linux/drivers/video/Kconfig
<<
>>
Prefs
   1#
   2# Video configuration
   3#
   4
   5menu "Graphics support"
   6        depends on HAS_IOMEM
   7
   8config HAVE_FB_ATMEL
   9        bool
  10
  11config SH_MIPI_DSI
  12        tristate
  13        depends on (SUPERH || ARCH_SHMOBILE) && HAVE_CLK
  14
  15config SH_LCD_MIPI_DSI
  16        bool
  17
  18source "drivers/char/agp/Kconfig"
  19
  20source "drivers/gpu/vga/Kconfig"
  21
  22source "drivers/gpu/drm/Kconfig"
  23
  24source "drivers/gpu/host1x/Kconfig"
  25
  26config VGASTATE
  27       tristate
  28       default n
  29
  30config VIDEO_OUTPUT_CONTROL
  31        tristate "Lowlevel video output switch controls"
  32        help
  33          This framework adds support for low-level control of the video 
  34          output switch.
  35
  36config VIDEOMODE_HELPERS
  37        bool
  38
  39config HDMI
  40        bool
  41
  42menuconfig FB
  43        tristate "Support for frame buffer devices"
  44        ---help---
  45          The frame buffer device provides an abstraction for the graphics
  46          hardware. It represents the frame buffer of some video hardware and
  47          allows application software to access the graphics hardware through
  48          a well-defined interface, so the software doesn't need to know
  49          anything about the low-level (hardware register) stuff.
  50
  51          Frame buffer devices work identically across the different
  52          architectures supported by Linux and make the implementation of
  53          application programs easier and more portable; at this point, an X
  54          server exists which uses the frame buffer device exclusively.
  55          On several non-X86 architectures, the frame buffer device is the
  56          only way to use the graphics hardware.
  57
  58          The device is accessed through special device nodes, usually located
  59          in the /dev directory, i.e. /dev/fb*.
  60
  61          You need an utility program called fbset to make full use of frame
  62          buffer devices. Please read <file:Documentation/fb/framebuffer.txt>
  63          and the Framebuffer-HOWTO at
  64          <http://www.munted.org.uk/programming/Framebuffer-HOWTO-1.3.html> for more
  65          information.
  66
  67          Say Y here and to the driver for your graphics board below if you
  68          are compiling a kernel for a non-x86 architecture.
  69
  70          If you are compiling for the x86 architecture, you can say Y if you
  71          want to play with it, but it is not essential. Please note that
  72          running graphical applications that directly touch the hardware
  73          (e.g. an accelerated X server) and that are not frame buffer
  74          device-aware may cause unexpected results. If unsure, say N.
  75
  76config FIRMWARE_EDID
  77       bool "Enable firmware EDID"
  78       depends on FB
  79       default n
  80       ---help---
  81         This enables access to the EDID transferred from the firmware.
  82         On the i386, this is from the Video BIOS. Enable this if DDC/I2C
  83         transfers do not work for your driver and if you are using
  84         nvidiafb, i810fb or savagefb.
  85
  86         In general, choosing Y for this option is safe.  If you
  87         experience extremely long delays while booting before you get
  88         something on your display, try setting this to N.  Matrox cards in
  89         combination with certain motherboards and monitors are known to
  90         suffer from this problem.
  91
  92config FB_DDC
  93       tristate
  94       depends on FB
  95       select I2C_ALGOBIT
  96       select I2C
  97       default n
  98
  99config FB_BOOT_VESA_SUPPORT
 100        bool
 101        depends on FB
 102        default n
 103        ---help---
 104          If true, at least one selected framebuffer driver can take advantage
 105          of VESA video modes set at an early boot stage via the vga= parameter.
 106
 107config FB_CFB_FILLRECT
 108        tristate
 109        depends on FB
 110        default n
 111        ---help---
 112          Include the cfb_fillrect function for generic software rectangle
 113          filling. This is used by drivers that don't provide their own
 114          (accelerated) version.
 115
 116config FB_CFB_COPYAREA
 117        tristate
 118        depends on FB
 119        default n
 120        ---help---
 121          Include the cfb_copyarea function for generic software area copying.
 122          This is used by drivers that don't provide their own (accelerated)
 123          version.
 124
 125config FB_CFB_IMAGEBLIT
 126        tristate
 127        depends on FB
 128        default n
 129        ---help---
 130          Include the cfb_imageblit function for generic software image
 131          blitting. This is used by drivers that don't provide their own
 132          (accelerated) version.
 133
 134config FB_CFB_REV_PIXELS_IN_BYTE
 135        bool
 136        depends on FB
 137        default n
 138        ---help---
 139          Allow generic frame-buffer functions to work on displays with 1, 2
 140          and 4 bits per pixel depths which has opposite order of pixels in
 141          byte order to bytes in long order.
 142
 143config FB_SYS_FILLRECT
 144        tristate
 145        depends on FB
 146        default n
 147        ---help---
 148          Include the sys_fillrect function for generic software rectangle
 149          filling. This is used by drivers that don't provide their own
 150          (accelerated) version and the framebuffer is in system RAM.
 151
 152config FB_SYS_COPYAREA
 153        tristate
 154        depends on FB
 155        default n
 156        ---help---
 157          Include the sys_copyarea function for generic software area copying.
 158          This is used by drivers that don't provide their own (accelerated)
 159          version and the framebuffer is in system RAM.
 160
 161config FB_SYS_IMAGEBLIT
 162        tristate
 163        depends on FB
 164        default n
 165        ---help---
 166          Include the sys_imageblit function for generic software image
 167          blitting. This is used by drivers that don't provide their own
 168          (accelerated) version and the framebuffer is in system RAM.
 169
 170menuconfig FB_FOREIGN_ENDIAN
 171        bool "Framebuffer foreign endianness support"
 172        depends on FB
 173        ---help---
 174          This menu will let you enable support for the framebuffers with
 175          non-native endianness (e.g. Little-Endian framebuffer on a
 176          Big-Endian machine). Most probably you don't have such hardware,
 177          so it's safe to say "n" here.
 178
 179choice
 180        prompt "Choice endianness support"
 181        depends on FB_FOREIGN_ENDIAN
 182
 183config FB_BOTH_ENDIAN
 184        bool "Support for Big- and Little-Endian framebuffers"
 185
 186config FB_BIG_ENDIAN
 187        bool "Support for Big-Endian framebuffers only"
 188
 189config FB_LITTLE_ENDIAN
 190        bool "Support for Little-Endian framebuffers only"
 191
 192endchoice
 193
 194config FB_SYS_FOPS
 195       tristate
 196       depends on FB
 197       default n
 198
 199config FB_DEFERRED_IO
 200        bool
 201        depends on FB
 202
 203config FB_HECUBA
 204        tristate
 205        depends on FB
 206        depends on FB_DEFERRED_IO
 207
 208config FB_SVGALIB
 209        tristate
 210        depends on FB
 211        default n
 212        ---help---
 213          Common utility functions useful to fbdev drivers of VGA-based
 214          cards.
 215
 216config FB_MACMODES
 217       tristate
 218       depends on FB
 219       default n
 220
 221config FB_BACKLIGHT
 222        bool
 223        depends on FB
 224        select BACKLIGHT_LCD_SUPPORT
 225        select BACKLIGHT_CLASS_DEVICE
 226        default n
 227
 228config FB_MODE_HELPERS
 229        bool "Enable Video Mode Handling Helpers"
 230        depends on FB
 231        default n
 232        ---help---
 233          This enables functions for handling video modes using the
 234          Generalized Timing Formula and the EDID parser. A few drivers rely
 235          on this feature such as the radeonfb, rivafb, and the i810fb. If
 236          your driver does not take advantage of this feature, choosing Y will
 237          just increase the kernel size by about 5K.
 238
 239config FB_TILEBLITTING
 240       bool "Enable Tile Blitting Support"
 241       depends on FB
 242       default n
 243       ---help---
 244         This enables tile blitting.  Tile blitting is a drawing technique
 245         where the screen is divided into rectangular sections (tiles), whereas
 246         the standard blitting divides the screen into pixels. Because the
 247         default drawing element is a tile, drawing functions will be passed
 248         parameters in terms of number of tiles instead of number of pixels.
 249         For example, to draw a single character, instead of using bitmaps,
 250         an index to an array of bitmaps will be used.  To clear or move a
 251         rectangular section of a screen, the rectangle will be described in
 252         terms of number of tiles in the x- and y-axis.
 253
 254         This is particularly important to one driver, matroxfb.  If
 255         unsure, say N.
 256
 257comment "Frame buffer hardware drivers"
 258        depends on FB
 259
 260config FB_GRVGA
 261        tristate "Aeroflex Gaisler framebuffer support"
 262        depends on FB && SPARC
 263        select FB_CFB_FILLRECT
 264        select FB_CFB_COPYAREA
 265        select FB_CFB_IMAGEBLIT
 266        ---help---
 267        This enables support for the SVGACTRL framebuffer in the GRLIB IP library from Aeroflex Gaisler.
 268
 269config FB_CIRRUS
 270        tristate "Cirrus Logic support"
 271        depends on FB && (ZORRO || PCI)
 272        select FB_CFB_FILLRECT
 273        select FB_CFB_COPYAREA
 274        select FB_CFB_IMAGEBLIT
 275        ---help---
 276          This enables support for Cirrus Logic GD542x/543x based boards on
 277          Amiga: SD64, Piccolo, Picasso II/II+, Picasso IV, or EGS Spectrum.
 278
 279          If you have a PCI-based system, this enables support for these
 280          chips: GD-543x, GD-544x, GD-5480.
 281
 282          Please read the file <file:Documentation/fb/cirrusfb.txt>.
 283
 284          Say N unless you have such a graphics board or plan to get one
 285          before you next recompile the kernel.
 286
 287config FB_PM2
 288        tristate "Permedia2 support"
 289        depends on FB && ((AMIGA && BROKEN) || PCI)
 290        select FB_CFB_FILLRECT
 291        select FB_CFB_COPYAREA
 292        select FB_CFB_IMAGEBLIT
 293        help
 294          This is the frame buffer device driver for cards based on
 295          the 3D Labs Permedia, Permedia 2 and Permedia 2V chips.
 296          The driver was tested on the following cards:
 297                Diamond FireGL 1000 PRO AGP
 298                ELSA Gloria Synergy PCI
 299                Appian Jeronimo PRO (both heads) PCI
 300                3DLabs Oxygen ACX aka EONtronics Picasso P2 PCI
 301                Techsource Raptor GFX-8P (aka Sun PGX-32) on SPARC
 302                ASK Graphic Blaster Exxtreme AGP
 303
 304          To compile this driver as a module, choose M here: the
 305          module will be called pm2fb.
 306
 307config FB_PM2_FIFO_DISCONNECT
 308        bool "enable FIFO disconnect feature"
 309        depends on FB_PM2 && PCI
 310        help
 311          Support the Permedia2 FIFO disconnect feature.
 312
 313config FB_ARMCLCD
 314        tristate "ARM PrimeCell PL110 support"
 315        depends on FB && ARM && ARM_AMBA
 316        select FB_CFB_FILLRECT
 317        select FB_CFB_COPYAREA
 318        select FB_CFB_IMAGEBLIT
 319        help
 320          This framebuffer device driver is for the ARM PrimeCell PL110
 321          Colour LCD controller.  ARM PrimeCells provide the building
 322          blocks for System on a Chip devices.
 323
 324          If you want to compile this as a module (=code which can be
 325          inserted into and removed from the running kernel), say M
 326          here and read <file:Documentation/kbuild/modules.txt>.  The module
 327          will be called amba-clcd.
 328
 329config FB_ACORN
 330        bool "Acorn VIDC support"
 331        depends on (FB = y) && ARM && ARCH_ACORN
 332        select FB_CFB_FILLRECT
 333        select FB_CFB_COPYAREA
 334        select FB_CFB_IMAGEBLIT
 335        help
 336          This is the frame buffer device driver for the Acorn VIDC graphics
 337          hardware found in Acorn RISC PCs and other ARM-based machines.  If
 338          unsure, say N.
 339
 340config FB_CLPS711X
 341        bool "CLPS711X LCD support"
 342        depends on (FB = y) && ARM && ARCH_CLPS711X
 343        select FB_CFB_FILLRECT
 344        select FB_CFB_COPYAREA
 345        select FB_CFB_IMAGEBLIT
 346        help
 347          Say Y to enable the Framebuffer driver for the CLPS7111 and
 348          EP7212 processors.
 349
 350config FB_SA1100
 351        bool "SA-1100 LCD support"
 352        depends on (FB = y) && ARM && ARCH_SA1100
 353        select FB_CFB_FILLRECT
 354        select FB_CFB_COPYAREA
 355        select FB_CFB_IMAGEBLIT
 356        help
 357          This is a framebuffer device for the SA-1100 LCD Controller.
 358          See <http://www.linux-fbdev.org/> for information on framebuffer
 359          devices.
 360
 361          If you plan to use the LCD display with your SA-1100 system, say
 362          Y here.
 363
 364config FB_IMX
 365        tristate "Freescale i.MX1/21/25/27 LCD support"
 366        depends on FB && IMX_HAVE_PLATFORM_IMX_FB
 367        select FB_CFB_FILLRECT
 368        select FB_CFB_COPYAREA
 369        select FB_CFB_IMAGEBLIT
 370
 371config FB_CYBER2000
 372        tristate "CyberPro 2000/2010/5000 support"
 373        depends on FB && PCI && (BROKEN || !SPARC64)
 374        select FB_CFB_FILLRECT
 375        select FB_CFB_COPYAREA
 376        select FB_CFB_IMAGEBLIT
 377        help
 378          This enables support for the Integraphics CyberPro 20x0 and 5000
 379          VGA chips used in the Rebel.com Netwinder and other machines.
 380          Say Y if you have a NetWinder or a graphics card containing this
 381          device, otherwise say N.
 382
 383config FB_CYBER2000_DDC
 384        bool "DDC for CyberPro support"
 385        depends on FB_CYBER2000
 386        select FB_DDC
 387        default y
 388        help
 389          Say Y here if you want DDC support for your CyberPro graphics
 390          card. This is only I2C bus support, driver does not use EDID.
 391
 392config FB_CYBER2000_I2C
 393        bool "CyberPro 2000/2010/5000 I2C support"
 394        depends on FB_CYBER2000 && I2C && ARCH_NETWINDER
 395        select I2C_ALGOBIT
 396        help
 397          Enable support for the I2C video decoder interface on the
 398          Integraphics CyberPro 20x0 and 5000 VGA chips.  This is used
 399          on the Netwinder machines for the SAA7111 video capture.
 400
 401config FB_APOLLO
 402        bool
 403        depends on (FB = y) && APOLLO
 404        default y
 405        select FB_CFB_FILLRECT
 406        select FB_CFB_IMAGEBLIT
 407
 408config FB_Q40
 409        bool
 410        depends on (FB = y) && Q40
 411        default y
 412        select FB_CFB_FILLRECT
 413        select FB_CFB_COPYAREA
 414        select FB_CFB_IMAGEBLIT
 415
 416config FB_AMIGA
 417        tristate "Amiga native chipset support"
 418        depends on FB && AMIGA
 419        help
 420          This is the frame buffer device driver for the builtin graphics
 421          chipset found in Amigas.
 422
 423          To compile this driver as a module, choose M here: the
 424          module will be called amifb.
 425
 426config FB_AMIGA_OCS
 427        bool "Amiga OCS chipset support"
 428        depends on FB_AMIGA
 429        help
 430          This enables support for the original Agnus and Denise video chips,
 431          found in the Amiga 1000 and most A500's and A2000's. If you intend
 432          to run Linux on any of these systems, say Y; otherwise say N.
 433
 434config FB_AMIGA_ECS
 435        bool "Amiga ECS chipset support"
 436        depends on FB_AMIGA
 437        help
 438          This enables support for the Enhanced Chip Set, found in later
 439          A500's, later A2000's, the A600, the A3000, the A3000T and CDTV. If
 440          you intend to run Linux on any of these systems, say Y; otherwise
 441          say N.
 442
 443config FB_AMIGA_AGA
 444        bool "Amiga AGA chipset support"
 445        depends on FB_AMIGA
 446        help
 447          This enables support for the Advanced Graphics Architecture (also
 448          known as the AGA or AA) Chip Set, found in the A1200, A4000, A4000T
 449          and CD32. If you intend to run Linux on any of these systems, say Y;
 450          otherwise say N.
 451
 452config FB_FM2
 453        bool "Amiga FrameMaster II/Rainbow II support"
 454        depends on (FB = y) && ZORRO
 455        select FB_CFB_FILLRECT
 456        select FB_CFB_COPYAREA
 457        select FB_CFB_IMAGEBLIT
 458        help
 459          This is the frame buffer device driver for the Amiga FrameMaster
 460          card from BSC (exhibited 1992 but not shipped as a CBM product).
 461
 462config FB_ARC
 463        tristate "Arc Monochrome LCD board support"
 464        depends on FB && X86
 465        select FB_SYS_FILLRECT
 466        select FB_SYS_COPYAREA
 467        select FB_SYS_IMAGEBLIT
 468        select FB_SYS_FOPS
 469        help
 470          This enables support for the Arc Monochrome LCD board. The board
 471          is based on the KS-108 lcd controller and is typically a matrix
 472          of 2*n chips. This driver was tested with a 128x64 panel. This
 473          driver supports it for use with x86 SBCs through a 16 bit GPIO
 474          interface (8 bit data, 8 bit control). If you anticipate using
 475          this driver, say Y or M; otherwise say N. You must specify the
 476          GPIO IO address to be used for setting control and data.
 477
 478config FB_ATARI
 479        bool "Atari native chipset support"
 480        depends on (FB = y) && ATARI
 481        select FB_CFB_FILLRECT
 482        select FB_CFB_COPYAREA
 483        select FB_CFB_IMAGEBLIT
 484        help
 485          This is the frame buffer device driver for the builtin graphics
 486          chipset found in Ataris.
 487
 488config FB_OF
 489        bool "Open Firmware frame buffer device support"
 490        depends on (FB = y) && (PPC64 || PPC_OF) && (!PPC_PSERIES || PCI)
 491        select FB_CFB_FILLRECT
 492        select FB_CFB_COPYAREA
 493        select FB_CFB_IMAGEBLIT
 494        select FB_MACMODES
 495        help
 496          Say Y if you want support with Open Firmware for your graphics
 497          board.
 498
 499config FB_CONTROL
 500        bool "Apple \"control\" display support"
 501        depends on (FB = y) && PPC_PMAC && PPC32
 502        select FB_CFB_FILLRECT
 503        select FB_CFB_COPYAREA
 504        select FB_CFB_IMAGEBLIT
 505        select FB_MACMODES
 506        help
 507          This driver supports a frame buffer for the graphics adapter in the
 508          Power Macintosh 7300 and others.
 509
 510config FB_PLATINUM
 511        bool "Apple \"platinum\" display support"
 512        depends on (FB = y) && PPC_PMAC && PPC32
 513        select FB_CFB_FILLRECT
 514        select FB_CFB_COPYAREA
 515        select FB_CFB_IMAGEBLIT
 516        select FB_MACMODES
 517        help
 518          This driver supports a frame buffer for the "platinum" graphics
 519          adapter in some Power Macintoshes.
 520
 521config FB_VALKYRIE
 522        bool "Apple \"valkyrie\" display support"
 523        depends on (FB = y) && (MAC || (PPC_PMAC && PPC32))
 524        select FB_CFB_FILLRECT
 525        select FB_CFB_COPYAREA
 526        select FB_CFB_IMAGEBLIT
 527        select FB_MACMODES
 528        help
 529          This driver supports a frame buffer for the "valkyrie" graphics
 530          adapter in some Power Macintoshes.
 531
 532config FB_CT65550
 533        bool "Chips 65550 display support"
 534        depends on (FB = y) && PPC32 && PCI
 535        select FB_CFB_FILLRECT
 536        select FB_CFB_COPYAREA
 537        select FB_CFB_IMAGEBLIT
 538        help
 539          This is the frame buffer device driver for the Chips & Technologies
 540          65550 graphics chip in PowerBooks.
 541
 542config FB_ASILIANT
 543        bool "Asiliant (Chips) 69000 display support"
 544        depends on (FB = y) && PCI
 545        select FB_CFB_FILLRECT
 546        select FB_CFB_COPYAREA
 547        select FB_CFB_IMAGEBLIT
 548        help
 549          This is the frame buffer device driver for the Asiliant 69030 chipset
 550
 551config FB_IMSTT
 552        bool "IMS Twin Turbo display support"
 553        depends on (FB = y) && PCI
 554        select FB_CFB_IMAGEBLIT
 555        select FB_MACMODES if PPC
 556        help
 557          The IMS Twin Turbo is a PCI-based frame buffer card bundled with
 558          many Macintosh and compatible computers.
 559
 560config FB_VGA16
 561        tristate "VGA 16-color graphics support"
 562        depends on FB && (X86 || PPC)
 563        select FB_CFB_FILLRECT
 564        select FB_CFB_COPYAREA
 565        select FB_CFB_IMAGEBLIT
 566        select VGASTATE
 567        select FONT_8x16 if FRAMEBUFFER_CONSOLE
 568        help
 569          This is the frame buffer device driver for VGA 16 color graphic
 570          cards. Say Y if you have such a card.
 571
 572          To compile this driver as a module, choose M here: the
 573          module will be called vga16fb.
 574
 575config FB_BF54X_LQ043
 576        tristate "SHARP LQ043 TFT LCD (BF548 EZKIT)"
 577        depends on FB && (BF54x) && !BF542
 578        select FB_CFB_FILLRECT
 579        select FB_CFB_COPYAREA
 580        select FB_CFB_IMAGEBLIT
 581        help
 582         This is the framebuffer device driver for a SHARP LQ043T1DG01 TFT LCD
 583
 584config FB_BFIN_T350MCQB
 585        tristate "Varitronix COG-T350MCQB TFT LCD display (BF527 EZKIT)"
 586        depends on FB && BLACKFIN
 587        select BFIN_GPTIMERS
 588        select FB_CFB_FILLRECT
 589        select FB_CFB_COPYAREA
 590        select FB_CFB_IMAGEBLIT
 591        help
 592         This is the framebuffer device driver for a Varitronix VL-PS-COG-T350MCQB-01 display TFT LCD
 593         This display is a QVGA 320x240 24-bit RGB display interfaced by an 8-bit wide PPI
 594         It uses PPI[0..7] PPI_FS1, PPI_FS2 and PPI_CLK.
 595
 596config FB_BFIN_LQ035Q1
 597        tristate "SHARP LQ035Q1DH02 TFT LCD"
 598        depends on FB && BLACKFIN && SPI
 599        select FB_CFB_FILLRECT
 600        select FB_CFB_COPYAREA
 601        select FB_CFB_IMAGEBLIT
 602        select BFIN_GPTIMERS
 603        help
 604          This is the framebuffer device driver for a SHARP LQ035Q1DH02 TFT display found on
 605          the Blackfin Landscape LCD EZ-Extender Card.
 606          This display is a QVGA 320x240 18-bit RGB display interfaced by an 16-bit wide PPI
 607          It uses PPI[0..15] PPI_FS1, PPI_FS2 and PPI_CLK.
 608
 609          To compile this driver as a module, choose M here: the
 610          module will be called bfin-lq035q1-fb.
 611
 612config FB_BF537_LQ035
 613        tristate "SHARP LQ035 TFT LCD (BF537 STAMP)"
 614        depends on FB && (BF534 || BF536 || BF537) && I2C_BLACKFIN_TWI
 615        select FB_CFB_FILLRECT
 616        select FB_CFB_COPYAREA
 617        select FB_CFB_IMAGEBLIT
 618        select BFIN_GPTIMERS
 619        help
 620          This is the framebuffer device for a SHARP LQ035Q7DB03 TFT LCD
 621          attached to a BF537.
 622
 623          To compile this driver as a module, choose M here: the
 624          module will be called bf537-lq035.
 625
 626config FB_BFIN_7393
 627        tristate "Blackfin ADV7393 Video encoder"
 628        depends on FB && BLACKFIN
 629        select I2C
 630        select FB_CFB_FILLRECT
 631        select FB_CFB_COPYAREA
 632        select FB_CFB_IMAGEBLIT
 633        help
 634          This is the framebuffer device for a ADV7393 video encoder
 635          attached to a Blackfin on the PPI port.
 636          If your Blackfin board has a ADV7393 select Y.
 637
 638          To compile this driver as a module, choose M here: the
 639          module will be called bfin_adv7393fb.
 640
 641choice
 642        prompt  "Video mode support"
 643        depends on FB_BFIN_7393
 644        default NTSC
 645
 646config NTSC
 647        bool 'NTSC 720x480'
 648
 649config PAL
 650        bool 'PAL 720x576'
 651
 652config NTSC_640x480
 653        bool 'NTSC 640x480 (Experimental)'
 654
 655config PAL_640x480
 656        bool 'PAL 640x480 (Experimental)'
 657
 658config NTSC_YCBCR
 659        bool 'NTSC 720x480 YCbCR input'
 660
 661config PAL_YCBCR
 662        bool 'PAL 720x576 YCbCR input'
 663
 664endchoice
 665
 666choice
 667        prompt  "Size of ADV7393 frame buffer memory Single/Double Size"
 668        depends on (FB_BFIN_7393)
 669        default ADV7393_1XMEM
 670
 671config ADV7393_1XMEM
 672        bool 'Single'
 673
 674config ADV7393_2XMEM
 675        bool 'Double'
 676endchoice
 677
 678config FB_STI
 679        tristate "HP STI frame buffer device support"
 680        depends on FB && PARISC
 681        select FB_CFB_FILLRECT
 682        select FB_CFB_COPYAREA
 683        select FB_CFB_IMAGEBLIT
 684        select STI_CONSOLE
 685        select VT
 686        default y
 687        ---help---
 688          STI refers to the HP "Standard Text Interface" which is a set of
 689          BIOS routines contained in a ROM chip in HP PA-RISC based machines.
 690          Enabling this option will implement the linux framebuffer device
 691          using calls to the STI BIOS routines for initialisation.
 692        
 693          If you enable this option, you will get a planar framebuffer device
 694          /dev/fb which will work on the most common HP graphic cards of the
 695          NGLE family, including the artist chips (in the 7xx and Bxxx series),
 696          HCRX, HCRX24, CRX, CRX24 and VisEG series.
 697
 698          It is safe to enable this option, so you should probably say "Y".
 699
 700config FB_MAC
 701        bool "Generic Macintosh display support"
 702        depends on (FB = y) && MAC
 703        select FB_CFB_FILLRECT
 704        select FB_CFB_COPYAREA
 705        select FB_CFB_IMAGEBLIT
 706        select FB_MACMODES
 707
 708config FB_HP300
 709        bool
 710        depends on (FB = y) && DIO
 711        select FB_CFB_IMAGEBLIT
 712        default y
 713
 714config FB_TGA
 715        tristate "TGA/SFB+ framebuffer support"
 716        depends on FB && (ALPHA || TC)
 717        select FB_CFB_FILLRECT
 718        select FB_CFB_COPYAREA
 719        select FB_CFB_IMAGEBLIT
 720        select BITREVERSE
 721        ---help---
 722          This is the frame buffer device driver for generic TGA and SFB+
 723          graphic cards.  These include DEC ZLXp-E1, -E2 and -E3 PCI cards,
 724          also known as PBXGA-A, -B and -C, and DEC ZLX-E1, -E2 and -E3
 725          TURBOchannel cards, also known as PMAGD-A, -B and -C.
 726
 727          Due to hardware limitations ZLX-E2 and E3 cards are not supported
 728          for DECstation 5000/200 systems.  Additionally due to firmware
 729          limitations these cards may cause troubles with booting DECstation
 730          5000/240 and /260 systems, but are fully supported under Linux if
 731          you manage to get it going. ;-)
 732
 733          Say Y if you have one of those.
 734
 735config FB_UVESA
 736        tristate "Userspace VESA VGA graphics support"
 737        depends on FB && CONNECTOR
 738        select FB_CFB_FILLRECT
 739        select FB_CFB_COPYAREA
 740        select FB_CFB_IMAGEBLIT
 741        select FB_MODE_HELPERS
 742        help
 743          This is the frame buffer driver for generic VBE 2.0 compliant
 744          graphic cards. It can also take advantage of VBE 3.0 features,
 745          such as refresh rate adjustment.
 746
 747          This driver generally provides more features than vesafb but
 748          requires a userspace helper application called 'v86d'. See
 749          <file:Documentation/fb/uvesafb.txt> for more information.
 750
 751          If unsure, say N.
 752
 753config FB_VESA
 754        bool "VESA VGA graphics support"
 755        depends on (FB = y) && X86
 756        select FB_CFB_FILLRECT
 757        select FB_CFB_COPYAREA
 758        select FB_CFB_IMAGEBLIT
 759        select FB_BOOT_VESA_SUPPORT
 760        help
 761          This is the frame buffer device driver for generic VESA 2.0
 762          compliant graphic cards. The older VESA 1.2 cards are not supported.
 763          You will get a boot time penguin logo at no additional cost. Please
 764          read <file:Documentation/fb/vesafb.txt>. If unsure, say Y.
 765
 766config FB_EFI
 767        bool "EFI-based Framebuffer Support"
 768        depends on (FB = y) && X86 && EFI
 769        select FB_CFB_FILLRECT
 770        select FB_CFB_COPYAREA
 771        select FB_CFB_IMAGEBLIT
 772        help
 773          This is the EFI frame buffer device driver. If the firmware on
 774          your platform is EFI 1.10 or UEFI 2.0, select Y to add support for
 775          using the EFI framebuffer as your console.
 776
 777config FB_N411
 778       tristate "N411 Apollo/Hecuba devkit support"
 779       depends on FB && X86 && MMU
 780       select FB_SYS_FILLRECT
 781       select FB_SYS_COPYAREA
 782       select FB_SYS_IMAGEBLIT
 783       select FB_SYS_FOPS
 784       select FB_DEFERRED_IO
 785       select FB_HECUBA
 786       help
 787         This enables support for the Apollo display controller in its
 788         Hecuba form using the n411 devkit.
 789
 790config FB_HGA
 791        tristate "Hercules mono graphics support"
 792        depends on FB && X86
 793        help
 794          Say Y here if you have a Hercules mono graphics card.
 795
 796          To compile this driver as a module, choose M here: the
 797          module will be called hgafb.
 798
 799          As this card technology is at least 25 years old,
 800          most people will answer N here.
 801
 802config FB_SGIVW
 803        tristate "SGI Visual Workstation framebuffer support"
 804        depends on FB && X86_VISWS
 805        select FB_CFB_FILLRECT
 806        select FB_CFB_COPYAREA
 807        select FB_CFB_IMAGEBLIT
 808        help
 809          SGI Visual Workstation support for framebuffer graphics.
 810
 811config FB_GBE
 812        bool "SGI Graphics Backend frame buffer support"
 813        depends on (FB = y) && (SGI_IP32 || X86_VISWS)
 814        select FB_CFB_FILLRECT
 815        select FB_CFB_COPYAREA
 816        select FB_CFB_IMAGEBLIT
 817        help
 818          This is the frame buffer device driver for SGI Graphics Backend.
 819          This chip is used in SGI O2 and Visual Workstation 320/540.
 820
 821config FB_GBE_MEM
 822        int "Video memory size in MB"
 823        depends on FB_GBE
 824        default 4
 825        help
 826          This is the amount of memory reserved for the framebuffer,
 827          which can be any value between 1MB and 8MB.
 828
 829config FB_SBUS
 830        bool "SBUS and UPA framebuffers"
 831        depends on (FB = y) && SPARC
 832        help
 833          Say Y if you want support for SBUS or UPA based frame buffer device.
 834
 835config FB_BW2
 836        bool "BWtwo support"
 837        depends on (FB = y) && (SPARC && FB_SBUS)
 838        select FB_CFB_FILLRECT
 839        select FB_CFB_COPYAREA
 840        select FB_CFB_IMAGEBLIT
 841        help
 842          This is the frame buffer device driver for the BWtwo frame buffer.
 843
 844config FB_CG3
 845        bool "CGthree support"
 846        depends on (FB = y) && (SPARC && FB_SBUS)
 847        select FB_CFB_FILLRECT
 848        select FB_CFB_COPYAREA
 849        select FB_CFB_IMAGEBLIT
 850        help
 851          This is the frame buffer device driver for the CGthree frame buffer.
 852
 853config FB_CG6
 854        bool "CGsix (GX,TurboGX) support"
 855        depends on (FB = y) && (SPARC && FB_SBUS)
 856        select FB_CFB_COPYAREA
 857        select FB_CFB_IMAGEBLIT
 858        help
 859          This is the frame buffer device driver for the CGsix (GX, TurboGX)
 860          frame buffer.
 861
 862config FB_FFB
 863        bool "Creator/Creator3D/Elite3D support"
 864        depends on FB_SBUS && SPARC64
 865        select FB_CFB_COPYAREA
 866        select FB_CFB_IMAGEBLIT
 867        help
 868          This is the frame buffer device driver for the Creator, Creator3D,
 869          and Elite3D graphics boards.
 870
 871config FB_TCX
 872        bool "TCX (SS4/SS5 only) support"
 873        depends on FB_SBUS
 874        select FB_CFB_FILLRECT
 875        select FB_CFB_COPYAREA
 876        select FB_CFB_IMAGEBLIT
 877        help
 878          This is the frame buffer device driver for the TCX 24/8bit frame
 879          buffer.
 880
 881config FB_CG14
 882        bool "CGfourteen (SX) support"
 883        depends on FB_SBUS
 884        select FB_CFB_FILLRECT
 885        select FB_CFB_COPYAREA
 886        select FB_CFB_IMAGEBLIT
 887        help
 888          This is the frame buffer device driver for the CGfourteen frame
 889          buffer on Desktop SPARCsystems with the SX graphics option.
 890
 891config FB_P9100
 892        bool "P9100 (Sparcbook 3 only) support"
 893        depends on FB_SBUS
 894        select FB_CFB_FILLRECT
 895        select FB_CFB_COPYAREA
 896        select FB_CFB_IMAGEBLIT
 897        help
 898          This is the frame buffer device driver for the P9100 card
 899          supported on Sparcbook 3 machines.
 900
 901config FB_LEO
 902        bool "Leo (ZX) support"
 903        depends on FB_SBUS
 904        select FB_CFB_FILLRECT
 905        select FB_CFB_COPYAREA
 906        select FB_CFB_IMAGEBLIT
 907        help
 908          This is the frame buffer device driver for the SBUS-based Sun ZX
 909          (leo) frame buffer cards.
 910
 911config FB_IGA
 912        bool "IGA 168x display support"
 913        depends on (FB = y) && SPARC32
 914        select FB_CFB_FILLRECT
 915        select FB_CFB_COPYAREA
 916        select FB_CFB_IMAGEBLIT
 917        help
 918          This is the framebuffer device for the INTERGRAPHICS 1680 and
 919          successor frame buffer cards.
 920
 921config FB_XVR500
 922        bool "Sun XVR-500 3DLABS Wildcat support"
 923        depends on (FB = y) && PCI && SPARC64
 924        select FB_CFB_FILLRECT
 925        select FB_CFB_COPYAREA
 926        select FB_CFB_IMAGEBLIT
 927        help
 928          This is the framebuffer device for the Sun XVR-500 and similar
 929          graphics cards based upon the 3DLABS Wildcat chipset.  The driver
 930          only works on sparc64 systems where the system firmware has
 931          mostly initialized the card already.  It is treated as a
 932          completely dumb framebuffer device.
 933
 934config FB_XVR2500
 935        bool "Sun XVR-2500 3DLABS Wildcat support"
 936        depends on (FB = y) && PCI && SPARC64
 937        select FB_CFB_FILLRECT
 938        select FB_CFB_COPYAREA
 939        select FB_CFB_IMAGEBLIT
 940        help
 941          This is the framebuffer device for the Sun XVR-2500 and similar
 942          graphics cards based upon the 3DLABS Wildcat chipset.  The driver
 943          only works on sparc64 systems where the system firmware has
 944          mostly initialized the card already.  It is treated as a
 945          completely dumb framebuffer device.
 946
 947config FB_XVR1000
 948        bool "Sun XVR-1000 support"
 949        depends on (FB = y) && SPARC64
 950        select FB_CFB_FILLRECT
 951        select FB_CFB_COPYAREA
 952        select FB_CFB_IMAGEBLIT
 953        help
 954          This is the framebuffer device for the Sun XVR-1000 and similar
 955          graphics cards.  The driver only works on sparc64 systems where
 956          the system firmware has mostly initialized the card already.  It
 957          is treated as a completely dumb framebuffer device.
 958
 959config FB_PVR2
 960        tristate "NEC PowerVR 2 display support"
 961        depends on FB && SH_DREAMCAST
 962        select FB_CFB_FILLRECT
 963        select FB_CFB_COPYAREA
 964        select FB_CFB_IMAGEBLIT
 965        ---help---
 966          Say Y here if you have a PowerVR 2 card in your box.  If you plan to
 967          run linux on your Dreamcast, you will have to say Y here.
 968          This driver may or may not work on other PowerVR 2 cards, but is
 969          totally untested.  Use at your own risk.  If unsure, say N.
 970
 971          To compile this driver as a module, choose M here: the
 972          module will be called pvr2fb.
 973
 974          You can pass several parameters to the driver at boot time or at
 975          module load time.  The parameters look like "video=pvr2:XXX", where
 976          the meaning of XXX can be found at the end of the main source file
 977          (<file:drivers/video/pvr2fb.c>). Please see the file
 978          <file:Documentation/fb/pvr2fb.txt>.
 979
 980config FB_S1D13XXX
 981        tristate "Epson S1D13XXX framebuffer support"
 982        depends on FB
 983        select FB_CFB_FILLRECT
 984        select FB_CFB_COPYAREA
 985        select FB_CFB_IMAGEBLIT
 986        help
 987          Support for S1D13XXX framebuffer device family (currently only
 988          working with S1D13806). Product specs at
 989          <http://vdc.epson.com/>
 990
 991config FB_ATMEL
 992        tristate "AT91/AT32 LCD Controller support"
 993        depends on FB && HAVE_FB_ATMEL
 994        select FB_CFB_FILLRECT
 995        select FB_CFB_COPYAREA
 996        select FB_CFB_IMAGEBLIT
 997        help
 998          This enables support for the AT91/AT32 LCD Controller.
 999
1000config FB_INTSRAM
1001        bool "Frame Buffer in internal SRAM"
1002        depends on FB_ATMEL && ARCH_AT91SAM9261
1003        help
1004          Say Y if you want to map Frame Buffer in internal SRAM. Say N if you want
1005          to let frame buffer in external SDRAM.
1006
1007config FB_ATMEL_STN
1008        bool "Use a STN display with AT91/AT32 LCD Controller"
1009        depends on FB_ATMEL && (MACH_AT91SAM9261EK || MACH_AT91SAM9G10EK)
1010        default n
1011        help
1012          Say Y if you want to connect a STN LCD display to the AT91/AT32 LCD
1013          Controller. Say N if you want to connect a TFT.
1014
1015          If unsure, say N.
1016
1017config FB_NVIDIA
1018        tristate "nVidia Framebuffer Support"
1019        depends on FB && PCI
1020        select FB_BACKLIGHT if FB_NVIDIA_BACKLIGHT
1021        select FB_MODE_HELPERS
1022        select FB_CFB_FILLRECT
1023        select FB_CFB_COPYAREA
1024        select FB_CFB_IMAGEBLIT
1025        select BITREVERSE
1026        select VGASTATE
1027        help
1028          This driver supports graphics boards with the nVidia chips, TNT
1029          and newer. For very old chipsets, such as the RIVA128, then use
1030          the rivafb.
1031          Say Y if you have such a graphics board.
1032
1033          To compile this driver as a module, choose M here: the
1034          module will be called nvidiafb.
1035
1036config FB_NVIDIA_I2C
1037       bool "Enable DDC Support"
1038       depends on FB_NVIDIA
1039       select FB_DDC
1040       help
1041          This enables I2C support for nVidia Chipsets.  This is used
1042          only for getting EDID information from the attached display
1043          allowing for robust video mode handling and switching.
1044
1045          Because fbdev-2.6 requires that drivers must be able to
1046          independently validate video mode parameters, you should say Y
1047          here.
1048
1049config FB_NVIDIA_DEBUG
1050        bool "Lots of debug output"
1051        depends on FB_NVIDIA
1052        default n
1053        help
1054          Say Y here if you want the nVidia driver to output all sorts
1055          of debugging information to provide to the maintainer when
1056          something goes wrong.
1057
1058config FB_NVIDIA_BACKLIGHT
1059        bool "Support for backlight control"
1060        depends on FB_NVIDIA
1061        default y
1062        help
1063          Say Y here if you want to control the backlight of your display.
1064
1065config FB_RIVA
1066        tristate "nVidia Riva support"
1067        depends on FB && PCI
1068        select FB_BACKLIGHT if FB_RIVA_BACKLIGHT
1069        select FB_MODE_HELPERS
1070        select FB_CFB_FILLRECT
1071        select FB_CFB_COPYAREA
1072        select FB_CFB_IMAGEBLIT
1073        select BITREVERSE
1074        select VGASTATE
1075        help
1076          This driver supports graphics boards with the nVidia Riva/Geforce
1077          chips.
1078          Say Y if you have such a graphics board.
1079
1080          To compile this driver as a module, choose M here: the
1081          module will be called rivafb.
1082
1083config FB_RIVA_I2C
1084       bool "Enable DDC Support"
1085       depends on FB_RIVA
1086       select FB_DDC
1087       help
1088          This enables I2C support for nVidia Chipsets.  This is used
1089          only for getting EDID information from the attached display
1090          allowing for robust video mode handling and switching.
1091
1092          Because fbdev-2.6 requires that drivers must be able to
1093          independently validate video mode parameters, you should say Y
1094          here.
1095
1096config FB_RIVA_DEBUG
1097        bool "Lots of debug output"
1098        depends on FB_RIVA
1099        default n
1100        help
1101          Say Y here if you want the Riva driver to output all sorts
1102          of debugging information to provide to the maintainer when
1103          something goes wrong.
1104
1105config FB_RIVA_BACKLIGHT
1106        bool "Support for backlight control"
1107        depends on FB_RIVA
1108        default y
1109        help
1110          Say Y here if you want to control the backlight of your display.
1111
1112config FB_I740
1113        tristate "Intel740 support"
1114        depends on FB && PCI
1115        select FB_MODE_HELPERS
1116        select FB_CFB_FILLRECT
1117        select FB_CFB_COPYAREA
1118        select FB_CFB_IMAGEBLIT
1119        select VGASTATE
1120        select FB_DDC
1121        help
1122          This driver supports graphics cards based on Intel740 chip.
1123
1124config FB_I810
1125        tristate "Intel 810/815 support"
1126        depends on FB && PCI && X86_32 && AGP_INTEL
1127        select FB_MODE_HELPERS
1128        select FB_CFB_FILLRECT
1129        select FB_CFB_COPYAREA
1130        select FB_CFB_IMAGEBLIT
1131        select VGASTATE
1132        help
1133          This driver supports the on-board graphics built in to the Intel 810 
1134          and 815 chipsets.  Say Y if you have and plan to use such a board.
1135
1136          To compile this driver as a module, choose M here: the
1137          module will be called i810fb.
1138
1139          For more information, please read 
1140          <file:Documentation/fb/intel810.txt>
1141
1142config FB_I810_GTF
1143        bool "use VESA Generalized Timing Formula"
1144        depends on FB_I810
1145        help
1146          If you say Y, then the VESA standard, Generalized Timing Formula 
1147          or GTF, will be used to calculate the required video timing values
1148          per video mode.  Since the GTF allows nondiscrete timings 
1149          (nondiscrete being a range of values as opposed to discrete being a
1150          set of values), you'll be able to use any combination of horizontal 
1151          and vertical resolutions, and vertical refresh rates without having
1152          to specify your own timing parameters.  This is especially useful
1153          to maximize the performance of an aging display, or if you just 
1154          have a display with nonstandard dimensions. A VESA compliant 
1155          monitor is recommended, but can still work with non-compliant ones.
1156          If you need or want this, then select this option. The timings may 
1157          not be compliant with Intel's recommended values. Use at your own 
1158          risk.
1159
1160          If you say N, the driver will revert to discrete video timings 
1161          using a set recommended by Intel in their documentation.
1162  
1163          If unsure, say N.
1164
1165config FB_I810_I2C
1166        bool "Enable DDC Support"
1167        depends on FB_I810 && FB_I810_GTF
1168        select FB_DDC
1169        help
1170
1171config FB_LE80578
1172        tristate "Intel LE80578 (Vermilion) support"
1173        depends on FB && PCI && X86
1174        select FB_MODE_HELPERS
1175        select FB_CFB_FILLRECT
1176        select FB_CFB_COPYAREA
1177        select FB_CFB_IMAGEBLIT
1178        help
1179          This driver supports the LE80578 (Vermilion Range) chipset
1180
1181config FB_CARILLO_RANCH
1182        tristate "Intel Carillo Ranch support"
1183        depends on FB_LE80578 && FB && PCI && X86
1184        help
1185          This driver supports the LE80578 (Carillo Ranch) board
1186
1187config FB_INTEL
1188        tristate "Intel 830M/845G/852GM/855GM/865G/915G/945G/945GM/965G/965GM support"
1189        depends on FB && PCI && X86 && AGP_INTEL && EXPERT
1190        select FB_MODE_HELPERS
1191        select FB_CFB_FILLRECT
1192        select FB_CFB_COPYAREA
1193        select FB_CFB_IMAGEBLIT
1194        select FB_BOOT_VESA_SUPPORT if FB_INTEL = y
1195        depends on !DRM_I915
1196        help
1197          This driver supports the on-board graphics built in to the Intel
1198          830M/845G/852GM/855GM/865G/915G/915GM/945G/945GM/965G/965GM chipsets.
1199          Say Y if you have and plan to use such a board.
1200
1201          To make FB_INTELFB=Y work you need to say AGP_INTEL=y too.
1202
1203          To compile this driver as a module, choose M here: the
1204          module will be called intelfb.
1205
1206          For more information, please read <file:Documentation/fb/intelfb.txt>
1207
1208config FB_INTEL_DEBUG
1209        bool "Intel driver Debug Messages"
1210        depends on FB_INTEL
1211        ---help---
1212          Say Y here if you want the Intel driver to output all sorts
1213          of debugging information to provide to the maintainer when
1214          something goes wrong.
1215
1216config FB_INTEL_I2C
1217        bool "DDC/I2C for Intel framebuffer support"
1218        depends on FB_INTEL
1219        select FB_DDC
1220        default y
1221        help
1222          Say Y here if you want DDC/I2C support for your on-board Intel graphics.
1223
1224config FB_MATROX
1225        tristate "Matrox acceleration"
1226        depends on FB && PCI
1227        select FB_CFB_FILLRECT
1228        select FB_CFB_COPYAREA
1229        select FB_CFB_IMAGEBLIT
1230        select FB_TILEBLITTING
1231        select FB_MACMODES if PPC_PMAC
1232        ---help---
1233          Say Y here if you have a Matrox Millennium, Matrox Millennium II,
1234          Matrox Mystique, Matrox Mystique 220, Matrox Productiva G100, Matrox
1235          Mystique G200, Matrox Millennium G200, Matrox Marvel G200 video,
1236          Matrox G400, G450 or G550 card in your box.
1237
1238          To compile this driver as a module, choose M here: the
1239          module will be called matroxfb.
1240
1241          You can pass several parameters to the driver at boot time or at
1242          module load time. The parameters look like "video=matroxfb:XXX", and
1243          are described in <file:Documentation/fb/matroxfb.txt>.
1244
1245config FB_MATROX_MILLENIUM
1246        bool "Millennium I/II support"
1247        depends on FB_MATROX
1248        help
1249          Say Y here if you have a Matrox Millennium or Matrox Millennium II
1250          video card. If you select "Advanced lowlevel driver options" below,
1251          you should check 4 bpp packed pixel, 8 bpp packed pixel, 16 bpp
1252          packed pixel, 24 bpp packed pixel and 32 bpp packed pixel. You can
1253          also use font widths different from 8.
1254
1255config FB_MATROX_MYSTIQUE
1256        bool "Mystique support"
1257        depends on FB_MATROX
1258        help
1259          Say Y here if you have a Matrox Mystique or Matrox Mystique 220
1260          video card. If you select "Advanced lowlevel driver options" below,
1261          you should check 8 bpp packed pixel, 16 bpp packed pixel, 24 bpp
1262          packed pixel and 32 bpp packed pixel. You can also use font widths
1263          different from 8.
1264
1265config FB_MATROX_G
1266        bool "G100/G200/G400/G450/G550 support"
1267        depends on FB_MATROX
1268        ---help---
1269          Say Y here if you have a Matrox G100, G200, G400, G450 or G550 based
1270          video card. If you select "Advanced lowlevel driver options", you
1271          should check 8 bpp packed pixel, 16 bpp packed pixel, 24 bpp packed
1272          pixel and 32 bpp packed pixel. You can also use font widths
1273          different from 8.
1274
1275          If you need support for G400 secondary head, you must say Y to
1276          "Matrox I2C support" and "G400 second head support" right below.
1277          G450/G550 secondary head and digital output are supported without
1278          additional modules.
1279
1280          The driver starts in monitor mode. You must use the matroxset tool 
1281          (available at <ftp://platan.vc.cvut.cz/pub/linux/matrox-latest/>) to 
1282          swap primary and secondary head outputs, or to change output mode.  
1283          Secondary head driver always start in 640x480 resolution and you 
1284          must use fbset to change it.
1285
1286          Do not forget that second head supports only 16 and 32 bpp
1287          packed pixels, so it is a good idea to compile them into the kernel
1288          too. You can use only some font widths, as the driver uses generic
1289          painting procedures (the secondary head does not use acceleration
1290          engine).
1291
1292          G450/G550 hardware can display TV picture only from secondary CRTC,
1293          and it performs no scaling, so picture must have 525 or 625 lines.
1294
1295config FB_MATROX_I2C
1296        tristate "Matrox I2C support"
1297        depends on FB_MATROX
1298        select FB_DDC
1299        ---help---
1300          This drivers creates I2C buses which are needed for accessing the
1301          DDC (I2C) bus present on all Matroxes, an I2C bus which
1302          interconnects Matrox optional devices, like MGA-TVO on G200 and
1303          G400, and the secondary head DDC bus, present on G400 only.
1304
1305          You can say Y or M here if you want to experiment with monitor
1306          detection code. You must say Y or M here if you want to use either
1307          second head of G400 or MGA-TVO on G200 or G400.
1308
1309          If you compile it as module, it will create a module named
1310          i2c-matroxfb.
1311
1312config FB_MATROX_MAVEN
1313        tristate "G400 second head support"
1314        depends on FB_MATROX_G && FB_MATROX_I2C
1315        ---help---
1316          WARNING !!! This support does not work with G450 !!!
1317
1318          Say Y or M here if you want to use a secondary head (meaning two
1319          monitors in parallel) on G400 or MGA-TVO add-on on G200. Secondary
1320          head is not compatible with accelerated XFree 3.3.x SVGA servers -
1321          secondary head output is blanked while you are in X. With XFree
1322          3.9.17 preview you can use both heads if you use SVGA over fbdev or
1323          the fbdev driver on first head and the fbdev driver on second head.
1324
1325          If you compile it as module, two modules are created,
1326          matroxfb_crtc2 and matroxfb_maven. Matroxfb_maven is needed for
1327          both G200 and G400, matroxfb_crtc2 is needed only by G400. You must
1328          also load i2c-matroxfb to get it to run.
1329
1330          The driver starts in monitor mode and you must use the matroxset
1331          tool (available at
1332          <ftp://platan.vc.cvut.cz/pub/linux/matrox-latest/>) to switch it to
1333          PAL or NTSC or to swap primary and secondary head outputs.
1334          Secondary head driver also always start in 640x480 resolution, you
1335          must use fbset to change it.
1336
1337          Also do not forget that second head supports only 16 and 32 bpp
1338          packed pixels, so it is a good idea to compile them into the kernel
1339          too.  You can use only some font widths, as the driver uses generic
1340          painting procedures (the secondary head does not use acceleration
1341          engine).
1342
1343config FB_RADEON
1344        tristate "ATI Radeon display support"
1345        depends on FB && PCI
1346        select FB_BACKLIGHT if FB_RADEON_BACKLIGHT
1347        select FB_MODE_HELPERS
1348        select FB_CFB_FILLRECT
1349        select FB_CFB_COPYAREA
1350        select FB_CFB_IMAGEBLIT
1351        select FB_MACMODES if PPC_OF
1352        help
1353          Choose this option if you want to use an ATI Radeon graphics card as
1354          a framebuffer device.  There are both PCI and AGP versions.  You
1355          don't need to choose this to run the Radeon in plain VGA mode.
1356
1357          There is a product page at
1358          http://products.amd.com/en-us/GraphicCardResult.aspx
1359
1360config FB_RADEON_I2C
1361        bool "DDC/I2C for ATI Radeon support"
1362        depends on FB_RADEON
1363        select FB_DDC
1364        default y
1365        help
1366          Say Y here if you want DDC/I2C support for your Radeon board. 
1367
1368config FB_RADEON_BACKLIGHT
1369        bool "Support for backlight control"
1370        depends on FB_RADEON
1371        default y
1372        help
1373          Say Y here if you want to control the backlight of your display.
1374
1375config FB_RADEON_DEBUG
1376        bool "Lots of debug output from Radeon driver"
1377        depends on FB_RADEON
1378        default n
1379        help
1380          Say Y here if you want the Radeon driver to output all sorts
1381          of debugging information to provide to the maintainer when
1382          something goes wrong.
1383
1384config FB_ATY128
1385        tristate "ATI Rage128 display support"
1386        depends on FB && PCI
1387        select FB_CFB_FILLRECT
1388        select FB_CFB_COPYAREA
1389        select FB_CFB_IMAGEBLIT
1390        select FB_BACKLIGHT if FB_ATY128_BACKLIGHT
1391        select FB_MACMODES if PPC_PMAC
1392        help
1393          This driver supports graphics boards with the ATI Rage128 chips.
1394          Say Y if you have such a graphics board and read
1395          <file:Documentation/fb/aty128fb.txt>.
1396
1397          To compile this driver as a module, choose M here: the
1398          module will be called aty128fb.
1399
1400config FB_ATY128_BACKLIGHT
1401        bool "Support for backlight control"
1402        depends on FB_ATY128
1403        default y
1404        help
1405          Say Y here if you want to control the backlight of your display.
1406
1407config FB_ATY
1408        tristate "ATI Mach64 display support" if PCI || ATARI
1409        depends on FB && !SPARC32
1410        select FB_CFB_FILLRECT
1411        select FB_CFB_COPYAREA
1412        select FB_CFB_IMAGEBLIT
1413        select FB_BACKLIGHT if FB_ATY_BACKLIGHT
1414        select FB_MACMODES if PPC
1415        help
1416          This driver supports graphics boards with the ATI Mach64 chips.
1417          Say Y if you have such a graphics board.
1418
1419          To compile this driver as a module, choose M here: the
1420          module will be called atyfb.
1421
1422config FB_ATY_CT
1423        bool "Mach64 CT/VT/GT/LT (incl. 3D RAGE) support"
1424        depends on PCI && FB_ATY
1425        default y if SPARC64 && PCI
1426        help
1427          Say Y here to support use of ATI's 64-bit Rage boards (or other
1428          boards based on the Mach64 CT, VT, GT, and LT chipsets) as a
1429          framebuffer device.  The ATI product support page for these boards
1430          is at <http://support.ati.com/products/pc/mach64/mach64.html>.
1431
1432config FB_ATY_GENERIC_LCD
1433        bool "Mach64 generic LCD support"
1434        depends on FB_ATY_CT
1435        help
1436          Say Y if you have a laptop with an ATI Rage LT PRO, Rage Mobility,
1437          Rage XC, or Rage XL chipset.
1438
1439config FB_ATY_GX
1440        bool "Mach64 GX support" if PCI
1441        depends on FB_ATY
1442        default y if ATARI
1443        help
1444          Say Y here to support use of the ATI Mach64 Graphics Expression
1445          board (or other boards based on the Mach64 GX chipset) as a
1446          framebuffer device.  The ATI product support page for these boards
1447          is at
1448          <http://support.ati.com/products/pc/mach64/graphics_xpression.html>.
1449
1450config FB_ATY_BACKLIGHT
1451        bool "Support for backlight control"
1452        depends on FB_ATY
1453        default y
1454        help
1455          Say Y here if you want to control the backlight of your display.
1456
1457config FB_S3
1458        tristate "S3 Trio/Virge support"
1459        depends on FB && PCI
1460        select FB_CFB_FILLRECT
1461        select FB_CFB_COPYAREA
1462        select FB_CFB_IMAGEBLIT
1463        select FB_TILEBLITTING
1464        select FB_SVGALIB
1465        select VGASTATE
1466        select FONT_8x16 if FRAMEBUFFER_CONSOLE
1467        ---help---
1468          Driver for graphics boards with S3 Trio / S3 Virge chip.
1469
1470config FB_S3_DDC
1471        bool "DDC for S3 support"
1472        depends on FB_S3
1473        select FB_DDC
1474        default y
1475        help
1476          Say Y here if you want DDC support for your S3 graphics card.
1477
1478config FB_SAVAGE
1479        tristate "S3 Savage support"
1480        depends on FB && PCI
1481        select FB_MODE_HELPERS
1482        select FB_CFB_FILLRECT
1483        select FB_CFB_COPYAREA
1484        select FB_CFB_IMAGEBLIT
1485        select VGASTATE
1486        help
1487          This driver supports notebooks and computers with S3 Savage PCI/AGP
1488          chips.
1489
1490          Say Y if you have such a graphics card.
1491
1492          To compile this driver as a module, choose M here; the module
1493          will be called savagefb.
1494
1495config FB_SAVAGE_I2C
1496       bool "Enable DDC2 Support"
1497       depends on FB_SAVAGE
1498       select FB_DDC
1499       help
1500          This enables I2C support for S3 Savage Chipsets.  This is used
1501          only for getting EDID information from the attached display
1502          allowing for robust video mode handling and switching.
1503
1504          Because fbdev-2.6 requires that drivers must be able to
1505          independently validate video mode parameters, you should say Y
1506          here.
1507
1508config FB_SAVAGE_ACCEL
1509       bool "Enable Console Acceleration"
1510       depends on FB_SAVAGE
1511       default n
1512       help
1513          This option will compile in console acceleration support. If
1514          the resulting framebuffer console has bothersome glitches, then
1515          choose N here.
1516
1517config FB_SIS
1518        tristate "SiS/XGI display support"
1519        depends on FB && PCI
1520        select FB_CFB_FILLRECT
1521        select FB_CFB_COPYAREA
1522        select FB_CFB_IMAGEBLIT
1523        select FB_BOOT_VESA_SUPPORT if FB_SIS = y
1524        help
1525          This is the frame buffer device driver for the SiS 300, 315, 330
1526          and 340 series as well as XGI V3XT, V5, V8, Z7 graphics chipsets.
1527          Specs available at <http://www.sis.com> and <http://www.xgitech.com>.
1528
1529          To compile this driver as a module, choose M here; the module
1530          will be called sisfb.
1531
1532config FB_SIS_300
1533        bool "SiS 300 series support"
1534        depends on FB_SIS
1535        help
1536          Say Y here to support use of the SiS 300/305, 540, 630 and 730.
1537
1538config FB_SIS_315
1539        bool "SiS 315/330/340 series and XGI support"
1540        depends on FB_SIS
1541        help
1542          Say Y here to support use of the SiS 315, 330 and 340 series
1543          (315/H/PRO, 55x, 650, 651, 740, 330, 661, 741, 760, 761) as well
1544          as XGI V3XT, V5, V8 and Z7.
1545
1546config FB_VIA
1547       tristate "VIA UniChrome (Pro) and Chrome9 display support"
1548       depends on FB && PCI && X86
1549       select FB_CFB_FILLRECT
1550       select FB_CFB_COPYAREA
1551       select FB_CFB_IMAGEBLIT
1552       select I2C_ALGOBIT
1553       select I2C
1554       select GPIOLIB
1555       help
1556          This is the frame buffer device driver for Graphics chips of VIA
1557          UniChrome (Pro) Family (CLE266,PM800/CN400,P4M800CE/P4M800Pro/
1558          CN700/VN800,CX700/VX700,P4M890) and Chrome9 Family (K8M890,CN896
1559          /P4M900,VX800)
1560          Say Y if you have a VIA UniChrome graphics board.
1561
1562          To compile this driver as a module, choose M here: the
1563          module will be called viafb.
1564
1565if FB_VIA
1566
1567config FB_VIA_DIRECT_PROCFS
1568        bool "direct hardware access via procfs (DEPRECATED)(DANGEROUS)"
1569        depends on FB_VIA
1570        default n
1571        help
1572          Allow direct hardware access to some output registers via procfs.
1573          This is dangerous but may provide the only chance to get the
1574          correct output device configuration.
1575          Its use is strongly discouraged.
1576
1577config FB_VIA_X_COMPATIBILITY
1578        bool "X server compatibility"
1579        depends on FB_VIA
1580        default n
1581        help
1582          This option reduces the functionality (power saving, ...) of the
1583          framebuffer to avoid negative impact on the OpenChrome X server.
1584          If you use any X server other than fbdev you should enable this
1585          otherwise it should be safe to disable it and allow using all
1586          features.
1587
1588endif
1589
1590config FB_NEOMAGIC
1591        tristate "NeoMagic display support"
1592        depends on FB && PCI
1593        select FB_MODE_HELPERS
1594        select FB_CFB_FILLRECT
1595        select FB_CFB_COPYAREA
1596        select FB_CFB_IMAGEBLIT
1597        select VGASTATE
1598        help
1599          This driver supports notebooks with NeoMagic PCI chips.
1600          Say Y if you have such a graphics card. 
1601
1602          To compile this driver as a module, choose M here: the
1603          module will be called neofb.
1604
1605config FB_KYRO
1606        tristate "IMG Kyro support"
1607        depends on FB && PCI
1608        select FB_CFB_FILLRECT
1609        select FB_CFB_COPYAREA
1610        select FB_CFB_IMAGEBLIT
1611        help
1612          Say Y here if you have a STG4000 / Kyro / PowerVR 3 based
1613          graphics board.
1614
1615          To compile this driver as a module, choose M here: the
1616          module will be called kyrofb.
1617
1618config FB_3DFX
1619        tristate "3Dfx Banshee/Voodoo3/Voodoo5 display support"
1620        depends on FB && PCI
1621        select FB_CFB_IMAGEBLIT
1622        select FB_CFB_FILLRECT
1623        select FB_CFB_COPYAREA
1624        select FB_MODE_HELPERS
1625        help
1626          This driver supports graphics boards with the 3Dfx Banshee,
1627          Voodoo3 or VSA-100 (aka Voodoo4/5) chips. Say Y if you have
1628          such a graphics board.
1629
1630          To compile this driver as a module, choose M here: the
1631          module will be called tdfxfb.
1632
1633config FB_3DFX_ACCEL
1634        bool "3Dfx Acceleration functions"
1635        depends on FB_3DFX
1636        ---help---
1637        This will compile the 3Dfx Banshee/Voodoo3/VSA-100 frame buffer
1638        device driver with acceleration functions.
1639
1640config FB_3DFX_I2C
1641        bool "Enable DDC/I2C support"
1642        depends on FB_3DFX
1643        select FB_DDC
1644        default y
1645        help
1646          Say Y here if you want DDC/I2C support for your 3dfx Voodoo3.
1647
1648config FB_VOODOO1
1649        tristate "3Dfx Voodoo Graphics (sst1) support"
1650        depends on FB && PCI
1651        select FB_CFB_FILLRECT
1652        select FB_CFB_COPYAREA
1653        select FB_CFB_IMAGEBLIT
1654        ---help---
1655          Say Y here if you have a 3Dfx Voodoo Graphics (Voodoo1/sst1) or 
1656          Voodoo2 (cvg) based graphics card.
1657
1658          To compile this driver as a module, choose M here: the
1659          module will be called sstfb.
1660
1661          WARNING: Do not use any application that uses the 3D engine
1662          (namely glide) while using this driver.
1663          Please read the <file:Documentation/fb/sstfb.txt> for supported
1664          options and other important info  support.
1665
1666config FB_VT8623
1667        tristate "VIA VT8623 support"
1668        depends on FB && PCI
1669        select FB_CFB_FILLRECT
1670        select FB_CFB_COPYAREA
1671        select FB_CFB_IMAGEBLIT
1672        select FB_TILEBLITTING
1673        select FB_SVGALIB
1674        select VGASTATE
1675        select FONT_8x16 if FRAMEBUFFER_CONSOLE
1676        ---help---
1677          Driver for CastleRock integrated graphics core in the
1678          VIA VT8623 [Apollo CLE266] chipset.
1679
1680config FB_TRIDENT
1681        tristate "Trident/CyberXXX/CyberBlade support"
1682        depends on FB && PCI
1683        select FB_CFB_FILLRECT
1684        select FB_CFB_COPYAREA
1685        select FB_CFB_IMAGEBLIT
1686        ---help---
1687          This is the frame buffer device driver for Trident PCI/AGP chipsets.
1688          Supported chipset families are TGUI 9440/96XX, 3DImage, Blade3D
1689          and Blade XP.
1690          There are also integrated versions of these chips called CyberXXXX,
1691          CyberImage or CyberBlade. These chips are mostly found in laptops
1692          but also on some motherboards including early VIA EPIA motherboards.
1693          For more information, read <file:Documentation/fb/tridentfb.txt>
1694
1695          Say Y if you have such a graphics board.
1696
1697          To compile this driver as a module, choose M here: the
1698          module will be called tridentfb.
1699
1700config FB_ARK
1701        tristate "ARK 2000PV support"
1702        depends on FB && PCI
1703        select FB_CFB_FILLRECT
1704        select FB_CFB_COPYAREA
1705        select FB_CFB_IMAGEBLIT
1706        select FB_TILEBLITTING
1707        select FB_SVGALIB
1708        select VGASTATE
1709        select FONT_8x16 if FRAMEBUFFER_CONSOLE
1710        ---help---
1711          Driver for PCI graphics boards with ARK 2000PV chip
1712          and ICS 5342 RAMDAC.
1713
1714config FB_PM3
1715        tristate "Permedia3 support"
1716        depends on FB && PCI
1717        select FB_CFB_FILLRECT
1718        select FB_CFB_COPYAREA
1719        select FB_CFB_IMAGEBLIT
1720        help
1721          This is the frame buffer device driver for the 3DLabs Permedia3
1722          chipset, used in Formac ProFormance III, 3DLabs Oxygen VX1 &
1723          similar boards, 3DLabs Permedia3 Create!, Appian Jeronimo 2000
1724          and maybe other boards.
1725
1726config FB_CARMINE
1727        tristate "Fujitsu carmine frame buffer support"
1728        depends on FB && PCI
1729        select FB_CFB_FILLRECT
1730        select FB_CFB_COPYAREA
1731        select FB_CFB_IMAGEBLIT
1732        help
1733          This is the frame buffer device driver for the Fujitsu Carmine chip.
1734          The driver provides two independent frame buffer devices.
1735
1736choice
1737        depends on FB_CARMINE
1738        prompt "DRAM timing"
1739        default FB_CARMINE_DRAM_EVAL
1740
1741config FB_CARMINE_DRAM_EVAL
1742        bool "Eval board timings"
1743        help
1744          Use timings which work on the eval card.
1745
1746config CARMINE_DRAM_CUSTOM
1747        bool "Custom board timings"
1748        help
1749          Use custom board timings.
1750endchoice
1751
1752config FB_AU1100
1753        bool "Au1100 LCD Driver"
1754        depends on (FB = y) && MIPS_ALCHEMY
1755        select FB_CFB_FILLRECT
1756        select FB_CFB_COPYAREA
1757        select FB_CFB_IMAGEBLIT
1758        help
1759          This is the framebuffer driver for the AMD Au1100 SOC.  It can drive
1760          various panels and CRTs by passing in kernel cmd line option
1761          au1100fb:panel=<name>.
1762
1763config FB_AU1200
1764        bool "Au1200/Au1300 LCD Driver"
1765        depends on (FB = y) && MIPS_ALCHEMY
1766        select FB_SYS_FILLRECT
1767        select FB_SYS_COPYAREA
1768        select FB_SYS_IMAGEBLIT
1769        select FB_SYS_FOPS
1770        help
1771          This is the framebuffer driver for the Au1200/Au1300 SOCs.
1772          It can drive various panels and CRTs by passing in kernel cmd line
1773          option au1200fb:panel=<name>.
1774
1775config FB_VT8500
1776        bool "VIA VT8500 framebuffer support"
1777        depends on (FB = y) && ARM && ARCH_VT8500
1778        select FB_SYS_FILLRECT if (!FB_WMT_GE_ROPS)
1779        select FB_SYS_COPYAREA if (!FB_WMT_GE_ROPS)
1780        select FB_SYS_IMAGEBLIT
1781        select FB_MODE_HELPERS
1782        select VIDEOMODE_HELPERS
1783        help
1784          This is the framebuffer driver for VIA VT8500 integrated LCD
1785          controller.
1786
1787config FB_WM8505
1788        bool "Wondermedia WM8xxx-series frame buffer support"
1789        depends on (FB = y) && ARM && ARCH_VT8500
1790        select FB_SYS_FILLRECT if (!FB_WMT_GE_ROPS)
1791        select FB_SYS_COPYAREA if (!FB_WMT_GE_ROPS)
1792        select FB_SYS_IMAGEBLIT
1793        select FB_MODE_HELPERS
1794        select VIDEOMODE_HELPERS
1795        help
1796          This is the framebuffer driver for WonderMedia WM8xxx-series
1797          integrated LCD controller. This driver covers the WM8505, WM8650
1798          and WM8850 SoCs.
1799
1800config FB_WMT_GE_ROPS
1801        bool "VT8500/WM8xxx accelerated raster ops support"
1802        depends on (FB = y) && (FB_VT8500 || FB_WM8505)
1803        default n
1804        help
1805          This adds support for accelerated raster operations on the
1806          VIA VT8500 and Wondermedia 85xx series SoCs.
1807
1808source "drivers/video/geode/Kconfig"
1809
1810config FB_HIT
1811        tristate "HD64461 Frame Buffer support"
1812        depends on FB && HD64461
1813        select FB_CFB_FILLRECT
1814        select FB_CFB_COPYAREA
1815        select FB_CFB_IMAGEBLIT
1816        help
1817          This is the frame buffer device driver for the Hitachi HD64461 LCD
1818          frame buffer card.
1819
1820config FB_PMAG_AA
1821        bool "PMAG-AA TURBOchannel framebuffer support"
1822        depends on (FB = y) && TC
1823        select FB_CFB_FILLRECT
1824        select FB_CFB_COPYAREA
1825        select FB_CFB_IMAGEBLIT
1826        help
1827          Support for the PMAG-AA TURBOchannel framebuffer card (1280x1024x1)
1828          used mainly in the MIPS-based DECstation series.
1829
1830config FB_PMAG_BA
1831        tristate "PMAG-BA TURBOchannel framebuffer support"
1832        depends on FB && TC
1833        select FB_CFB_FILLRECT
1834        select FB_CFB_COPYAREA
1835        select FB_CFB_IMAGEBLIT
1836        help
1837          Support for the PMAG-BA TURBOchannel framebuffer card (1024x864x8)
1838          used mainly in the MIPS-based DECstation series.
1839
1840config FB_PMAGB_B
1841        tristate "PMAGB-B TURBOchannel framebuffer support"
1842        depends on FB && TC
1843        select FB_CFB_FILLRECT
1844        select FB_CFB_COPYAREA
1845        select FB_CFB_IMAGEBLIT
1846        help
1847          Support for the PMAGB-B TURBOchannel framebuffer card used mainly
1848          in the MIPS-based DECstation series. The card is currently only
1849          supported in 1280x1024x8 mode.
1850
1851config FB_MAXINE
1852        bool "Maxine (Personal DECstation) onboard framebuffer support"
1853        depends on (FB = y) && MACH_DECSTATION
1854        select FB_CFB_FILLRECT
1855        select FB_CFB_COPYAREA
1856        select FB_CFB_IMAGEBLIT
1857        help
1858          Support for the onboard framebuffer (1024x768x8) in the Personal
1859          DECstation series (Personal DECstation 5000/20, /25, /33, /50,
1860          Codename "Maxine").
1861
1862config FB_G364
1863        bool "G364 frame buffer support"
1864        depends on (FB = y) && (MIPS_MAGNUM_4000 || OLIVETTI_M700)
1865        select FB_CFB_FILLRECT
1866        select FB_CFB_COPYAREA
1867        select FB_CFB_IMAGEBLIT
1868        help
1869          The G364 driver is the framebuffer used in MIPS Magnum 4000 and
1870          Olivetti M700-10 systems.
1871
1872config FB_68328
1873        bool "Motorola 68328 native frame buffer support"
1874        depends on (FB = y) && (M68328 || M68EZ328 || M68VZ328)
1875        select FB_CFB_FILLRECT
1876        select FB_CFB_COPYAREA
1877        select FB_CFB_IMAGEBLIT
1878        help
1879          Say Y here if you want to support the built-in frame buffer of
1880          the Motorola 68328 CPU family.
1881
1882config FB_PXA168
1883        tristate "PXA168/910 LCD framebuffer support"
1884        depends on FB && (CPU_PXA168 || CPU_PXA910)
1885        select FB_CFB_FILLRECT
1886        select FB_CFB_COPYAREA
1887        select FB_CFB_IMAGEBLIT
1888        ---help---
1889          Frame buffer driver for the built-in LCD controller in the Marvell
1890          MMP processor.
1891
1892config FB_PXA
1893        tristate "PXA LCD framebuffer support"
1894        depends on FB && ARCH_PXA
1895        select FB_CFB_FILLRECT
1896        select FB_CFB_COPYAREA
1897        select FB_CFB_IMAGEBLIT
1898        ---help---
1899          Frame buffer driver for the built-in LCD controller in the Intel
1900          PXA2x0 processor.
1901
1902          This driver is also available as a module ( = code which can be
1903          inserted and removed from the running kernel whenever you want). The
1904          module will be called pxafb. If you want to compile it as a module,
1905          say M here and read <file:Documentation/kbuild/modules.txt>.
1906
1907          If unsure, say N.
1908
1909config FB_PXA_OVERLAY
1910        bool "Support PXA27x/PXA3xx Overlay(s) as framebuffer"
1911        default n
1912        depends on FB_PXA && (PXA27x || PXA3xx)
1913
1914config FB_PXA_SMARTPANEL
1915        bool "PXA Smartpanel LCD support"
1916        default n
1917        depends on FB_PXA
1918
1919config FB_PXA_PARAMETERS
1920        bool "PXA LCD command line parameters"
1921        default n
1922        depends on FB_PXA
1923        ---help---
1924          Enable the use of kernel command line or module parameters
1925          to configure the physical properties of the LCD panel when
1926          using the PXA LCD driver.
1927
1928          This option allows you to override the panel parameters
1929          supplied by the platform in order to support multiple
1930          different models of flatpanel. If you will only be using a
1931          single model of flatpanel then you can safely leave this
1932          option disabled.
1933
1934          <file:Documentation/fb/pxafb.txt> describes the available parameters.
1935
1936config PXA3XX_GCU
1937        tristate "PXA3xx 2D graphics accelerator driver"
1938        depends on FB_PXA
1939        help
1940          Kernelspace driver for the 2D graphics controller unit (GCU)
1941          found on PXA3xx processors. There is a counterpart driver in the
1942          DirectFB suite, see http://www.directfb.org/
1943
1944          If you compile this as a module, it will be called pxa3xx_gcu.
1945
1946config FB_MBX
1947        tristate "2700G LCD framebuffer support"
1948        depends on FB && ARCH_PXA
1949        select FB_CFB_FILLRECT
1950        select FB_CFB_COPYAREA
1951        select FB_CFB_IMAGEBLIT
1952        ---help---
1953          Framebuffer driver for the Intel 2700G (Marathon) Graphics
1954          Accelerator
1955
1956config FB_MBX_DEBUG
1957       bool "Enable debugging info via debugfs"
1958       depends on FB_MBX && DEBUG_FS
1959       default n
1960       ---help---
1961         Enable this if you want debugging information using the debug
1962         filesystem (debugfs)
1963
1964         If unsure, say N.
1965
1966config FB_FSL_DIU
1967        tristate "Freescale DIU framebuffer support"
1968        depends on FB && FSL_SOC
1969        select FB_MODE_HELPERS
1970        select FB_CFB_FILLRECT
1971        select FB_CFB_COPYAREA
1972        select FB_CFB_IMAGEBLIT
1973        select PPC_LIB_RHEAP
1974        ---help---
1975          Framebuffer driver for the Freescale SoC DIU
1976
1977config FB_W100
1978        tristate "W100 frame buffer support"
1979        depends on FB && ARCH_PXA
1980        select FB_CFB_FILLRECT
1981        select FB_CFB_COPYAREA
1982        select FB_CFB_IMAGEBLIT
1983        ---help---
1984          Frame buffer driver for the w100 as found on the Sharp SL-Cxx series.
1985          It can also drive the w3220 chip found on iPAQ hx4700.
1986
1987          This driver is also available as a module ( = code which can be
1988          inserted and removed from the running kernel whenever you want). The
1989          module will be called w100fb. If you want to compile it as a module,
1990          say M here and read <file:Documentation/kbuild/modules.txt>.
1991
1992          If unsure, say N.
1993
1994config FB_SH_MOBILE_LCDC
1995        tristate "SuperH Mobile LCDC framebuffer support"
1996        depends on FB && (SUPERH || ARCH_SHMOBILE) && HAVE_CLK
1997        select FB_SYS_FILLRECT
1998        select FB_SYS_COPYAREA
1999        select FB_SYS_IMAGEBLIT
2000        select FB_SYS_FOPS
2001        select FB_DEFERRED_IO
2002        select FB_BACKLIGHT
2003        select SH_MIPI_DSI if SH_LCD_MIPI_DSI
2004        ---help---
2005          Frame buffer driver for the on-chip SH-Mobile LCD controller.
2006
2007config FB_SH_MOBILE_HDMI
2008        tristate "SuperH Mobile HDMI controller support"
2009        depends on FB_SH_MOBILE_LCDC
2010        select FB_MODE_HELPERS
2011        select SOUND
2012        select SND
2013        select SND_SOC
2014        ---help---
2015          Driver for the on-chip SH-Mobile HDMI controller.
2016
2017config FB_TMIO
2018        tristate "Toshiba Mobile IO FrameBuffer support"
2019        depends on FB && MFD_CORE
2020        select FB_CFB_FILLRECT
2021        select FB_CFB_COPYAREA
2022        select FB_CFB_IMAGEBLIT
2023        ---help---
2024          Frame buffer driver for the Toshiba Mobile IO integrated as found
2025          on the Sharp SL-6000 series
2026
2027          This driver is also available as a module ( = code which can be
2028          inserted and removed from the running kernel whenever you want). The
2029          module will be called tmiofb. If you want to compile it as a module,
2030          say M here and read <file:Documentation/kbuild/modules.txt>.
2031
2032          If unsure, say N.
2033
2034config FB_TMIO_ACCELL
2035        bool "tmiofb acceleration"
2036        depends on FB_TMIO
2037        default y
2038
2039config FB_S3C
2040        tristate "Samsung S3C framebuffer support"
2041        depends on FB && (CPU_S3C2416 || ARCH_S3C64XX || ARCH_S5P64X0 || \
2042                ARCH_S5PC100 || ARCH_S5PV210 || ARCH_EXYNOS)
2043        select FB_CFB_FILLRECT
2044        select FB_CFB_COPYAREA
2045        select FB_CFB_IMAGEBLIT
2046        ---help---
2047          Frame buffer driver for the built-in FB controller in the Samsung
2048          SoC line from the S3C2443 onwards, including the S3C2416, S3C2450,
2049          and the S3C64XX series such as the S3C6400 and S3C6410.
2050
2051          These chips all have the same basic framebuffer design with the
2052          actual capabilities depending on the chip. For instance the S3C6400
2053          and S3C6410 support 4 hardware windows whereas the S3C24XX series
2054          currently only have two.
2055
2056          Currently the support is only for the S3C6400 and S3C6410 SoCs.
2057
2058config FB_S3C_DEBUG_REGWRITE
2059       bool "Debug register writes"
2060       depends on FB_S3C
2061       ---help---
2062         Show all register writes via pr_debug()
2063
2064config FB_S3C2410
2065        tristate "S3C2410 LCD framebuffer support"
2066        depends on FB && ARCH_S3C24XX
2067        select FB_CFB_FILLRECT
2068        select FB_CFB_COPYAREA
2069        select FB_CFB_IMAGEBLIT
2070        ---help---
2071          Frame buffer driver for the built-in LCD controller in the Samsung
2072          S3C2410 processor.
2073
2074          This driver is also available as a module ( = code which can be
2075          inserted and removed from the running kernel whenever you want). The
2076          module will be called s3c2410fb. If you want to compile it as a module,
2077          say M here and read <file:Documentation/kbuild/modules.txt>.
2078
2079          If unsure, say N.
2080config FB_S3C2410_DEBUG
2081        bool "S3C2410 lcd debug messages"
2082        depends on FB_S3C2410
2083        help
2084          Turn on debugging messages. Note that you can set/unset at run time
2085          through sysfs
2086
2087config FB_NUC900
2088        bool "NUC900 LCD framebuffer support"
2089        depends on FB && ARCH_W90X900
2090        select FB_CFB_FILLRECT
2091        select FB_CFB_COPYAREA
2092        select FB_CFB_IMAGEBLIT
2093        ---help---
2094          Frame buffer driver for the built-in LCD controller in the Nuvoton
2095          NUC900 processor
2096
2097config GPM1040A0_320X240
2098        bool "Giantplus Technology GPM1040A0 320x240 Color TFT LCD"
2099        depends on FB_NUC900
2100
2101config FB_NUC900_DEBUG
2102        bool "NUC900 lcd debug messages"
2103        depends on FB_NUC900
2104        help
2105          Turn on debugging messages. Note that you can set/unset at run time
2106          through sysfs
2107
2108config FB_SM501
2109        tristate "Silicon Motion SM501 framebuffer support"
2110        depends on FB && MFD_SM501
2111        select FB_CFB_FILLRECT
2112        select FB_CFB_COPYAREA
2113        select FB_CFB_IMAGEBLIT
2114        ---help---
2115          Frame buffer driver for the CRT and LCD controllers in the Silicon
2116          Motion SM501.
2117
2118          This driver is also available as a module ( = code which can be
2119          inserted and removed from the running kernel whenever you want). The
2120          module will be called sm501fb. If you want to compile it as a module,
2121          say M here and read <file:Documentation/kbuild/modules.txt>.
2122
2123          If unsure, say N.
2124
2125config FB_SMSCUFX
2126        tristate "SMSC UFX6000/7000 USB Framebuffer support"
2127        depends on FB && USB
2128        select FB_MODE_HELPERS
2129        select FB_SYS_FILLRECT
2130        select FB_SYS_COPYAREA
2131        select FB_SYS_IMAGEBLIT
2132        select FB_SYS_FOPS
2133        select FB_DEFERRED_IO
2134        ---help---
2135          This is a kernel framebuffer driver for SMSC UFX USB devices.
2136          Supports fbdev clients like xf86-video-fbdev, kdrive, fbi, and
2137          mplayer -vo fbdev. Supports both UFX6000 (USB 2.0) and UFX7000
2138          (USB 3.0) devices.
2139          To compile as a module, choose M here: the module name is smscufx.
2140
2141config FB_UDL
2142        tristate "Displaylink USB Framebuffer support"
2143        depends on FB && USB
2144        select FB_MODE_HELPERS
2145        select FB_SYS_FILLRECT
2146        select FB_SYS_COPYAREA
2147        select FB_SYS_IMAGEBLIT
2148        select FB_SYS_FOPS
2149        select FB_DEFERRED_IO
2150        ---help---
2151          This is a kernel framebuffer driver for DisplayLink USB devices.
2152          Supports fbdev clients like xf86-video-fbdev, kdrive, fbi, and
2153          mplayer -vo fbdev. Supports all USB 2.0 era DisplayLink devices.
2154          To compile as a module, choose M here: the module name is udlfb.
2155
2156config FB_IBM_GXT4500
2157        tristate "Framebuffer support for IBM GXT4000P/4500P/6000P/6500P adaptors"
2158        depends on FB && PPC
2159        select FB_CFB_FILLRECT
2160        select FB_CFB_COPYAREA
2161        select FB_CFB_IMAGEBLIT
2162        ---help---
2163          Say Y here to enable support for the IBM GXT4000P/6000P and
2164          GXT4500P/6500P display adaptor based on Raster Engine RC1000,
2165          found on some IBM System P (pSeries) machines. This driver
2166          doesn't use Geometry Engine GT1000.
2167
2168config FB_PS3
2169        tristate "PS3 GPU framebuffer driver"
2170        depends on FB && PS3_PS3AV
2171        select FB_SYS_FILLRECT
2172        select FB_SYS_COPYAREA
2173        select FB_SYS_IMAGEBLIT
2174        select FB_SYS_FOPS
2175        select VT_HW_CONSOLE_BINDING if FRAMEBUFFER_CONSOLE
2176        ---help---
2177          Include support for the virtual frame buffer in the PS3 platform.
2178
2179config FB_PS3_DEFAULT_SIZE_M
2180        int "PS3 default frame buffer size (in MiB)"
2181        depends on FB_PS3
2182        default 9
2183        ---help---
2184          This is the default size (in MiB) of the virtual frame buffer in
2185          the PS3.
2186          The default value can be overridden on the kernel command line
2187          using the "ps3fb" option (e.g. "ps3fb=9M");
2188
2189config FB_XILINX
2190        tristate "Xilinx frame buffer support"
2191        depends on FB && (XILINX_VIRTEX || MICROBLAZE)
2192        select FB_CFB_FILLRECT
2193        select FB_CFB_COPYAREA
2194        select FB_CFB_IMAGEBLIT
2195        ---help---
2196          Include support for the Xilinx ML300/ML403 reference design
2197          framebuffer. ML300 carries a 640*480 LCD display on the board,
2198          ML403 uses a standard DB15 VGA connector.
2199
2200config FB_GOLDFISH
2201        tristate "Goldfish Framebuffer"
2202        depends on FB && HAS_DMA
2203        select FB_CFB_FILLRECT
2204        select FB_CFB_COPYAREA
2205        select FB_CFB_IMAGEBLIT
2206        ---help---
2207          Framebuffer driver for Goldfish Virtual Platform
2208
2209config FB_COBALT
2210        tristate "Cobalt server LCD frame buffer support"
2211        depends on FB && (MIPS_COBALT || MIPS_SEAD3)
2212
2213config FB_SH7760
2214        bool "SH7760/SH7763/SH7720/SH7721 LCDC support"
2215        depends on FB && (CPU_SUBTYPE_SH7760 || CPU_SUBTYPE_SH7763 \
2216                || CPU_SUBTYPE_SH7720 || CPU_SUBTYPE_SH7721)
2217        select FB_CFB_FILLRECT
2218        select FB_CFB_COPYAREA
2219        select FB_CFB_IMAGEBLIT
2220        ---help---
2221          Support for the SH7760/SH7763/SH7720/SH7721 integrated
2222          (D)STN/TFT LCD Controller.
2223          Supports display resolutions up to 1024x1024 pixel, grayscale and
2224          color operation, with depths ranging from 1 bpp to 8 bpp monochrome
2225          and 8, 15 or 16 bpp color; 90 degrees clockwise display rotation for
2226          panels <= 320 pixel horizontal resolution.
2227
2228config FB_DA8XX
2229        tristate "DA8xx/OMAP-L1xx Framebuffer support"
2230        depends on FB && ARCH_DAVINCI_DA8XX
2231        select FB_CFB_FILLRECT
2232        select FB_CFB_COPYAREA
2233        select FB_CFB_IMAGEBLIT
2234        select FB_CFB_REV_PIXELS_IN_BYTE
2235        ---help---
2236          This is the frame buffer device driver for the TI LCD controller
2237          found on DA8xx/OMAP-L1xx SoCs.
2238          If unsure, say N.
2239
2240config FB_VIRTUAL
2241        tristate "Virtual Frame Buffer support (ONLY FOR TESTING!)"
2242        depends on FB
2243        select FB_SYS_FILLRECT
2244        select FB_SYS_COPYAREA
2245        select FB_SYS_IMAGEBLIT
2246        select FB_SYS_FOPS
2247        ---help---
2248          This is a `virtual' frame buffer device. It operates on a chunk of
2249          unswappable kernel memory instead of on the memory of a graphics
2250          board. This means you cannot see any output sent to this frame
2251          buffer device, while it does consume precious memory. The main use
2252          of this frame buffer device is testing and debugging the frame
2253          buffer subsystem. Do NOT enable it for normal systems! To protect
2254          the innocent, it has to be enabled explicitly at boot time using the
2255          kernel option `video=vfb:'.
2256
2257          To compile this driver as a module, choose M here: the
2258          module will be called vfb. In order to load it, you must use
2259          the vfb_enable=1 option.
2260
2261          If unsure, say N.
2262
2263config XEN_FBDEV_FRONTEND
2264        tristate "Xen virtual frame buffer support"
2265        depends on FB && XEN
2266        select FB_SYS_FILLRECT
2267        select FB_SYS_COPYAREA
2268        select FB_SYS_IMAGEBLIT
2269        select FB_SYS_FOPS
2270        select FB_DEFERRED_IO
2271        select INPUT_XEN_KBDDEV_FRONTEND if INPUT_MISC
2272        select XEN_XENBUS_FRONTEND
2273        default y
2274        help
2275          This driver implements the front-end of the Xen virtual
2276          frame buffer driver.  It communicates with a back-end
2277          in another domain.
2278
2279config FB_METRONOME
2280        tristate "E-Ink Metronome/8track controller support"
2281        depends on FB
2282        select FB_SYS_FILLRECT
2283        select FB_SYS_COPYAREA
2284        select FB_SYS_IMAGEBLIT
2285        select FB_SYS_FOPS
2286        select FB_DEFERRED_IO
2287        help
2288          This driver implements support for the E-Ink Metronome
2289          controller. The pre-release name for this device was 8track
2290          and could also have been called by some vendors as PVI-nnnn.
2291
2292config FB_MB862XX
2293        tristate "Fujitsu MB862xx GDC support"
2294        depends on FB
2295        depends on PCI || (OF && PPC)
2296        select FB_CFB_FILLRECT
2297        select FB_CFB_COPYAREA
2298        select FB_CFB_IMAGEBLIT
2299        ---help---
2300          Frame buffer driver for Fujitsu Carmine/Coral-P(A)/Lime controllers.
2301
2302choice
2303        prompt "GDC variant"
2304        depends on FB_MB862XX
2305
2306config FB_MB862XX_PCI_GDC
2307        bool "Carmine/Coral-P(A) GDC"
2308        depends on PCI
2309        ---help---
2310          This enables framebuffer support for Fujitsu Carmine/Coral-P(A)
2311          PCI graphics controller devices.
2312
2313config FB_MB862XX_LIME
2314        bool "Lime GDC"
2315        depends on OF && PPC
2316        select FB_FOREIGN_ENDIAN
2317        select FB_LITTLE_ENDIAN
2318        ---help---
2319          Framebuffer support for Fujitsu Lime GDC on host CPU bus.
2320
2321endchoice
2322
2323config FB_MB862XX_I2C
2324        bool "Support I2C bus on MB862XX GDC"
2325        depends on FB_MB862XX && I2C
2326        default y
2327        help
2328          Selecting this option adds Coral-P(A)/Lime GDC I2C bus adapter
2329          driver to support accessing I2C devices on controller's I2C bus.
2330          These are usually some video decoder chips.
2331
2332config FB_EP93XX
2333        tristate "EP93XX frame buffer support"
2334        depends on FB && ARCH_EP93XX
2335        select FB_CFB_FILLRECT
2336        select FB_CFB_COPYAREA
2337        select FB_CFB_IMAGEBLIT
2338        ---help---
2339          Framebuffer driver for the Cirrus Logic EP93XX series of processors.
2340          This driver is also available as a module. The module will be called
2341          ep93xx-fb.
2342
2343config FB_PRE_INIT_FB
2344        bool "Don't reinitialize, use bootloader's GDC/Display configuration"
2345        depends on FB && FB_MB862XX_LIME
2346        ---help---
2347          Select this option if display contents should be inherited as set by
2348          the bootloader.
2349
2350config FB_MSM
2351        tristate "MSM Framebuffer support"
2352        depends on FB && ARCH_MSM
2353        select FB_CFB_FILLRECT
2354        select FB_CFB_COPYAREA
2355        select FB_CFB_IMAGEBLIT
2356
2357config FB_MX3
2358        tristate "MX3 Framebuffer support"
2359        depends on FB && MX3_IPU
2360        select FB_CFB_FILLRECT
2361        select FB_CFB_COPYAREA
2362        select FB_CFB_IMAGEBLIT
2363        default y
2364        help
2365          This is a framebuffer device for the i.MX31 LCD Controller. So
2366          far only synchronous displays are supported. If you plan to use
2367          an LCD display with your i.MX31 system, say Y here.
2368
2369config FB_BROADSHEET
2370        tristate "E-Ink Broadsheet/Epson S1D13521 controller support"
2371        depends on FB
2372        select FB_SYS_FILLRECT
2373        select FB_SYS_COPYAREA
2374        select FB_SYS_IMAGEBLIT
2375        select FB_SYS_FOPS
2376        select FB_DEFERRED_IO
2377        help
2378          This driver implements support for the E-Ink Broadsheet
2379          controller. The release name for this device was Epson S1D13521
2380          and could also have been called by other names when coupled with
2381          a bridge adapter.
2382
2383config FB_AUO_K190X
2384        tristate "AUO-K190X EPD controller support"
2385        depends on FB
2386        select FB_SYS_FILLRECT
2387        select FB_SYS_COPYAREA
2388        select FB_SYS_IMAGEBLIT
2389        select FB_SYS_FOPS
2390        select FB_DEFERRED_IO
2391        help
2392          Provides support for epaper controllers from the K190X series
2393          of AUO. These controllers can be used to drive epaper displays
2394          from Sipix.
2395
2396          This option enables the common support, shared by the individual
2397          controller drivers. You will also have to enable the driver
2398          for the controller type used in your device.
2399
2400config FB_AUO_K1900
2401        tristate "AUO-K1900 EPD controller support"
2402        depends on FB && FB_AUO_K190X
2403        help
2404          This driver implements support for the AUO K1900 epd-controller.
2405          This controller can drive Sipix epaper displays but can only do
2406          serial updates, reducing the number of possible frames per second.
2407
2408config FB_AUO_K1901
2409        tristate "AUO-K1901 EPD controller support"
2410        depends on FB && FB_AUO_K190X
2411        help
2412          This driver implements support for the AUO K1901 epd-controller.
2413          This controller can drive Sipix epaper displays and supports
2414          concurrent updates, making higher frames per second possible.
2415
2416config FB_JZ4740
2417        tristate "JZ4740 LCD framebuffer support"
2418        depends on FB && MACH_JZ4740
2419        select FB_SYS_FILLRECT
2420        select FB_SYS_COPYAREA
2421        select FB_SYS_IMAGEBLIT
2422        help
2423          Framebuffer support for the JZ4740 SoC.
2424
2425config FB_MXS
2426        tristate "MXS LCD framebuffer support"
2427        depends on FB && ARCH_MXS
2428        select FB_CFB_FILLRECT
2429        select FB_CFB_COPYAREA
2430        select FB_CFB_IMAGEBLIT
2431        select FB_MODE_HELPERS
2432        select VIDEOMODE_HELPERS
2433        help
2434          Framebuffer support for the MXS SoC.
2435
2436config FB_PUV3_UNIGFX
2437        tristate "PKUnity v3 Unigfx framebuffer support"
2438        depends on FB && UNICORE32 && ARCH_PUV3
2439        select FB_SYS_FILLRECT
2440        select FB_SYS_COPYAREA
2441        select FB_SYS_IMAGEBLIT
2442        select FB_SYS_FOPS
2443        help
2444          Choose this option if you want to use the Unigfx device as a
2445          framebuffer device. Without the support of PCI & AGP.
2446
2447config FB_HYPERV
2448        tristate "Microsoft Hyper-V Synthetic Video support"
2449        depends on FB && HYPERV
2450        select FB_CFB_FILLRECT
2451        select FB_CFB_COPYAREA
2452        select FB_CFB_IMAGEBLIT
2453        help
2454          This framebuffer driver supports Microsoft Hyper-V Synthetic Video.
2455
2456config FB_SIMPLE
2457        bool "Simple framebuffer support"
2458        depends on (FB = y) && OF
2459        select FB_CFB_FILLRECT
2460        select FB_CFB_COPYAREA
2461        select FB_CFB_IMAGEBLIT
2462        help
2463          Say Y if you want support for a simple frame-buffer.
2464
2465          This driver assumes that the display hardware has been initialized
2466          before the kernel boots, and the kernel will simply render to the
2467          pre-allocated frame buffer surface.
2468
2469          Configuration re: surface address, size, and format must be provided
2470          through device tree, or potentially plain old platform data in the
2471          future.
2472
2473source "drivers/video/omap/Kconfig"
2474source "drivers/video/omap2/Kconfig"
2475source "drivers/video/exynos/Kconfig"
2476source "drivers/video/mmp/Kconfig"
2477source "drivers/video/backlight/Kconfig"
2478
2479if VT
2480        source "drivers/video/console/Kconfig"
2481endif
2482
2483if FB || SGI_NEWPORT_CONSOLE
2484        source "drivers/video/logo/Kconfig"
2485endif
2486
2487config FB_SH_MOBILE_MERAM
2488        tristate "SuperH Mobile MERAM read ahead support"
2489        depends on (SUPERH || ARCH_SHMOBILE)
2490        select GENERIC_ALLOCATOR
2491        ---help---
2492          Enable MERAM support for the SuperH controller.
2493
2494          This will allow for caching of the framebuffer to provide more
2495          reliable access under heavy main memory bus traffic situations.
2496          Up to 4 memory channels can be configured, allowing 4 RGB or
2497          2 YCbCr framebuffers to be configured.
2498
2499config FB_SSD1307
2500        tristate "Solomon SSD1307 framebuffer support"
2501        depends on FB && I2C
2502        depends on OF
2503        depends on GPIOLIB
2504        select FB_SYS_FOPS
2505        select FB_SYS_FILLRECT
2506        select FB_SYS_COPYAREA
2507        select FB_SYS_IMAGEBLIT
2508        select FB_DEFERRED_IO
2509        select PWM
2510        help
2511          This driver implements support for the Solomon SSD1307
2512          OLED controller over I2C.
2513
2514endmenu
2515
lxr.linux.no kindly hosted by Redpill Linpro AS, provider of Linux consulting and operations services since 1995.