/*
 * f_sourcesink.c - USB peripheral source/sink configuration driver
 *
 * Copyright (C) 2003-2008 David Brownell
 * Copyright (C) 2008 by Nokia Corporation
 *
 * This program is free software; you can redistribute it and/or modify
 * it under the terms of the GNU General Public License as published by
 * the Free Software Foundation; either version 2 of the License, or
 * (at your option) any later version.
 *
 * This program is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 * GNU General Public License for more details.
 *
 * You should have received a copy of the GNU General Public License
 * along with this program; if not, write to the Free Software
 * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
 */

/* #define VERBOSE_DEBUG */

#include <linux/kernel.h>
#include <linux/utsname.h>
#include <linux/device.h>

#include "g_zero.h"
#include "gadget_chips.h"


/*
 * SOURCE/SINK FUNCTION ... a primary testing vehicle for USB peripheral
 * controller drivers.
 *
 * This just sinks bulk packets OUT to the peripheral and sources them IN
 * to the host, optionally with specific data patterns for integrity tests.
 * As such it supports basic functionality and load tests.
 *
 * In terms of control messaging, this supports all the standard requests
 * plus two that support control-OUT tests.  If the optional "autoresume"
 * mode is enabled, it provides good functional coverage for the "USBCV"
 * test harness from USB-IF.
 *
 * Note that because this doesn't queue more than one request at a time,
 * some other function must be used to test queueing logic.  The network
 * link (g_ether) is the best overall option for that, since its TX and RX
 * queues are relatively independent, will receive a range of packet sizes,
 * and can often be made to run out completely.  Those issues are important
 * when stress testing peripheral controller drivers.
 *
 *
 * This is currently packaged as a configuration driver, which can't be
 * combined with other functions to make composite devices.  However, it
 * can be combined with other independent configurations.
 */
struct f_sourcesink {
        struct usb_function     function;

        struct usb_ep           *in_ep;
        struct usb_ep           *out_ep;
        struct timer_list       resume;
};

static inline struct f_sourcesink *func_to_ss(struct usb_function *f)
{
        return container_of(f, struct f_sourcesink, function);
}

static unsigned autoresume;
module_param(autoresume, uint, 0);
MODULE_PARM_DESC(autoresume, "zero, or seconds before remote wakeup");

static unsigned pattern;
module_param(pattern, uint, 0);
MODULE_PARM_DESC(pattern, "0 = all zeroes, 1 = mod63 ");

/*-------------------------------------------------------------------------*/

static struct usb_interface_descriptor source_sink_intf = {
        .bLength =              sizeof source_sink_intf,
        .bDescriptorType =      USB_DT_INTERFACE,

        .bNumEndpoints =        2,
        .bInterfaceClass =      USB_CLASS_VENDOR_SPEC,
        /* .iInterface = DYNAMIC */
};

/* full speed support: */

static struct usb_endpoint_descriptor fs_source_desc = {
        .bLength =              USB_DT_ENDPOINT_SIZE,
        .bDescriptorType =      USB_DT_ENDPOINT,

        .bEndpointAddress =     USB_DIR_IN,
        .bmAttributes =         USB_ENDPOINT_XFER_BULK,
};

static struct usb_endpoint_descriptor fs_sink_desc = {
        .bLength =              USB_DT_ENDPOINT_SIZE,
        .bDescriptorType =      USB_DT_ENDPOINT,

        .bEndpointAddress =     USB_DIR_OUT,
        .bmAttributes =         USB_ENDPOINT_XFER_BULK,
};

static struct usb_descriptor_header *fs_source_sink_descs[] = {
        (struct usb_descriptor_header *) &source_sink_intf,
        (struct usb_descriptor_header *) &fs_sink_desc,
        (struct usb_descriptor_header *) &fs_source_desc,
        NULL,
};

/* high speed support: */

static struct usb_endpoint_descriptor hs_source_desc = {
        .bLength =              USB_DT_ENDPOINT_SIZE,
        .bDescriptorType =      USB_DT_ENDPOINT,

        .bmAttributes =         USB_ENDPOINT_XFER_BULK,
        .wMaxPacketSize =       __constant_cpu_to_le16(512),
};

static struct usb_endpoint_descriptor hs_sink_desc = {
        .bLength =              USB_DT_ENDPOINT_SIZE,
        .bDescriptorType =      USB_DT_ENDPOINT,

        .bmAttributes =         USB_ENDPOINT_XFER_BULK,
        .wMaxPacketSize =       __constant_cpu_to_le16(512),
};

static struct usb_descriptor_header *hs_source_sink_descs[] = {
        (struct usb_descriptor_header *) &source_sink_intf,
        (struct usb_descriptor_header *) &hs_source_desc,
        (struct usb_descriptor_header *) &hs_sink_desc,
        NULL,
};

/* function-specific strings: */

static struct usb_string strings_sourcesink[] = {
        [0].s = "source and sink data",
        {  }                    /* end of list */
};

static struct usb_gadget_strings stringtab_sourcesink = {
        .language       = 0x0409,       /* en-us */
        .strings        = strings_sourcesink,
};

static struct usb_gadget_strings *sourcesink_strings[] = {
        &stringtab_sourcesink,
        NULL,
};

/*-------------------------------------------------------------------------*/

static void sourcesink_autoresume(unsigned long _c)
{
        struct usb_composite_dev *cdev = (void *)_c;
        struct usb_gadget       *g = cdev->gadget;

        /* Normally the host would be woken up for something
         * more significant than just a timer firing; likely
         * because of some direct user request.
         */
        if (g->speed != USB_SPEED_UNKNOWN) {
                int status = usb_gadget_wakeup(g);
                DBG(cdev, "%s --> %d\n", __func__, status);
        }
}

static int __init
sourcesink_bind(struct usb_configuration *c, struct usb_function *f)
{
        struct usb_composite_dev *cdev = c->cdev;
        struct f_sourcesink     *ss = func_to_ss(f);
        int     id;

        /* allocate interface ID(s) */
        id = usb_interface_id(c, f);
        if (id < 0)
                return id;
        source_sink_intf.bInterfaceNumber = id;

        /* allocate endpoints */
        ss->in_ep = usb_ep_autoconfig(cdev->gadget, &fs_source_desc);
        if (!ss->in_ep) {
autoconf_fail:
                ERROR(cdev, "%s: can't autoconfigure on %s\n",
                        f->name, cdev->gadget->name);
                return -ENODEV;
        }
        ss->in_ep->driver_data = cdev;  /* claim */

        ss->out_ep = usb_ep_autoconfig(cdev->gadget, &fs_sink_desc);
        if (!ss->out_ep)
                goto autoconf_fail;
        ss->out_ep->driver_data = cdev; /* claim */

        setup_timer(&ss->resume, sourcesink_autoresume,
                        (unsigned long) c->cdev);

        /* support high speed hardware */
        if (gadget_is_dualspeed(c->cdev->gadget)) {
                hs_source_desc.bEndpointAddress =
                                fs_source_desc.bEndpointAddress;
                hs_sink_desc.bEndpointAddress =
                                fs_sink_desc.bEndpointAddress;
                f->hs_descriptors = hs_source_sink_descs;
        }

        DBG(cdev, "%s speed %s: IN/%s, OUT/%s\n",
                        gadget_is_dualspeed(c->cdev->gadget) ? "dual" : "full",
                        f->name, ss->in_ep->name, ss->out_ep->name);
        return 0;
}

static void
sourcesink_unbind(struct usb_configuration *c, struct usb_function *f)
{
        kfree(func_to_ss(f));
}

/* optionally require specific source/sink data patterns  */
static int check_read_data(struct f_sourcesink *ss, struct usb_request *req)
{
        unsigned                i;
        u8                      *buf = req->buf;
        struct usb_composite_dev *cdev = ss->function.config->cdev;

        for (i = 0; i < req->actual; i++, buf++) {
                switch (pattern) {

                /* all-zeroes has no synchronization issues */
                case 0:
                        if (*buf == 0)
                                continue;
                        break;

                /* "mod63" stays in sync with short-terminated transfers,
                 * OR otherwise when host and gadget agree on how large
                 * each usb transfer request should be.  Resync is done
                 * with set_interface or set_config.  (We *WANT* it to
                 * get quickly out of sync if controllers or their drivers
                 * stutter for any reason, including buffer duplcation...)
                 */
                case 1:
                        if (*buf == (u8)(i % 63))
                                continue;
                        break;
                }
                ERROR(cdev, "bad OUT byte, buf[%d] = %d\n", i, *buf);
                usb_ep_set_halt(ss->out_ep);
                return -EINVAL;
        }
        return 0;
}

static void reinit_write_data(struct usb_ep *ep, struct usb_request *req)
{
        unsigned        i;
        u8              *buf = req->buf;

        switch (pattern) {
        case 0:
                memset(req->buf, 0, req->length);
                break;
        case 1:
                for  (i = 0; i < req->length; i++)
                        *buf++ = (u8) (i % 63);
                break;
        }
}

static void source_sink_complete(struct usb_ep *ep, struct usb_request *req)
{
        struct f_sourcesink     *ss = ep->driver_data;
        struct usb_composite_dev *cdev = ss->function.config->cdev;
        int                     status = req->status;

        switch (status) {

        case 0:                         /* normal completion? */
                if (ep == ss->out_ep) {
                        check_read_data(ss, req);
                        memset(req->buf, 0x55, req->length);
                } else
                        reinit_write_data(ep, req);
                break;

        /* this endpoint is normally active while we're configured */
        case -ECONNABORTED:             /* hardware forced ep reset */
        case -ECONNRESET:               /* request dequeued */
        case -ESHUTDOWN:                /* disconnect from host */
                VDBG(cdev, "%s gone (%d), %d/%d\n", ep->name, status,
                                req->actual, req->length);
                if (ep == ss->out_ep)
                        check_read_data(ss, req);
                free_ep_req(ep, req);
                return;

        case -EOVERFLOW:                /* buffer overrun on read means that
                                         * we didn't provide a big enough
                                         * buffer.
                                         */
        default:
#if 1
                DBG(cdev, "%s complete --> %d, %d/%d\n", ep->name,
                                status, req->actual, req->length);
#endif
        case -EREMOTEIO:                /* short read */
                break;
        }

        status = usb_ep_queue(ep, req, GFP_ATOMIC);
        if (status) {
                ERROR(cdev, "kill %s:  resubmit %d bytes --> %d\n",
                                ep->name, req->length, status);
                usb_ep_set_halt(ep);
                /* FIXME recover later ... somehow */
        }
}

static int source_sink_start_ep(struct f_sourcesink *ss, bool is_in)
{
        struct usb_ep           *ep;
        struct usb_request      *req;
        int                     status;

        ep = is_in ? ss->in_ep : ss->out_ep;
        req = alloc_ep_req(ep);
        if (!req)
                return -ENOMEM;

        req->complete = source_sink_complete;
        if (is_in)
                reinit_write_data(ep, req);
        else
                memset(req->buf, 0x55, req->length);

        status = usb_ep_queue(ep, req, GFP_ATOMIC);
        if (status) {
                struct usb_composite_dev        *cdev;

                cdev = ss->function.config->cdev;
                ERROR(cdev, "start %s %s --> %d\n",
                                is_in ? "IN" : "OUT",
                                ep->name, status);
                free_ep_req(ep, req);
        }

        return status;
}

static void disable_source_sink(struct f_sourcesink *ss)
{
        struct usb_composite_dev        *cdev;

        cdev = ss->function.config->cdev;
        disable_endpoints(cdev, ss->in_ep, ss->out_ep);
        del_timer(&ss->resume);
        VDBG(cdev, "%s disabled\n", ss->function.name);
}

static int
enable_source_sink(struct usb_composite_dev *cdev, struct f_sourcesink *ss)
{
        int                                     result = 0;
        const struct usb_endpoint_descriptor    *src, *sink;
        struct usb_ep                           *ep;

        src = ep_choose(cdev->gadget, &hs_source_desc, &fs_source_desc);
        sink = ep_choose(cdev->gadget, &hs_sink_desc, &fs_sink_desc);

        /* one endpoint writes (sources) zeroes IN (to the host) */
        ep = ss->in_ep;
        result = usb_ep_enable(ep, src);
        if (result < 0)
                return result;
        ep->driver_data = ss;

        result = source_sink_start_ep(ss, true);
        if (result < 0) {
fail:
                ep = ss->in_ep;
                usb_ep_disable(ep);
                ep->driver_data = NULL;
                return result;
        }

        /* one endpoint reads (sinks) anything OUT (from the host) */
        ep = ss->out_ep;
        result = usb_ep_enable(ep, sink);
        if (result < 0)
                goto fail;
        ep->driver_data = ss;

        result = source_sink_start_ep(ss, false);
        if (result < 0) {
                usb_ep_disable(ep);
                ep->driver_data = NULL;
                goto fail;
        }

        DBG(cdev, "%s enabled\n", ss->function.name);
        return result;
}

static int sourcesink_set_alt(struct usb_function *f,
                unsigned intf, unsigned alt)
{
        struct f_sourcesink     *ss = func_to_ss(f);
        struct usb_composite_dev *cdev = f->config->cdev;

        /* we know alt is zero */
        if (ss->in_ep->driver_data)
                disable_source_sink(ss);
        return enable_source_sink(cdev, ss);
}

static void sourcesink_disable(struct usb_function *f)
{
        struct f_sourcesink     *ss = func_to_ss(f);

        disable_source_sink(ss);
}

static void sourcesink_suspend(struct usb_function *f)
{
        struct f_sourcesink     *ss = func_to_ss(f);
        struct usb_composite_dev *cdev = f->config->cdev;

        if (cdev->gadget->speed == USB_SPEED_UNKNOWN)
                return;

        if (autoresume) {
                mod_timer(&ss->resume, jiffies + (HZ * autoresume));
                DBG(cdev, "suspend, wakeup in %d seconds\n", autoresume);
        } else
                DBG(cdev, "%s\n", __func__);
}

static void sourcesink_resume(struct usb_function *f)
{
        struct f_sourcesink     *ss = func_to_ss(f);
        struct usb_composite_dev *cdev = f->config->cdev;

        DBG(cdev, "%s\n", __func__);
        del_timer(&ss->resume);
}

/*-------------------------------------------------------------------------*/

static int __init sourcesink_bind_config(struct usb_configuration *c)
{
        struct f_sourcesink     *ss;
        int                     status;

        ss = kzalloc(sizeof *ss, GFP_KERNEL);
        if (!ss)
                return -ENOMEM;

        ss->function.name = "source/sink";
        ss->function.descriptors = fs_source_sink_descs;
        ss->function.bind = sourcesink_bind;
        ss->function.unbind = sourcesink_unbind;
        ss->function.set_alt = sourcesink_set_alt;
        ss->function.disable = sourcesink_disable;
        ss->function.suspend = sourcesink_suspend;
        ss->function.resume = sourcesink_resume;

        status = usb_add_function(c, &ss->function);
        if (status)
                kfree(ss);
        return status;
}

static int sourcesink_setup(struct usb_configuration *c,
                const struct usb_ctrlrequest *ctrl)
{
        struct usb_request      *req = c->cdev->req;
        int                     value = -EOPNOTSUPP;
        u16                     w_index = le16_to_cpu(ctrl->wIndex);
        u16                     w_value = le16_to_cpu(ctrl->wValue);
        u16                     w_length = le16_to_cpu(ctrl->wLength);

        /* composite driver infrastructure handles everything except
         * the two control test requests.
         */
        switch (ctrl->bRequest) {

        /*
         * These are the same vendor-specific requests supported by
         * Intel's USB 2.0 compliance test devices.  We exceed that
         * device spec by allowing multiple-packet requests.
         *
         * NOTE:  the Control-OUT data stays in req->buf ... better
         * would be copying it into a scratch buffer, so that other
         * requests may safely intervene.
         */
        case 0x5b:      /* control WRITE test -- fill the buffer */
                if (ctrl->bRequestType != (USB_DIR_OUT|USB_TYPE_VENDOR))
                        goto unknown;
                if (w_value || w_index)
                        break;
                /* just read that many bytes into the buffer */
                if (w_length > req->length)
                        break;
                value = w_length;
                break;
        case 0x5c:      /* control READ test -- return the buffer */
                if (ctrl->bRequestType != (USB_DIR_IN|USB_TYPE_VENDOR))
                        goto unknown;
                if (w_value || w_index)
                        break;
                /* expect those bytes are still in the buffer; send back */
                if (w_length > req->length)
                        break;
                value = w_length;
                break;

        default:
unknown:
                VDBG(c->cdev,
                        "unknown control req%02x.%02x v%04x i%04x l%d\n",
                        ctrl->bRequestType, ctrl->bRequest,
                        w_value, w_index, w_length);
        }

        /* respond with data transfer or status phase? */
        if (value >= 0) {
                VDBG(c->cdev, "source/sink req%02x.%02x v%04x i%04x l%d\n",
                        ctrl->bRequestType, ctrl->bRequest,
                        w_value, w_index, w_length);
                req->zero = 0;
                req->length = value;
                value = usb_ep_queue(c->cdev->gadget->ep0, req, GFP_ATOMIC);
                if (value < 0)
                        ERROR(c->cdev, "source/sinkc response, err %d\n",
                                        value);
        }

        /* device either stalls (value < 0) or reports success */
        return value;
}

static struct usb_configuration sourcesink_driver = {
        .label          = "source/sink",
        .strings        = sourcesink_strings,
        .bind           = sourcesink_bind_config,
        .setup          = sourcesink_setup,
        .bConfigurationValue = 3,
        .bmAttributes   = USB_CONFIG_ATT_SELFPOWER,
        /* .iConfiguration = DYNAMIC */
};

/**
 * sourcesink_add - add a source/sink testing configuration to a device
 * @cdev: the device to support the configuration
 */
int __init sourcesink_add(struct usb_composite_dev *cdev)
{
        int id;

        /* allocate string ID(s) */
        id = usb_string_id(cdev);
        if (id < 0)
                return id;
        strings_sourcesink[0].id = id;

        source_sink_intf.iInterface = id;
        sourcesink_driver.iConfiguration = id;

        /* support autoresume for remote wakeup testing */
        if (autoresume)
                sourcesink_driver.bmAttributes |= USB_CONFIG_ATT_WAKEUP;

        /* support OTG systems */
        if (gadget_is_otg(cdev->gadget)) {
                sourcesink_driver.descriptors = otg_desc;
                sourcesink_driver.bmAttributes |= USB_CONFIG_ATT_WAKEUP;
        }

        return usb_add_config(cdev, &sourcesink_driver);
}