_OFFSET         0x6c    /* Data Receive Register */
  54
  55#define XSPI_SSR_OFFSET         0x70    /* 32-bit Slave Select Register */
  56
  57/* Register definitions as per "OPB IPIF (v3.01c) Product Specification", DS414
  58 * IPIF registers are 32 bit
  59 */
  60#define XIPIF_V123B_DGIER_OFFSET        0x1c    /* IPIF global int enable reg */
  61#define XIPIF_V123B_GINTR_ENABLE        0x80000000
  62
  63#define XIPIF_V123B_IISR_OFFSET         0x20    /* IPIF interrupt status reg */
  64#define XIPIF_V123B_IIER_OFFSET         0x28    /* IPIF interrupt enable reg */
  65
  66#define XSPI_INTR_MODE_FAULT            0x01    /* Mode fault error */
  67#define XSPI_INTR_SLAVE_MODE_FAULT      0x02    /* Selected as slave while
  68                                                 * disabled */
  69#define XSPI_INTR_TX_EMPTY              0x04    /* TxFIFO is empty */
  70#define XSPI_INTR_TX_UNDERRUN           0x08    /* TxFIFO was underrun */
  71#define XSPI_INTR_RX_FULL               0x10    /* RxFIFO is full */
  72#define XSPI_INTR_RX_OVERRUN            0x20    /* RxFIFO was overrun */
  73#define XSPI_INTR_TX_HALF_EMPTY         0x40    /* TxFIFO is half empty */
  74
  75#define XIPIF_V123B_RESETR_OFFSET       0x40    /* IPIF reset register */
  76#define XIPIF_V123B_RESET_MASK          0x0a    /* the value to write */
  77
  78struct xilinx_spi {
  79        /* bitbang has to be first */
  80        struct spi_bitbang bitbang;
  81        struct completion done;
  82        struct resource mem; /* phys mem */
  83        void __iomem    *regs;  /* virt. address of the control registers */
  84
  85        u32             irq;
  86
  87        u8 *rx_ptr;             /* pointer in the Tx buffer */
  88        const u8 *tx_ptr;       /* pointer in the Rx buffer */
  89        int remaining_bytes;    /* the number of bytes left to transfer */
  90        u8 bits_per_word;
  91        unsigned int (*read_fn) (void __iomem *);
  92        void (*write_fn) (u32, void __iomem *);
  93        void (*tx_fn) (struct xilinx_spi *);
  94        void (*rx_fn) (struct xilinx_spi *);
  95};
  96
  97static void xspi_write32(u32 val, void __iomem *addr)
  98{
  99        iowrite32(val, addr);
 100}
 101
 102static unsigned int xspi_read32(void __iomem *addr)
 103{
 104        return ioread32(addr);
 105}
 106
 107static void xspi_write32_be(u32 val, void __iomem *addr)
 108{
 109        iowrite32be(val, addr);
 110}
 111
 112static unsigned int xspi_read32_be(void __iomem *addr)
 113{
 114        return ioread32be(addr);
 115}
 116
 117static void xspi_tx8(struct xilinx_spi *xspi)
 118{
 119        xspi->write_fn(*xspi->tx_ptr, xspi->regs + XSPI_TXD_OFFSET);
 120        xspi->tx_ptr++;
 121}
 122
 123static void xspi_tx16(struct xilinx_spi *xspi)
 124{
 125        xspi->write_fn(*(u16 *)(xspi->tx_ptr), xspi->regs + XSPI_TXD_OFFSET);
 126        xspi->tx_ptr += 2;
 127}
 128
 129static void xspi_tx32(struct xilinx_spi *xspi)
 130{
 131        xspi->write_fn(*(u32 *)(xspi->tx_ptr), xspi->regs + XSPI_TXD_OFFSET);
 132        xspi->tx_ptr += 4;
 133}
 134
 135static void xspi_rx8(struct xilinx_spi *xspi)
 136{
 137        u32 data = xspi->read_fn(xspi->regs + XSPI_RXD_OFFSET);
 138        if (xspi->rx_ptr) {
 139                *xspi->rx_ptr = data & 0xff;
 140                xspi->rx_ptr++;
 141        }
 142}
 143
 144static void xspi_rx16(struct xilinx_spi *xspi)
 145{
 146        u32 data = xspi->read_fn(xspi->regs + XSPI_RXD_OFFSET);
 147        if (xspi->rx_ptr) {
 148                *(u16 *)(xspi->rx_ptr) = data & 0xffff;
 149                xspi->rx_ptr += 2;
 150        }
 151}
 152
 153static void xspi_rx32(struct xilinx_spi *xspi)
 154{
 155        u32 data = xspi->read_fn(xspi->regs + XSPI_RXD_OFFSET);
 156        if (xspi->rx_ptr) {
 157                *(u32 *)(xspi->rx_ptr) = data;
 158                xspi->rx_ptr += 4;
 159        }
 160}
 161
 162static void xspi_init_hw(struct xilinx_spi *xspi)
 163{
 164        void __iomem *regs_base = xspi->regs;
 165
 166        /* Reset the SPI device */
 167        xspi->write_fn(XIPIF_V123B_RESET_MASK,
 168                regs_base + XIPIF_V123B_RESETR_OFFSET);
 169        /* Disable all the interrupts just in case */
 170        xspi->write_fn(0, regs_base + XIPIF_V123B_IIER_OFFSET);
 171        /* Enable the global IPIF interrupt */
 172        xspi->write_fn(XIPIF_V123B_GINTR_ENABLE,
 173                regs_base + XIPIF_V123B_DGIER_OFFSET);
 174        /* Deselect the slave on the SPI bus */
 175        xspi->write_fn(0xffff, regs_base + XSPI_SSR_OFFSET);
 176        /* Disable the transmitter, enable Manual Slave Select Assertion,
 177         * put SPI controller into master mode, and enable it */
 178        xspi->write_fn(XSPI_CR_TRANS_INHIBIT | XSPI_CR_MANUAL_SSELECT |
 179                XSPI_CR_MASTER_MODE | XSPI_CR_ENABLE | XSPI_CR_TXFIFO_RESET |
 180                XSPI_CR_RXFIFO_RESET, regs_base + XSPI_CR_OFFSET);
 181}
 182
 183static void xilinx_spi_chipselect(struct spi_device *spi, int is_on)
 184{
 185        struct xilinx_spi *xspi = spi_master_get_devdata(spi->master);
 186
 187        if (is_on == BITBANG_CS_INACTIVE) {
 188                /* Deselect the slave on the SPI bus */
 189                xspi->write_fn(0xffff, xspi->regs + XSPI_SSR_OFFSET);
 190        } else if (is_on == BITBANG_CS_ACTIVE) {
 191                /* Set the SPI clock phase and polarity */
 192                u16 cr = xspi->read_fn(xspi->regs + XSPI_CR_OFFSET)
 193                         & ~XSPI_CR_MODE_MASK;
 194                if (spi->mode & SPI_CPHA)
 195                        cr |= XSPI_CR_CPHA;
 196                if (spi->mode & SPI_CPOL)
 197                        cr |= XSPI_CR_CPOL;
 198                xspi->write_fn(cr, xspi->regs + XSPI_CR_OFFSET);
 199
 200                /* We do not check spi->max_speed_hz here as the SPI clock
 201                 * frequency is not software programmable (the IP block design
 202                 * parameter)
 203                 */
 204
 205                /* Activate the chip select */
 206                xspi->write_fn(~(0x0001 << spi->chip_select),
 207                        xspi->regs + XSPI_SSR_OFFSET);
 208        }
 209}
 210
 211/* spi_bitbang requires custom setup_transfer() to be defined if there is a
 212 * custom txrx_bufs(). We have nothing to setup here as the SPI IP block
 213 * supports 8 or 16 bits per word which cannot be changed in software.
 214 * SPI clock can't be changed in software either.
 215 * Check for correct bits per word. Chip select delay calculations could be
 216 * added here as soon as bitbang_work() can be made aware of the delay value.
 217 */
 218static int xilinx_spi_setup_transfer(struct spi_device *spi,
 219                struct spi_transfer *t)
 220{
 221        struct xilinx_spi *xspi = spi_master_get_devdata(spi->master);
 222        u8 bits_per_word;
 223
 224        bits_per_word = (t && t->bits_per_word)
 225                         ? t->bits_per_word : spi->bits_per_word;
 226        if (bits_per_word != xspi->bits_per_word) {
 227                dev_err(&spi->dev, "%s, unsupported bits_per_word=%d\n",
 228                        __func__, bits_per_word);
 229                return -EINVAL;
 230        }
 231
 232        return 0;
 233}
 234
 235static int xilinx_spi_setup(struct spi_device *spi)
 236{
 237        /* always return 0, we can not check the number of bits.
 238         * There are cases when SPI setup is called before any driver is
 239         * there, in that case the SPI core defaults to 8 bits, which we
 240         * do not support in some cases. But if we return an error, the
 241         * SPI device would not be registered and no driver can get hold of it
 242         * When the driver is there, it will call SPI setup again with the
 243         * correct number of bits per transfer.
 244         * If a driver setups with the wrong bit number, it will fail when
 245         * it tries to do a transfer
 246         */
 247        return 0;
 248}
 249
 250static void xilinx_spi_fill_tx_fifo(struct xilinx_spi *xspi)
 251{
 252        u8 sr;
 253
 254        /* Fill the Tx FIFO with as many bytes as possible */
 255        sr = xspi->read_fn(xspi->regs + XSPI_SR_OFFSET);
 256        while ((sr & XSPI_SR_TX_FULL_MASK) == 0 && xspi->remaining_bytes > 0) {
 257                if (xspi->tx_ptr)
 258                        xspi->tx_fn(xspi);
 259                else
 260                        xspi->write_fn(0, xspi->regs + XSPI_TXD_OFFSET);
 261                xspi->remaining_bytes -= xspi->bits_per_word / 8;
 262                sr = xspi->read_fn(xspi->regs + XSPI_SR_OFFSET);
 263        }
 264}
 265
 266static int xilinx_spi_txrx_bufs(struct spi_device *spi, struct spi_transfer *t)
 267{
 268        struct xilinx_spi *xspi = spi_master_get_devdata(spi->master);
 269        u32 ipif_ier;
 270        u16 cr;
 271
 272        /* We get here with transmitter inhibited */
 273
 274        xspi->tx_ptr = t->tx_buf;
 275        xspi->rx_ptr = t->rx_buf;
 276        xspi->remaining_bytes = t->len;
 277        INIT_COMPLETION(xspi->done);
 278
 279        xilinx_spi_fill_tx_fifo(xspi);
 280
 281        /* Enable the transmit empty interrupt, which we use to determine
 282         * progress on the transmission.
 283         */
 284        ipif_ier = xspi->read_fn(xspi->regs + XIPIF_V123B_IIER_OFFSET);
 285        xspi->write_fn(ipif_ier | XSPI_INTR_TX_EMPTY,
 286                xspi->regs + XIPIF_V123B_IIER_OFFSET);
 287
 288        /* Start the transfer by not inhibiting the transmitter any longer */
 289        cr = xspi->read_fn(xspi->regs + XSPI_CR_OFFSET) &
 290                ~XSPI_CR_TRANS_INHIBIT;
 291        xspi->write_fn(cr, xspi->regs + XSPI_CR_OFFSET);
 292
 293        wait_for_completion(&xspi->done);
 294
 295        /* Disable the transmit empty interrupt */
 296        xspi->write_fn(ipif_ier, xspi->regs + XIPIF_V123B_IIER_OFFSET);
 297
 298        return t->len - xspi->remaining_bytes;
 299}
 300
 301
 302/* This driver supports single master mode only. Hence Tx FIFO Empty
 303 * is the only interrupt we care about.
 304 * Receive FIFO Overrun, Transmit FIFO Underrun, Mode Fault, and Slave Mode
 305 * Fault are not to happen.
 306 */
 307static irqreturn_t xilinx_spi_irq(int irq, void *dev_id)
 308{
 309        struct xilinx_spi *xspi = dev_id;
 310        u32 ipif_isr;
 311
 312        /* Get the IPIF interrupts, and clear them immediately */
 313        ipif_isr = xspi->read_fn(xspi->regs + XIPIF_V123B_IISR_OFFSET);
 314        xspi->write_fn(ipif_isr, xspi->regs + XIPIF_V123B_IISR_OFFSET);
 315
 316        if (ipif_isr & XSPI_INTR_TX_EMPTY) {    /* Transmission completed */
 317                u16 cr;
 318                u8 sr;
 319
 320                /* A transmit has just completed. Process received data and
 321                 * check for more data to transmit. Always inhibit the
 322                 * transmitter while the Isr refills the transmit register/FIFO,
 323                 * or make sure it is stopped if we're done.
 324                 */
 325                cr = xspi->read_fn(xspi->regs + XSPI_CR_OFFSET);
 326                xspi->write_fn(cr | XSPI_CR_TRANS_INHIBIT,
 327                        xspi->regs + XSPI_CR_OFFSET);
 328
 329                /* Read out all the data from the Rx FIFO */
 330                sr = xspi->read_fn(xspi->regs + XSPI_SR_OFFSET);
 331                while ((sr & XSPI_SR_RX_EMPTY_MASK) == 0) {
 332                        xspi->rx_fn(xspi);
 333                        sr = xspi->read_fn(xspi->regs + XSPI_SR_OFFSET);
 334                }
 335
 336                /* See if there is more data to send */
 337                if (xspi->remaining_bytes > 0) {
 338                        xilinx_spi_fill_tx_fifo(xspi);
 339                        /* Start the transfer by not inhibiting the
 340                         * transmitter any longer
 341                         */
 342                        xspi->write_fn(cr, xspi->regs + XSPI_CR_OFFSET);
 343                } else {
 344                        /* No more data to send.
 345                         * Indicate the transfer is completed.
 346                         */
 347                        complete(&xspi->done);
 348                }
 349        }
 350
 351        return IRQ_HANDLED;
 352}
 353
 354static const struct of_device_id xilinx_spi_of_match[] = {
 355        { .compatible = "xlnx,xps-spi-2.00.a", },
 356        { .compatible = "xlnx,xps-spi-2.00.b", },
 357        {}
 358};
 359MODULE_DEVICE_TABLE(of, xilinx_spi_of_match);
 360
 361struct spi_master *xilinx_spi_init(struct device *dev, struct resource *mem,
 362        u32 irq, s16 bus_num, int num_cs, int little_endian, int bits_per_word)
 363{
 364        struct spi_master *master;
 365        struct xilinx_spi *xspi;
 366        int ret;
 367
 368        master = spi_alloc_master(dev, sizeof(struct xilinx_spi));
 369        if (!master)
 370                return NULL;
 371
 372        /* the spi->mode bits understood by this driver: */
 373        master->mode_bits = SPI_CPOL | SPI_CPHA;
 374
 375        xspi = spi_master_get_devdata(master);
 376        xspi->bitbang.master = spi_master_get(master);
 377        xspi->bitbang.chipselect = xilinx_spi_chipselect;
 378        xspi->bitbang.setup_transfer = xilinx_spi_setup_transfer;
 379        xspi->bitbang.txrx_bufs = xilinx_spi_txrx_bufs;
 380        xspi->bitbang.master->setup = xilinx_spi_setup;
 381        init_completion(&xspi->done);
 382
 383        if (!request_mem_region(mem->start, resource_size(mem),
 384                XILINX_SPI_NAME))
 385                goto put_master;
 386
 387        xspi->regs = ioremap(mem->start, resource_size(mem));
 388        if (xspi->regs == NULL) {
 389                dev_warn(dev, "ioremap failure\n");
 390                goto map_failed;
 391        }
 392
 393        master->bus_num = bus_num;
 394        master->num_chipselect = num_cs;
 395        master->dev.of_node = dev->of_node;
 396
 397        xspi->mem = *mem;
 398        xspi->irq = irq;
 399        if (little_endian) {
 400                xspi->read_fn = xspi_read32;
 401                xspi->write_fn = xspi_write32;
 402        } else {
 403                xspi->read_fn = xspi_read32_be;
 404                xspi->write_fn = xspi_write32_be;
 405        }
 406        xspi->bits_per_word = bits_per_word;
 407        if (xspi->bits_per_word == 8) {
 408                xspi->tx_fn = xspi_tx8;
 409                xspi->rx_fn = xspi_rx8;
 410        } else if (xspi->bits_per_word == 16) {
 411                xspi->tx_fn = xspi_tx16;
 412                xspi->rx_fn = xspi_rx16;
 413        } else if (xspi->bits_per_word == 32) {
 414                xspi->tx_fn = xspi_tx32;
 415                xspi->rx_fn = xspi_rx32;
 416        } else
 417                goto unmap_io;
 418
 419
 420        /* SPI controller initializations */
 421        xspi_init_hw(xspi);
 422
 423        /* Register for SPI Interrupt */
 424        ret = request_irq(xspi->irq, xilinx_spi_irq, 0, XILINX_SPI_NAME, xspi);
 425        if (ret)
 426                goto unmap_io;
 427
 428        ret = spi_bitbang_start(&xspi->bitbang);
 429        if (ret) {
 430                dev_err(dev, "spi_bitbang_start FAILED\n");
 431                goto free_irq;
 432        }
 433
 434        dev_info(dev, "at 0x%08llX mapped to 0x%p, irq=%d\n",
 435                (unsigned long long)mem->start, xspi->regs, xspi->irq);
 436        return master;
 437
 438free_irq:
 439        free_irq(xspi->irq, xspi);
 440unmap_io:
 441        iounmap(xspi->regs);
 442map_failed:
 443        release_mem_region(mem->start, resource_size(mem));
 444put_master:
 445        spi_master_put(master);
 446        return NULL;
 447}
 448EXPORT_SYMBOL(xilinx_spi_init);
 449
 450void xilinx_spi_deinit(struct spi_master *master)
 451{
 452        struct xilinx_spi *xspi;
 453
 454        xspi = spi_master_get_devdata(master);
 455
 456        spi_bitbang_stop(&xspi->bitbang);
 457        free_irq(xspi->irq, xspi);
 458        iounmap(xspi->regs);
 459
 460        release_mem_region(xspi->mem.start, resource_size(&xspi->mem));
 461        spi_master_put(xspi->bitbang.master);
 462}
 463EXPORT_SYMBOL(xilinx_spi_deinit);
 464
 465static int __devinit xilinx_spi_probe(struct platform_device *dev)
 466{
 467        struct xspi_platform_data *pdata;
 468        struct resource *r;
 469        int irq, num_cs = 0, little_endian = 0, bits_per_word = 8;
 470        struct spi_master *master;
 471        u8 i;
 472
 473        pdata = dev->dev.platform_data;
 474        if (pdata) {
 475                num_cs = pdata->num_chipselect;
 476                little_endian = pdata->little_endian;
 477                bits_per_word = pdata->bits_per_word;
 478        }
 479
 480#ifdef CONFIG_OF
 481        if (dev->dev.of_node) {
 482                const __be32 *prop;
 483                int len;
 484
 485                /* number of slave select bits is required */
 486                prop = of_get_property(dev->dev.of_node, "xlnx,num-ss-bits",
 487                                       &len);
 488                if (prop && len >= sizeof(*prop))
 489                        num_cs = __be32_to_cpup(prop);
 490        }
 491#endif
 492
 493        if (!num_cs) {
 494                dev_err(&dev->dev, "Missing slave select configuration data\n");
 495                return -EINVAL;
 496        }
 497
 498
 499        r = platform_get_resource(dev, IORESOURCE_MEM, 0);
 500        if (!r)
 501                return -ENODEV;
 502
 503        irq = platform_get_irq(dev, 0);
 504        if (irq < 0)
 505                return -ENXIO;
 506
 507        master = xilinx_spi_init(&dev->dev, r, irq, dev->id, num_cs,
 508                                 little_endian, bits_per_word);
 509        if (!master)
 510                return -ENODEV;
 511
 512        if (pdata) {
 513                for (i = 0; i < pdata->num_devices; i++)
 514                        spi_new_device(master, pdata->devices + i);
 515        }
 516
 517        platform_set_drvdata(dev, master);
 518        return 0;
 519}
 520
 521static int __devexit xilinx_spi_remove(struct platform_device *dev)
 522{
 523        xilinx_spi_deinit(platform_get_drvdata(dev));
 524        platform_set_drvdata(dev, 0);
 525
 526        return 0;
 527}
 528
 529/* work with hotplug and coldplug */
 530MODULE_ALIAS("platform:" XILINX_SPI_NAME);
 531
 532static struct platform_driver xilinx_spi_driver = {
 533        .probe = xilinx_spi_probe,
 534        .remove = __devexit_p(xilinx_spi_remove),
 535        .driver = {
 536                .name = XILINX_SPI_NAME,
 537                .owner = THIS_MODULE,
 538                .of_match_table = xilinx_spi_of_match,
 539        },
 540};
 541module_platform_driver(xilinx_spi_driver);
 542
 543MODULE_AUTHOR("MontaVista Software, Inc. <source@mvista.com>");
 544MODULE_DESCRIPTION("Xilinx SPI driver");
 545MODULE_LICENSE("GPL");
 546
lxr.linux.no kindly hosted by Redpill Linpro AS, provider of Linux consulting and operations services since 1995.