/*
 * Copyright (C) 2000                   Andre Hedrick <andre@linux-ide.org>
 * Copyright (C) 2000                   Mark Lord <mlord@pobox.com>
 * Copyright (C) 2007                   Bartlomiej Zolnierkiewicz
 *
 * May be copied or modified under the terms of the GNU General Public License
 *
 * Development of this chipset driver was funded
 * by the nice folks at National Semiconductor.
 *
 * Documentation:
 *      CS5530 documentation available from National Semiconductor.
 */

#include <linux/module.h>
#include <linux/types.h>
#include <linux/kernel.h>
#include <linux/pci.h>
#include <linux/init.h>
#include <linux/ide.h>

#include <asm/io.h>

#define DRV_NAME "cs5530"

/*
 * Here are the standard PIO mode 0-4 timings for each "format".
 * Format-0 uses fast data reg timings, with slower command reg timings.
 * Format-1 uses fast timings for all registers, but won't work with all drives.
 */
static unsigned int cs5530_pio_timings[2][5] = {
        {0x00009172, 0x00012171, 0x00020080, 0x00032010, 0x00040010},
        {0xd1329172, 0x71212171, 0x30200080, 0x20102010, 0x00100010}
};

/*
 * After chip reset, the PIO timings are set to 0x0000e132, which is not valid.
 */
#define CS5530_BAD_PIO(timings) (((timings)&~0x80000000)==0x0000e132)
#define CS5530_BASEREG(hwif)    (((hwif)->dma_base & ~0xf) + ((hwif)->channel ? 0x30 : 0x20))

/**
 *      cs5530_set_pio_mode     -       set host controller for PIO mode
 *      @drive: drive
 *      @pio: PIO mode number
 *
 *      Handles setting of PIO mode for the chipset.
 *
 *      The init_hwif_cs5530() routine guarantees that all drives
 *      will have valid default PIO timings set up before we get here.
 */

static void cs5530_set_pio_mode(ide_drive_t *drive, const u8 pio)
{
        unsigned long basereg = CS5530_BASEREG(drive->hwif);
        unsigned int format = (inl(basereg + 4) >> 31) & 1;

        outl(cs5530_pio_timings[format][pio], basereg + ((drive->dn & 1)<<3));
}

/**
 *      cs5530_udma_filter      -       UDMA filter
 *      @drive: drive
 *
 *      cs5530_udma_filter() does UDMA mask filtering for the given drive
 *      taking into the consideration capabilities of the mate device.
 *
 *      The CS5530 specifies that two drives sharing a cable cannot mix
 *      UDMA/MDMA.  It has to be one or the other, for the pair, though
 *      different timings can still be chosen for each drive.  We could
 *      set the appropriate timing bits on the fly, but that might be
 *      a bit confusing.  So, for now we statically handle this requirement
 *      by looking at our mate drive to see what it is capable of, before
 *      choosing a mode for our own drive.
 *
 *      Note: This relies on the fact we never fail from UDMA to MWDMA2
 *      but instead drop to PIO.
 */

static u8 cs5530_udma_filter(ide_drive_t *drive)
{
        ide_hwif_t *hwif = drive->hwif;
        ide_drive_t *mate = ide_get_pair_dev(drive);
        u16 *mateid;
        u8 mask = hwif->ultra_mask;

        if (mate == NULL)
                goto out;
        mateid = mate->id;

        if (ata_id_has_dma(mateid) && __ide_dma_bad_drive(mate) == 0) {
                if ((mateid[ATA_ID_FIELD_VALID] & 4) &&
                    (mateid[ATA_ID_UDMA_MODES] & 7))
                        goto out;
                if (mateid[ATA_ID_MWDMA_MODES] & 7)
                        mask = 0;
        }
out:
        return mask;
}

static void cs5530_set_dma_mode(ide_drive_t *drive, const u8 mode)
{
        unsigned long basereg;
        unsigned int reg, timings = 0;

        switch (mode) {
                case XFER_UDMA_0:       timings = 0x00921250; break;
                case XFER_UDMA_1:       timings = 0x00911140; break;
                case XFER_UDMA_2:       timings = 0x00911030; break;
                case XFER_MW_DMA_0:     timings = 0x00077771; break;
                case XFER_MW_DMA_1:     timings = 0x00012121; break;
                case XFER_MW_DMA_2:     timings = 0x00002020; break;
        }
        basereg = CS5530_BASEREG(drive->hwif);
        reg = inl(basereg + 4);                 /* get drive0 config register */
        timings |= reg & 0x80000000;            /* preserve PIO format bit */
        if ((drive-> dn & 1) == 0) {            /* are we configuring drive0? */
                outl(timings, basereg + 4);     /* write drive0 config register */
        } else {
                if (timings & 0x00100000)
                        reg |=  0x00100000;     /* enable UDMA timings for both drives */
                else
                        reg &= ~0x00100000;     /* disable UDMA timings for both drives */
                outl(reg, basereg + 4);         /* write drive0 config register */
                outl(timings, basereg + 12);    /* write drive1 config register */
        }
}

/**
 *      init_chipset_5530       -       set up 5530 bridge
 *      @dev: PCI device
 *
 *      Initialize the cs5530 bridge for reliable IDE DMA operation.
 */

static int init_chipset_cs5530(struct pci_dev *dev)
{
        struct pci_dev *master_0 = NULL, *cs5530_0 = NULL;

        if (pci_resource_start(dev, 4) == 0)
                return -EFAULT;

        dev = NULL;
        while ((dev = pci_get_device(PCI_VENDOR_ID_CYRIX, PCI_ANY_ID, dev)) != NULL) {
                switch (dev->device) {
                        case PCI_DEVICE_ID_CYRIX_PCI_MASTER:
                                master_0 = pci_dev_get(dev);
                                break;
                        case PCI_DEVICE_ID_CYRIX_5530_LEGACY:
                                cs5530_0 = pci_dev_get(dev);
                                break;
                }
        }
        if (!master_0) {
                printk(KERN_ERR DRV_NAME ": unable to locate PCI MASTER function\n");
                goto out;
        }
        if (!cs5530_0) {
                printk(KERN_ERR DRV_NAME ": unable to locate CS5530 LEGACY function\n");
                goto out;
        }

        /*
         * Enable BusMaster and MemoryWriteAndInvalidate for the cs5530:
         * -->  OR 0x14 into 16-bit PCI COMMAND reg of function 0 of the cs5530
         */

        pci_set_master(cs5530_0);
        pci_try_set_mwi(cs5530_0);

        /*
         * Set PCI CacheLineSize to 16-bytes:
         * --> Write 0x04 into 8-bit PCI CACHELINESIZE reg of function 0 of the cs5530
         */

        pci_write_config_byte(cs5530_0, PCI_CACHE_LINE_SIZE, 0x04);

        /*
         * Disable trapping of UDMA register accesses (Win98 hack):
         * --> Write 0x5006 into 16-bit reg at offset 0xd0 of function 0 of the cs5530
         */

        pci_write_config_word(cs5530_0, 0xd0, 0x5006);

        /*
         * Bit-1 at 0x40 enables MemoryWriteAndInvalidate on internal X-bus:
         * The other settings are what is necessary to get the register
         * into a sane state for IDE DMA operation.
         */

        pci_write_config_byte(master_0, 0x40, 0x1e);

        /* 
         * Set max PCI burst size (16-bytes seems to work best):
         *         16bytes: set bit-1 at 0x41 (reg value of 0x16)
         *      all others: clear bit-1 at 0x41, and do:
         *        128bytes: OR 0x00 at 0x41
         *        256bytes: OR 0x04 at 0x41
         *        512bytes: OR 0x08 at 0x41
         *       1024bytes: OR 0x0c at 0x41
         */

        pci_write_config_byte(master_0, 0x41, 0x14);

        /*
         * These settings are necessary to get the chip
         * into a sane state for IDE DMA operation.
         */

        pci_write_config_byte(master_0, 0x42, 0x00);
        pci_write_config_byte(master_0, 0x43, 0xc1);

out:
        pci_dev_put(master_0);
        pci_dev_put(cs5530_0);
        return 0;
}

/**
 *      init_hwif_cs5530        -       initialise an IDE channel
 *      @hwif: IDE to initialize
 *
 *      This gets invoked by the IDE driver once for each channel. It
 *      performs channel-specific pre-initialization before drive probing.
 */

static void __devinit init_hwif_cs5530 (ide_hwif_t *hwif)
{
        unsigned long basereg;
        u32 d0_timings;

        basereg = CS5530_BASEREG(hwif);
        d0_timings = inl(basereg + 0);
        if (CS5530_BAD_PIO(d0_timings))
                outl(cs5530_pio_timings[(d0_timings >> 31) & 1][0], basereg + 0);
        if (CS5530_BAD_PIO(inl(basereg + 8)))
                outl(cs5530_pio_timings[(d0_timings >> 31) & 1][0], basereg + 8);
}

static const struct ide_port_ops cs5530_port_ops = {
        .set_pio_mode           = cs5530_set_pio_mode,
        .set_dma_mode           = cs5530_set_dma_mode,
        .udma_filter            = cs5530_udma_filter,
};

static const struct ide_port_info cs5530_chipset __devinitdata = {
        .name           = DRV_NAME,
        .init_chipset   = init_chipset_cs5530,
        .init_hwif      = init_hwif_cs5530,
        .port_ops       = &cs5530_port_ops,
        .host_flags     = IDE_HFLAG_SERIALIZE |
                          IDE_HFLAG_POST_SET_MODE,
        .pio_mask       = ATA_PIO4,
        .mwdma_mask     = ATA_MWDMA2,
        .udma_mask      = ATA_UDMA2,
};

static int __devinit cs5530_init_one(struct pci_dev *dev, const struct pci_device_id *id)
{
        return ide_pci_init_one(dev, &cs5530_chipset, NULL);
}

static const struct pci_device_id cs5530_pci_tbl[] = {
        { PCI_VDEVICE(CYRIX, PCI_DEVICE_ID_CYRIX_5530_IDE), 0 },
        { 0, },
};
MODULE_DEVICE_TABLE(pci, cs5530_pci_tbl);

static struct pci_driver cs5530_pci_driver = {
        .name           = "CS5530 IDE",
        .id_table       = cs5530_pci_tbl,
        .probe          = cs5530_init_one,
        .remove         = ide_pci_remove,
        .suspend        = ide_pci_suspend,
        .resume         = ide_pci_resume,
};

static int __init cs5530_ide_init(void)
{
        return ide_pci_register_driver(&cs5530_pci_driver);
}

static void __exit cs5530_ide_exit(void)
{
        pci_unregister_driver(&cs5530_pci_driver);
}

module_init(cs5530_ide_init);
module_exit(cs5530_ide_exit);

MODULE_AUTHOR("Mark Lord");
MODULE_DESCRIPTION("PCI driver module for Cyrix/NS 5530 IDE");
MODULE_LICENSE("GPL");