1# 2# For a description of the syntax of this configuration file, 3# see Documentation/kbuild/kconfig-language.txt. 4# 5config M68K 6 bool 7 default y 8 9config MMU 10 bool 11 default y 12 13config RWSEM_GENERIC_SPINLOCK 14 bool 15 default y 16 17config RWSEM_XCHGADD_ALGORITHM 18 bool 19 20config ARCH_HAS_ILOG2_U32 21 bool 22 default n 23 24config ARCH_HAS_ILOG2_U64 25 bool 26 default n 27 28config GENERIC_HWEIGHT 29 bool 30 default y 31 32config GENERIC_CALIBRATE_DELAY 33 bool 34 default y 35 36config TIME_LOW_RES 37 bool 38 default y 39 40config ARCH_MAY_HAVE_PC_FDC 41 bool 42 depends on Q40 || (BROKEN && SUN3X) 43 default y 44 45config NO_IOPORT 46 def_bool y 47 48mainmenu "Linux/68k Kernel Configuration" 49 50source "init/Kconfig" 51 52menu "Platform dependent setup" 53 54config EISA 55 bool 56 ---help--- 57 The Extended Industry Standard Architecture (EISA) bus was 58 developed as an open alternative to the IBM MicroChannel bus. 59 60 The EISA bus provided some of the features of the IBM MicroChannel 61 bus while maintaining backward compatibility with cards made for 62 the older ISA bus. The EISA bus saw limited use between 1988 and 63 1995 when it was made obsolete by the PCI bus. 64 65 Say Y here if you are building a kernel for an EISA-based machine. 66 67 Otherwise, say N. 68 69config MCA 70 bool 71 help 72 MicroChannel Architecture is found in some IBM PS/2 machines and 73 laptops. It is a bus system similar to PCI or ISA. See 74 <file:Documentation/mca.txt> (and especially the web page given 75 there) before attempting to build an MCA bus kernel. 76 77config PCMCIA 78 tristate 79 ---help--- 80 Say Y here if you want to attach PCMCIA- or PC-cards to your Linux 81 computer. These are credit-card size devices such as network cards, 82 modems or hard drives often used with laptops computers. There are 83 actually two varieties of these cards: the older 16 bit PCMCIA cards 84 and the newer 32 bit CardBus cards. If you want to use CardBus 85 cards, you need to say Y here and also to "CardBus support" below. 86 87 To use your PC-cards, you will need supporting software from David 88 Hinds' pcmcia-cs package (see the file <file:Documentation/Changes> 89 for location). Please also read the PCMCIA-HOWTO, available from 90 <http://www.tldp.org/docs.html#howto>. 91 92 To compile this driver as modules, choose M here: the 93 modules will be called pcmcia_core and ds. 94 95config SUN3 96 bool "Sun3 support" 97 select M68020 98 select MMU_SUN3 if MMU 99 help 100 This option enables support for the Sun 3 series of workstations 101 (3/50, 3/60, 3/1xx, 3/2xx systems). Enabling this option requires 102 that all other hardware types must be disabled, as Sun 3 kernels 103 are incompatible with all other m68k targets (including Sun 3x!). 104 105 If you don't want to compile a kernel exclusively for a Sun 3, say N. 106 107config AMIGA 108 bool "Amiga support" 109 depends on !MMU_SUN3 110 help 111 This option enables support for the Amiga series of computers. If 112 you plan to use this kernel on an Amiga, say Y here and browse the 113 material available in <file:Documentation/m68k>; otherwise say N. 114 115config ATARI 116 bool "Atari support" 117 depends on !MMU_SUN3 118 help 119 This option enables support for the 68000-based Atari series of 120 computers (including the TT, Falcon and Medusa). If you plan to use 121 this kernel on an Atari, say Y here and browse the material 122 available in <file:Documentation/m68k>; otherwise say N. 123 124config HADES 125 bool "Hades support" 126 depends on ATARI && BROKEN 127 help 128 This option enables support for the Hades Atari clone. If you plan 129 to use this kernel on a Hades, say Y here; otherwise say N. 130 131config PCI 132 bool 133 depends on HADES 134 default y 135 help 136 Find out whether you have a PCI motherboard. PCI is the name of a 137 bus system, i.e. the way the CPU talks to the other stuff inside 138 your box. Other bus systems are ISA, EISA, MicroChannel (MCA) or 139 VESA. If you have PCI, say Y, otherwise N. 140 141 The PCI-HOWTO, available from 142 <http://www.tldp.org/docs.html#howto>, contains valuable 143 information about which PCI hardware does work under Linux and which 144 doesn't. 145 146config MAC 147 bool "Macintosh support" 148 depends on !MMU_SUN3 149 help 150 This option enables support for the Apple Macintosh series of 151 computers (yes, there is experimental support now, at least for part 152 of the series). 153 154 Say N unless you're willing to code the remaining necessary support. 155 ;) 156 157config NUBUS 158 bool 159 depends on MAC 160 default y 161 162config M68K_L2_CACHE 163 bool 164 depends on MAC 165 default y 166 167config APOLLO 168 bool "Apollo support" 169 depends on !MMU_SUN3 170 help 171 Say Y here if you want to run Linux on an MC680x0-based Apollo 172 Domain workstation such as the DN3500. 173 174config VME 175 bool "VME (Motorola and BVM) support" 176 depends on !MMU_SUN3 177 help 178 Say Y here if you want to build a kernel for a 680x0 based VME 179 board. Boards currently supported include Motorola boards MVME147, 180 MVME162, MVME166, MVME167, MVME172, and MVME177. BVME4000 and 181 BVME6000 boards from BVM Ltd are also supported. 182 183config MVME147 184 bool "MVME147 support" 185 depends on VME 186 help 187 Say Y to include support for early Motorola VME boards. This will 188 build a kernel which can run on MVME147 single-board computers. If 189 you select this option you will have to select the appropriate 190 drivers for SCSI, Ethernet and serial ports later on. 191 192config MVME16x 193 bool "MVME162, 166 and 167 support" 194 depends on VME 195 help 196 Say Y to include support for Motorola VME boards. This will build a 197 kernel which can run on MVME162, MVME166, MVME167, MVME172, and 198 MVME177 boards. If you select this option you will have to select 199 the appropriate drivers for SCSI, Ethernet and serial ports later 200 on. 201 202config BVME6000 203 bool "BVME4000 and BVME6000 support" 204 depends on VME 205 help 206 Say Y to include support for VME boards from BVM Ltd. This will 207 build a kernel which can run on BVME4000 and BVME6000 boards. If 208 you select this option you will have to select the appropriate 209 drivers for SCSI, Ethernet and serial ports later on. 210 211config HP300 212 bool "HP9000/300 and HP9000/400 support" 213 depends on !MMU_SUN3 214 help 215 This option enables support for the HP9000/300 and HP9000/400 series 216 of workstations. Support for these machines is still somewhat 217 experimental. If you plan to try to use the kernel on such a machine 218 say Y here. 219 Everybody else says N. 220 221config DIO 222 bool "DIO bus support" 223 depends on HP300 224 default y 225 help 226 Say Y here to enable support for the "DIO" expansion bus used in 227 HP300 machines. If you are using such a system you almost certainly 228 want this. 229 230config SUN3X 231 bool "Sun3x support" 232 depends on !MMU_SUN3 233 select M68030 234 help 235 This option enables support for the Sun 3x series of workstations. 236 Be warned that this support is very experimental. 237 Note that Sun 3x kernels are not compatible with Sun 3 hardware. 238 General Linux information on the Sun 3x series (now discontinued) 239 is at <http://www.angelfire.com/ca2/tech68k/sun3.html>. 240 241 If you don't want to compile a kernel for a Sun 3x, say N. 242 243config Q40 244 bool "Q40/Q60 support" 245 depends on !MMU_SUN3 246 help 247 The Q40 is a Motorola 68040-based successor to the Sinclair QL 248 manufactured in Germany. There is an official Q40 home page at 249 <http://www.q40.de/>. This option enables support for the Q40 and 250 Q60. Select your CPU below. For 68LC060 don't forget to enable FPU 251 emulation. 252 253comment "Processor type" 254 255config M68020 256 bool "68020 support" 257 help 258 If you anticipate running this kernel on a computer with a MC68020 259 processor, say Y. Otherwise, say N. Note that the 68020 requires a 260 68851 MMU (Memory Management Unit) to run Linux/m68k, except on the 261 Sun 3, which provides its own version. 262 263config M68030 264 bool "68030 support" 265 depends on !MMU_SUN3 266 help 267 If you anticipate running this kernel on a computer with a MC68030 268 processor, say Y. Otherwise, say N. Note that a MC68EC030 will not 269 work, as it does not include an MMU (Memory Management Unit). 270 271config M68040 272 bool "68040 support" 273 depends on !MMU_SUN3 274 help 275 If you anticipate running this kernel on a computer with a MC68LC040 276 or MC68040 processor, say Y. Otherwise, say N. Note that an 277 MC68EC040 will not work, as it does not include an MMU (Memory 278 Management Unit). 279 280config M68060 281 bool "68060 support" 282 depends on !MMU_SUN3 283 help 284 If you anticipate running this kernel on a computer with a MC68060 285 processor, say Y. Otherwise, say N. 286 287config MMU_MOTOROLA 288 bool 289 depends on MMU && !MMU_SUN3 290 default y 291 292config MMU_SUN3 293 bool 294 295config M68KFPU_EMU 296 bool "Math emulation support (EXPERIMENTAL)" 297 depends on EXPERIMENTAL 298 help 299 At some point in the future, this will cause floating-point math 300 instructions to be emulated by the kernel on machines that lack a 301 floating-point math coprocessor. Thrill-seekers and chronically 302 sleep-deprived psychotic hacker types can say Y now, everyone else 303 should probably wait a while. 304 305config M68KFPU_EMU_EXTRAPREC 306 bool "Math emulation extra precision" 307 depends on M68KFPU_EMU 308 help 309 The fpu uses normally a few bit more during calculations for 310 correct rounding, the emulator can (often) do the same but this 311 extra calculation can cost quite some time, so you can disable 312 it here. The emulator will then "only" calculate with a 64 bit 313 mantissa and round slightly incorrect, what is more then enough 314 for normal usage. 315 316config M68KFPU_EMU_ONLY 317 bool "Math emulation only kernel" 318 depends on M68KFPU_EMU 319 help 320 This option prevents any floating-point instructions from being 321 compiled into the kernel, thereby the kernel doesn't save any 322 floating point context anymore during task switches, so this 323 kernel will only be usable on machines without a floating-point 324 math coprocessor. This makes the kernel a bit faster as no tests 325 needs to be executed whether a floating-point instruction in the 326 kernel should be executed or not. 327 328config ADVANCED 329 bool "Advanced configuration options" 330 ---help--- 331 This gives you access to some advanced options for the CPU. The 332 defaults should be fine for most users, but these options may make 333 it possible for you to improve performance somewhat if you know what 334 you are doing. 335 336 Note that the answer to this question won't directly affect the 337 kernel: saying N will just cause the configurator to skip all 338 the questions about these options. 339 340 Most users should say N to this question. 341 342config RMW_INSNS 343 bool "Use read-modify-write instructions" 344 depends on ADVANCED 345 ---help--- 346 This allows to use certain instructions that work with indivisible 347 read-modify-write bus cycles. While this is faster than the 348 workaround of disabling interrupts, it can conflict with DMA 349 ( = direct memory access) on many Amiga systems, and it is also said 350 to destabilize other machines. It is very likely that this will 351 cause serious problems on any Amiga or Atari Medusa if set. The only 352 configuration where it should work are 68030-based Ataris, where it 353 apparently improves performance. But you've been warned! Unless you 354 really know what you are doing, say N. Try Y only if you're quite 355 adventurous. 356 357config SINGLE_MEMORY_CHUNK 358 bool "Use one physical chunk of memory only" if ADVANCED && !SUN3 359 default y if SUN3 360 select NEED_MULTIPLE_NODES 361 help 362 Ignore all but the first contiguous chunk of physical memory for VM 363 purposes. This will save a few bytes kernel size and may speed up 364 some operations. Say N if not sure. 365 366config 060_WRITETHROUGH 367 bool "Use write-through caching for 68060 supervisor accesses" 368 depends on ADVANCED && M68060 369 ---help--- 370 The 68060 generally uses copyback caching of recently accessed data. 371 Copyback caching means that memory writes will be held in an on-chip 372 cache and only written back to memory some time later. Saying Y 373 here will force supervisor (kernel) accesses to use writethrough 374 caching. Writethrough caching means that data is written to memory 375 straight away, so that cache and memory data always agree. 376 Writethrough caching is less efficient, but is needed for some 377 drivers on 68060 based systems where the 68060 bus snooping signal 378 is hardwired on. The 53c710 SCSI driver is known to suffer from 379 this problem. 380 381config ARCH_DISCONTIGMEM_ENABLE 382 def_bool !SINGLE_MEMORY_CHUNK 383 384config NODES_SHIFT 385 int 386 default "3" 387 depends on !SINGLE_MEMORY_CHUNK 388 389source "mm/Kconfig" 390 391endmenu 392 393menu "General setup" 394 395source "fs/Kconfig.binfmt" 396 397config ZORRO 398 bool "Amiga Zorro (AutoConfig) bus support" 399 depends on AMIGA 400 help 401 This enables support for the Zorro bus in the Amiga. If you have 402 expansion cards in your Amiga that conform to the Amiga 403 AutoConfig(tm) specification, say Y, otherwise N. Note that even 404 expansion cards that do not fit in the Zorro slots but fit in e.g. 405 the CPU slot may fall in this category, so you have to say Y to let 406 Linux use these. 407 408config AMIGA_PCMCIA 409 bool "Amiga 1200/600 PCMCIA support (EXPERIMENTAL)" 410 depends on AMIGA && EXPERIMENTAL 411 help 412 Include support in the kernel for pcmcia on Amiga 1200 and Amiga 413 600. If you intend to use pcmcia cards say Y; otherwise say N. 414 415config STRAM_PROC 416 bool "ST-RAM statistics in /proc" 417 depends on ATARI 418 help 419 Say Y here to report ST-RAM usage statistics in /proc/stram. 420 421config HEARTBEAT 422 bool "Use power LED as a heartbeat" if AMIGA || APOLLO || ATARI || MAC ||Q40 423 default y if !AMIGA && !APOLLO && !ATARI && !MAC && !Q40 && HP300 424 help 425 Use the power-on LED on your machine as a load meter. The exact 426 behavior is platform-dependent, but normally the flash frequency is 427 a hyperbolic function of the 5-minute load average. 428 429# We have a dedicated heartbeat LED. :-) 430config PROC_HARDWARE 431 bool "/proc/hardware support" 432 help 433 Say Y here to support the /proc/hardware file, which gives you 434 access to information about the machine you're running on, 435 including the model, CPU, MMU, clock speed, BogoMIPS rating, 436 and memory size. 437 438config ISA 439 bool 440 depends on Q40 || AMIGA_PCMCIA || GG2 441 default y 442 help 443 Find out whether you have ISA slots on your motherboard. ISA is the 444 name of a bus system, i.e. the way the CPU talks to the other stuff 445 inside your box. Other bus systems are PCI, EISA, MicroChannel 446 (MCA) or VESA. ISA is an older system, now being displaced by PCI; 447 newer boards don't support it. If you have ISA, say Y, otherwise N. 448 449config GENERIC_ISA_DMA 450 bool 451 depends on Q40 || AMIGA_PCMCIA || GG2 452 default y 453 454config ZONE_DMA 455 bool 456 default y 457 458source "drivers/pci/Kconfig" 459 460source "drivers/zorro/Kconfig" 461 462endmenu 463 464source "net/Kconfig" 465 466source "drivers/Kconfig" 467 468menu "Character devices" 469 470config ATARI_MFPSER 471 tristate "Atari MFP serial support" 472 depends on ATARI 473 ---help--- 474 If you like to use the MFP serial ports ("Modem1", "Serial1") under 475 Linux, say Y. The driver equally supports all kinds of MFP serial 476 ports and automatically detects whether Serial1 is available. 477 478 To compile this driver as a module, choose M here. 479 480 Note for Falcon users: You also have an MFP port, it's just not 481 wired to the outside... But you could use the port under Linux. 482 483config ATARI_SCC 484 tristate "Atari SCC serial support" 485 depends on ATARI 486 ---help--- 487 If you have serial ports based on a Zilog SCC chip (Modem2, Serial2, 488 LAN) and like to use them under Linux, say Y. All built-in SCC's are 489 supported (TT, MegaSTE, Falcon), and also the ST-ESCC. If you have 490 two connectors for channel A (Serial2 and LAN), they are visible as 491 two separate devices. 492 493 To compile this driver as a module, choose M here. 494 495config ATARI_SCC_DMA 496 bool "Atari SCC serial DMA support" 497 depends on ATARI_SCC 498 help 499 This enables DMA support for receiving data on channel A of the SCC. 500 If you have a TT you may say Y here and read 501 drivers/char/atari_SCC.README. All other users should say N here, 502 because only the TT has SCC-DMA, even if your machine keeps claiming 503 so at boot time. 504 505config ATARI_MIDI 506 tristate "Atari MIDI serial support" 507 depends on ATARI 508 help 509 If you want to use your Atari's MIDI port in Linux, say Y. 510 511 To compile this driver as a module, choose M here. 512 513config ATARI_DSP56K 514 tristate "Atari DSP56k support (EXPERIMENTAL)" 515 depends on ATARI && EXPERIMENTAL 516 help 517 If you want to be able to use the DSP56001 in Falcons, say Y. This 518 driver is still experimental, and if you don't know what it is, or 519 if you don't have this processor, just say N. 520 521 To compile this driver as a module, choose M here. 522 523config AMIGA_BUILTIN_SERIAL 524 tristate "Amiga builtin serial support" 525 depends on AMIGA 526 help 527 If you want to use your Amiga's built-in serial port in Linux, 528 answer Y. 529 530 To compile this driver as a module, choose M here. 531 532config WHIPPET_SERIAL 533 tristate "Hisoft Whippet PCMCIA serial support" 534 depends on AMIGA_PCMCIA 535 help 536 HiSoft has a web page at <http://www.hisoft.co.uk/>, but there 537 is no listing for the Whippet in their Amiga section. 538 539config MULTIFACE_III_TTY 540 tristate "Multiface Card III serial support" 541 depends on AMIGA 542 help 543 If you want to use a Multiface III card's serial port in Linux, 544 answer Y. 545 546 To compile this driver as a module, choose M here. 547 548config GVPIOEXT 549 tristate "GVP IO-Extender support" 550 depends on PARPORT=n && ZORRO 551 help 552 If you want to use a GVP IO-Extender serial card in Linux, say Y. 553 Otherwise, say N. 554 555config GVPIOEXT_LP 556 tristate "GVP IO-Extender parallel printer support" 557 depends on GVPIOEXT 558 help 559 Say Y to enable driving a printer from the parallel port on your 560 GVP IO-Extender card, N otherwise. 561 562config GVPIOEXT_PLIP 563 tristate "GVP IO-Extender PLIP support" 564 depends on GVPIOEXT 565 help 566 Say Y to enable doing IP over the parallel port on your GVP 567 IO-Extender card, N otherwise. 568 569config MAC_SCC 570 tristate "Macintosh serial support" 571 depends on MAC 572 573config MAC_HID 574 bool 575 depends on INPUT_ADBHID 576 default y 577 578config MAC_ADBKEYCODES 579 bool "Support for ADB raw keycodes" 580 depends on INPUT_ADBHID 581 help 582 This provides support for sending raw ADB keycodes to console 583 devices. This is the default up to 2.4.0, but in future this may be 584 phased out in favor of generic Linux keycodes. If you say Y here, 585 you can dynamically switch via the 586 /proc/sys/dev/mac_hid/keyboard_sends_linux_keycodes 587 sysctl and with the "keyboard_sends_linux_keycodes=" kernel 588 argument. 589 590 If unsure, say Y here. 591 592config ADB_KEYBOARD 593 bool "Support for ADB keyboard (old driver)" 594 depends on MAC && !INPUT_ADBHID 595 help 596 This option allows you to use an ADB keyboard attached to your 597 machine. Note that this disables any other (ie. PS/2) keyboard 598 support, even if your machine is physically capable of using both at 599 the same time. 600 601 If you use an ADB keyboard (4 pin connector), say Y here. 602 If you use a PS/2 keyboard (6 pin connector), say N here. 603 604config HPDCA 605 tristate "HP DCA serial support" 606 depends on DIO && SERIAL_8250 607 help 608 If you want to use the internal "DCA" serial ports on an HP300 609 machine, say Y here. 610 611config HPAPCI 612 tristate "HP APCI serial support" 613 depends on HP300 && SERIAL_8250 && EXPERIMENTAL 614 help 615 If you want to use the internal "APCI" serial ports on an HP400 616 machine, say Y here. 617 618config MVME147_SCC 619 bool "SCC support for MVME147 serial ports" 620 depends on MVME147 621 help 622 This is the driver for the serial ports on the Motorola MVME147 623 boards. Everyone using one of these boards should say Y here. 624 625config SERIAL167 626 bool "CD2401 support for MVME166/7 serial ports" 627 depends on MVME16x 628 help 629 This is the driver for the serial ports on the Motorola MVME166, 630 167, and 172 boards. Everyone using one of these boards should say 631 Y here. 632 633config MVME162_SCC 634 bool "SCC support for MVME162 serial ports" 635 depends on MVME16x 636 help 637 This is the driver for the serial ports on the Motorola MVME162 and 638 172 boards. Everyone using one of these boards should say Y here. 639 640config BVME6000_SCC 641 bool "SCC support for BVME6000 serial ports" 642 depends on BVME6000 643 help 644 This is the driver for the serial ports on the BVME4000 and BVME6000 645 boards from BVM Ltd. Everyone using one of these boards should say 646 Y here. 647 648config DN_SERIAL 649 bool "Support for DN serial port (dummy)" 650 depends on APOLLO 651 652config SERIAL_CONSOLE 653 bool "Support for serial port console" 654 depends on (AMIGA || ATARI || MAC || SUN3 || SUN3X || VME || APOLLO) && (ATARI_MFPSER=y || ATARI_SCC=y || ATARI_MIDI=y || MAC_SCC=y || AMIGA_BUILTIN_SERIAL=y || GVPIOEXT=y || MULTIFACE_III_TTY=y || SERIAL=y || MVME147_SCC || SERIAL167 || MVME162_SCC || BVME6000_SCC || DN_SERIAL) 655 ---help--- 656 If you say Y here, it will be possible to use a serial port as the 657 system console (the system console is the device which receives all 658 kernel messages and warnings and which allows logins in single user 659 mode). This could be useful if some terminal or printer is connected 660 to that serial port. 661 662 Even if you say Y here, the currently visible virtual console 663 (/dev/tty0) will still be used as the system console by default, but 664 you can alter that using a kernel command line option such as 665 "console=ttyS1". (Try "man bootparam" or see the documentation of 666 your boot loader (lilo or loadlin) about how to pass options to the 667 kernel at boot time.) 668 669 If you don't have a VGA card installed and you say Y here, the 670 kernel will automatically use the first serial line, /dev/ttyS0, as 671 system console. 672 673 If unsure, say N. 674 675endmenu 676 677source "fs/Kconfig" 678 679source "arch/m68k/Kconfig.debug" 680 681source "security/Kconfig" 682 683source "crypto/Kconfig" 684 685source "lib/Kconfig" 686