linux/Documentation/pwm.txt
<<
>>
Prefs
   1Pulse Width Modulation (PWM) interface
   2
   3This provides an overview about the Linux PWM interface
   4
   5PWMs are commonly used for controlling LEDs, fans or vibrators in
   6cell phones. PWMs with a fixed purpose have no need implementing
   7the Linux PWM API (although they could). However, PWMs are often
   8found as discrete devices on SoCs which have no fixed purpose. It's
   9up to the board designer to connect them to LEDs or fans. To provide
  10this kind of flexibility the generic PWM API exists.
  11
  12Identifying PWMs
  13----------------
  14
  15Users of the legacy PWM API use unique IDs to refer to PWM devices.
  16
  17Instead of referring to a PWM device via its unique ID, board setup code
  18should instead register a static mapping that can be used to match PWM
  19consumers to providers, as given in the following example:
  20
  21        static struct pwm_lookup board_pwm_lookup[] = {
  22                PWM_LOOKUP("tegra-pwm", 0, "pwm-backlight", NULL),
  23        };
  24
  25        static void __init board_init(void)
  26        {
  27                ...
  28                pwm_add_table(board_pwm_lookup, ARRAY_SIZE(board_pwm_lookup));
  29                ...
  30        }
  31
  32Using PWMs
  33----------
  34
  35Legacy users can request a PWM device using pwm_request() and free it
  36after usage with pwm_free().
  37
  38New users should use the pwm_get() function and pass to it the consumer
  39device or a consumer name. pwm_put() is used to free the PWM device. Managed
  40variants of these functions, devm_pwm_get() and devm_pwm_put(), also exist.
  41
  42After being requested a PWM has to be configured using:
  43
  44int pwm_config(struct pwm_device *pwm, int duty_ns, int period_ns);
  45
  46To start/stop toggling the PWM output use pwm_enable()/pwm_disable().
  47
  48Using PWMs with the sysfs interface
  49-----------------------------------
  50
  51If CONFIG_SYSFS is enabled in your kernel configuration a simple sysfs
  52interface is provided to use the PWMs from userspace. It is exposed at
  53/sys/class/pwm/. Each probed PWM controller/chip will be exported as
  54pwmchipN, where N is the base of the PWM chip. Inside the directory you
  55will find:
  56
  57npwm - The number of PWM channels this chip supports (read-only).
  58
  59export - Exports a PWM channel for use with sysfs (write-only).
  60
  61unexport - Unexports a PWM channel from sysfs (write-only).
  62
  63The PWM channels are numbered using a per-chip index from 0 to npwm-1.
  64
  65When a PWM channel is exported a pwmX directory will be created in the
  66pwmchipN directory it is associated with, where X is the number of the
  67channel that was exported. The following properties will then be available:
  68
  69period - The total period of the PWM signal (read/write).
  70        Value is in nanoseconds and is the sum of the active and inactive
  71        time of the PWM.
  72
  73duty_cycle - The active time of the PWM signal (read/write).
  74        Value is in nanoseconds and must be less than the period.
  75
  76polarity - Changes the polarity of the PWM signal (read/write).
  77        Writes to this property only work if the PWM chip supports changing
  78        the polarity. The polarity can only be changed if the PWM is not
  79        enabled. Value is the string "normal" or "inversed".
  80
  81enable - Enable/disable the PWM signal (read/write).
  82        0 - disabled
  83        1 - enabled
  84
  85Implementing a PWM driver
  86-------------------------
  87
  88Currently there are two ways to implement pwm drivers. Traditionally
  89there only has been the barebone API meaning that each driver has
  90to implement the pwm_*() functions itself. This means that it's impossible
  91to have multiple PWM drivers in the system. For this reason it's mandatory
  92for new drivers to use the generic PWM framework.
  93
  94A new PWM controller/chip can be added using pwmchip_add() and removed
  95again with pwmchip_remove(). pwmchip_add() takes a filled in struct
  96pwm_chip as argument which provides a description of the PWM chip, the
  97number of PWM devices provider by the chip and the chip-specific
  98implementation of the supported PWM operations to the framework.
  99
 100Locking
 101-------
 102
 103The PWM core list manipulations are protected by a mutex, so pwm_request()
 104and pwm_free() may not be called from an atomic context. Currently the
 105PWM core does not enforce any locking to pwm_enable(), pwm_disable() and
 106pwm_config(), so the calling context is currently driver specific. This
 107is an issue derived from the former barebone API and should be fixed soon.
 108
 109Helpers
 110-------
 111
 112Currently a PWM can only be configured with period_ns and duty_ns. For several
 113use cases freq_hz and duty_percent might be better. Instead of calculating
 114this in your driver please consider adding appropriate helpers to the framework.
 115
lxr.linux.no kindly hosted by Redpill Linpro AS, provider of Linux consulting and operations services since 1995.