2System Power Management States
   5The kernel supports four power management states generically, though
   6one is generic and the other three are dependent on platform support
   7code to implement the low-level details for each state.
   8This file describes each state, what they are
   9commonly called, what ACPI state they map to, and what string to write
  10to /sys/power/state to enter that state
  12state:          Freeze / Low-Power Idle
  13ACPI state:     S0
  14String:         "freeze"
  16This state is a generic, pure software, light-weight, low-power state.
  17It allows more energy to be saved relative to idle by freezing user
  18space and putting all I/O devices into low-power states (possibly
  19lower-power than available at run time), such that the processors can
  20spend more time in their idle states.
  21This state can be used for platforms without Standby/Suspend-to-RAM
  22support, or it can be used in addition to Suspend-to-RAM (memory sleep)
  23to provide reduced resume latency.
  26State:          Standby / Power-On Suspend
  27ACPI State:     S1
  28String:         "standby"
  30This state offers minimal, though real, power savings, while providing
  31a very low-latency transition back to a working system. No operating
  32state is lost (the CPU retains power), so the system easily starts up
  33again where it left off. 
  35We try to put devices in a low-power state equivalent to D1, which
  36also offers low power savings, but low resume latency. Not all devices
  37support D1, and those that don't are left on. 
  40State:          Suspend-to-RAM
  41ACPI State:     S3
  42String:         "mem"
  44This state offers significant power savings as everything in the
  45system is put into a low-power state, except for memory, which is
  46placed in self-refresh mode to retain its contents. 
  48System and device state is saved and kept in memory. All devices are
  49suspended and put into D3. In many cases, all peripheral buses lose
  50power when entering STR, so devices must be able to handle the
  51transition back to the On state. 
  53For at least ACPI, STR requires some minimal boot-strapping code to
  54resume the system from STR. This may be true on other platforms. 
  57State:          Suspend-to-disk
  58ACPI State:     S4
  59String:         "disk"
  61This state offers the greatest power savings, and can be used even in
  62the absence of low-level platform support for power management. This
  63state operates similarly to Suspend-to-RAM, but includes a final step
  64of writing memory contents to disk. On resume, this is read and memory
  65is restored to its pre-suspend state. 
  67STD can be handled by the firmware or the kernel. If it is handled by
  68the firmware, it usually requires a dedicated partition that must be
  69setup via another operating system for it to use. Despite the
  70inconvenience, this method requires minimal work by the kernel, since
  71the firmware will also handle restoring memory contents on resume. 
  73For suspend-to-disk, a mechanism called 'swsusp' (Swap Suspend) is used
  74to write memory contents to free swap space. swsusp has some restrictive
  75requirements, but should work in most cases. Some, albeit outdated,
  76documentation can be found in Documentation/power/swsusp.txt.
  77Alternatively, userspace can do most of the actual suspend to disk work,
  78see userland-swsusp.txt.
  80Once memory state is written to disk, the system may either enter a
  81low-power state (like ACPI S4), or it may simply power down. Powering
  82down offers greater savings, and allows this mechanism to work on any
  83system. However, entering a real low-power state allows the user to
  84trigger wake up events (e.g. pressing a key or opening a laptop lid).
  85 kindly hosted by Redpill Linpro AS, provider of Linux consulting and operations services since 1995.